Brief Introduction
Mold temperature machine also called mould temperature control machine, widely used in plastic injection molding, light guide plate die casting, rubber tires, wheel, chemical reactor, adhesive, smelting and other industries. In a broad sense, called the temperature control equipment, including heating and freezing two aspects of temperature control
Mold temperature machine in the plastic industry, the use of more common, the main role is
1, improve the forming efficiency of the product; 2, reduce the production of defective products; 3, improve the appearance of the product, inhibit product defects; 4, to speed up the progress of production, reduce energy consumption, save energy.
Mold temperature machine used in casting industry also has a lot of space, especially in the magnesium alloy and aluminum alloy manufacture, not average or inappropriate mold temperature will cause the instability of the casting dimension, in the production process of ejection casting deformation, thermal pressure, clay mold, surface depression, internal shrinkage hole and heat bubble defects. The production cycle is also affected, such as filling time, cooling time and spraying time all produce unstable variables. Die life is also due to the impact of overheating and the impact of expensive steel to produce hot cracking, accelerate its aging. In modern factories, because of the market competition, save manpower, improve quality, reduce the cost of business strategy is imperative, the use of mold temperature machine, can reduce the die preheating time and surface quality of finished product promotion and can be fully automated production. Increasing die life is a necessary means to improve productivity. The use of temperature control machine in other industries is the inevitable condition of equipment, it is also different. In PVC sheets and wheel control Wenzhong called oil heater, in the extrusion machine is called the temperature control device, rubber internal mixer devices called temperature control system or machine temperature control, these devices basically is a first rapid heating, and then thermal insulation. And in the rubber equipment, it is also a long time to implement a cooling cooling process.
Water transport type mold temperature machine
Characteristic
1, the maximum use temperature of 40 C -180 C, precise + 1; 2, microcomputer touch control operation is simple; 3, boot automatically exhaust; 4, water, water temperature display; 5, mold backwater function (optional); 6, stainless steel pipe, reducing pipe and rust; 7, fault display, maintenance professionals do not.
Function description
Common water heating series power is 6KW-30KW at 30 DEG C 120 DEG c; Oil heating series power is 6KW-72KW at 30 DEG C - 200 DEG c; High temperature water heating power series 6KW-120KW temperature of 120 DEG C to 180 DEG c; High temperature oil heating power 18KW-120KW series temperature at 250 DEG C - 350.
Oil transporting type mold temperature machine
Characteristic
1, temperature controller (using the contact mode of storage, automatic calculation, accurate and reliable can be controlled within 2 degrees Celsius, saving more than 35%; Two, 2 sets of electric heating tube, can be used alone or jointly enable; 3, heating and cooling time is fast, the temperature is stable; 4, electric heating tube and so on the stainless steel material; 5, safety protection and fault indication system is perfect;
Application industry
Application fields, petroleum and chemical industry: polymerization, condensation, distillation, melting, dehydration, forced insulation. Oil industry: fatty acid distillation, fat decomposition, condensation, esterification, vacuum odor and other reaction kettle temperature control, reactor heating. Synthetic fiber industry: polymerization, melting, spinning, stretching, drying. Textile printing and dyeing work: the heat setting roller heating, drying room heating and heat capacity of dyeing. Nonwoven industry: non woven fabrics. Feed industry: drying. Plastic and rubber industry: hot pressing, rolling, extrusion, vulcanization molding. Paper industry: dry, corrugated paper processing. Wood industry: plywood, fiber plate compression molding, laminate heating, hot pressing board heating, hydraulic machine temperature control, wood drying. Building materials: gypsum board drying, asphalt heating, concrete components maintenance. Machinery industry: spray painting, printing and drying. Food industry: oven heating, sandwich pot heating. Air conditioning industry: industrial plant and civil building heating. Industry: road asphalt melting, thermal insulation. Pharmaceutical industry: drying. Light industry: the production of ink, washing powder. Chemical Light Industry: polymerization, condensation reaction, distillation, distillation, concentration, evaporation, melting Petroleum