【radar physical map]]

【Product Introduction]]
Model:SYTRD-201:1 switch output;
1. Technical indicators
(1)Center frequency:24 GHz;
(2) Vertical beam width: 43 °;
(3) Horizontal beam width: 11 °;
(4)Coverage range:0.2 m~6 m;
(5) Distance adjustment range: 2.0 m~6 m(8th gear);
(6) response time: 100 ms;
(7) Signal output: switching value.
2. Detection accuracy
(1) Leakage rate of vehicle detection: 0.1;
(2) pedestrian detection miss rate: 0.1;
(3) False detection rate:0.05.
3. Mechanical properties
(1) Equipment size: 105mm × 78mm × 26mm;
(2)weight:85g;
(3)waterproof grade meetsIP-65Standard.
4. Power Requirements
(1)operating voltage range:DC 12V~18V;
(2)operating current: less90 mA/12V.
5. Working environment conditions
(1)temperature range:-40 ℃ ~ 85 ℃;
(2) Humidity range:Relative humidity 99 at 25 ℃.
6. Reliability
(1) The equipment can work continuously day and night under specified conditions, and its average time between failures;
(2)(MTBF) satisfies: MTBF≧ 15000 h.
[Technical Features]]
1. All-day and all-weather work
gate radar is millimeter wave frequency band, no special heat dissipation treatment is required, and it has the ability to work day and night continuously under weather conditions such as snow, hail, haze, etc. The product shell has IP-65waterproof requirements, there is no need to worry about rain entering the radar and causing radar damage.
2. Test accuracy
gate radar has high working frequency, good directivity and strong anti-interference. The radar is not interfered by the outside world, nor will it interfere with the external electronic equipment. The signal propagation attenuation is large, and the radiation signal intensity meets the national environmental protection requirements. The detection rate of different types of vehicles (including cars, trucks and aluminum vehicles) is higher than that of 99.9. When the vehicle and the barrier radar are at a large angle, it can also be reliably detected. The detection rate of pedestrians is higher than that of 99.9.
3. Work reliability
gate radar shell adopts a waterproof design that meets IP-65 standards. The product has low power consumption, adapts to extreme high and low temperature weather, and works continuously day and night. Under normal operating environmental conditions, the product will not be unintentionally damaged.
4. Installation flexibility
gate radar is installed and fixed on the outer surface of the gate, and vertically irradiates through the gate of vehicles or pedestrians. The installation is very convenient and flexible. For gate openings of different widths, gate radar has the convenience of setting different sensing distances through dip switches, eliminating the inconvenience of relying on computer downloading software or delineating detection areas to adapt to different distances.
5. Low installation and maintenance costs
gate radar is simple to install, maintenance-free, high reliability and easy to replace quickly. It not only overcomes the high construction cost and maintenance difficulties of the original ground coil that needs to damage the road surface and is installed by personnel, but also a radar can solve the problem of a gate exit gate or the drop control of the entrance gate gate.
6. Convenient power supply
gate radar adopts standard 12V DC power supply, which can adapt to the power supply voltage range of 6V ~ 18V and large voltage fluctuation. The power supply current requirement is not large. It can be directly powered by the gate control board without using a separate power supply device.
7. Use environment adaptability.
gate radar adopts environmental automatic detection technology without personnel intervention, which can meet the application of straight bar gate and billboard/fence gate.
[Installation and debugging]]]
1. Gateway Radar Installation

gate radar is directly installed on the outer surface of the gate chassis at the entrance and exit of the gate, and the irradiation direction of the gate radar is perpendicular to the entrance or exit direction of the gate channel.
gate radar is about 0.6m from the radar center to the ground. The installation and fixing size of the gate radar is 67mm × 67mm, and 4 M4 × 35 screws are used to connect with the gate box.
[Dimensions]]

[Installation diagram]]

[Installation Procedure]]
(1) Determine the installation direction of the gate radar according to the application type of straight pole or billboard gate;
(2) Drill 4 screw holes with a diameter of Φ4.8 and 1 cable threading hole with a diameter of Φ5.5 on the radar mounting plate of the gate;
(3) After the cable is covered with the sealing ring, it is connected to the gate box through the cable hole, and the 4 screws are inserted into the fixing hole of the radar and the sealing ring is sleeved, and then the radar is connected to the mounting plate in turn;
(4) Put washers and fixing nuts on the 4 connecting screws in sequence and tighten them to ensure reliable radar fixing.


Serial number | line color | API definition | Note |
1. | red | 12V | DC12V ± 3V |
2. | black | 12V- | power supply |
3. | white | switching value contact 1 | normally open, trigger drop lever |
4. | yellow | public | Output |
5. | blue | switching value contact 2 | is normally open and anti-smashing |
6. | brown | / | / |
7. | orange | RS485/RS232 | Serial data output |
8. | green | RS485/RS232 | Serial data output |
[Sensor Distance Settings]]
gate radar uses dip switch to set the distance, which can flexibly meet the application of gate ports with different widths. Adjust the dip switch "1", "2" and "3" dial key states, and can set a total of 8 gearsdistance. Relationship between dip switch setting and radar sensing distance of gate

Gear number | DIP switch setting status | radar sensing distance(m) |
1 foot | 2 feet | 3 feet |
1 | 0 | 0 | 0 | 2.0±0.2 |
2 | 0 | 0 | 1 | 2.5±0.2 |
3 | 0 | 1 | 0 | 3.0±0.2 |
4 | 0 | 1 | 1 | 3.5±0.2 |
5 | 1 | 0 | 0 | 4.0±0.2 |
6 | 1 | 0 | 1 | 4.5±0.2 |
7 | 1 | 1 | 0 | 5.0±0.2 |
8 | 1 | 1 | 1 | 6.0±0.2 |