and chemical industry: synthesis, reaction, distillation, distillation, heating, heat preservation, storage tank heating, heavy oil heating Grease: fat decomposition, dehydration, fatty acid distillation, heating, hydrogenation reaction, esterification Plastic rubber: hot pressing, rolling, extrusion, vulcanization molding Leather industry: artificial leather processing Textile printing and dyeing: heat setting, drying, baking, evaporation, melting Chemical fiber: polymerization, melt spinning, weaving processing, molding, thermosetting, extension and drying Painting paint: paint baking, drying, high-temperature solid melting, household appliances, vehicles, paint coating The car plane: coating baking paint, drying, heating molding, high temperature adhesive Wood processing: hot pressing, drying, wood processing and wood products (wood products, furniture), artificial boards (medium density fiber board), Wood board, plywood, oriented strand board, laminate molding, wood drying, wood drying, Plywood, particleboard, MDF, for fuel (sand powder, wood powder, bark, wood) Forest products industry: hot, dry, man-made board, medium density fiberboard, particleboard, OSB, wheat straw board, plywood / artificial board veneer, wood processing, materials, solid wood flooring, wood drying, wood products, furniture, solid wood flooring paper printing: corrugated board processing, paper processing, printing ink production, processing, heat melt, drying Building materials: asphalt concrete curing tank, dissolution, waterproof material and fuel production Cement: fuel heating carbon industry: asphalt heating, thermal insulation, melting, melting, dipping, mixing, molding Highway traffic, road construction machinery, asphalt heating, melting, heat preservation of municipal highway construction: asphalt heating, melting, heat preservation Asphalt heating: asphalt heating, melting Air conditioning: heating heat source, heating ventilation, radiation heating Pharmaceutical industry: pharmaceutical care Atomic energy industry: nuclear fuel processing Metal processing: pickling, electroplating, painting, oil bath, heat treatment Electrical: resin impregnation, dissolution, thermal insulation Electroplating industry: galvanized, chrome plating, silver plating
Calculation method of heating power selection
computing method 1 special circumstances need to be calculated: A, for the heater power or freezing power KW=W * * C t * S/860 * T W= mold weight or cooling water KG The t= required temperature difference between the temperature and initial temperature. C= specific heat oil (0.5), steel (0.11), water (1), plastic (0.45~0.55) T= time to heat up to the required temperature (hour) B, the size of the pump Need to understand the customer required pump flow and pressure (head) P (pressure Kg/cm2) H * =0.1 (head M) * alpha (heat transfer media specific gravity, water =1, oil =0.7-0.9) L (media required flow L / min) =Q (such as mould for heat Kcal/H) / C (media than hot water = 1 oil = 0.45) x] t (media cycle in and out of the die temperature) * alpha x 60 2 refrigeration capacity A, Q (frozen amount Kcal/H) =Q1+Q2 Q1 (raw materials into the die from the heat Kcal/H) = (per hour of injection mold material weight kg) * c * (T1-T2) * s (safety factor of 1.5 to 2) T1 raw material in the material tube temperature; T2 product removed from the mold and the temperature; Q2 hot runner generated heat Kcal/H B algorithm (a hot runner does not apply) OZ 1OZ=28.3g 1RT=7~8 (with safety factor) 1RT=3024Kcal/H=12000BTU/H=3.751KW Kcal/H 1KW=860 1 Kcal=3.97BTU 3, cooling tower with =A+B A, injection molding machine Cooling tower RT= injection machine horsepower (HP) * 0.75KW * 860Kcal * 0.4 / 3024 B, for refrigerator Cooling tower RT= refrigerator cooling tons (HP) * 1.25
Matters needing attention
When selecting the mould temperature controller, The following points are the main considerations; 1 the size and capacity of the pump. 2 internal throat size. 3 heating capacity. 4 cooling capacity. 5 control form. From the known per cycle for heat dissipating capacity we can easily calculate the cooling liquid flow volume, followed that the correct cooling capacity, mold temperature controller manufacturers provide most of the lowest pump velocity formula calculation. Table 4.1 is useful in selecting a pump, which accurately sets out the heat dissipation capacity of different plastics. The following rules of thumb are required to provide the minimum flow rate: If the temperature difference between the surface of the mold cavity is 5, @5 0.75gal/min/kW temperature difference or @5 3.4151/min/kW temperature difference If the temperature difference between the surface of the mold cavity is 1 degrees Celsius, the minimum flow rate required is five times larger than that of the 3.75gal/min/kW or 17.031/min/kW. In order to obtain the stability of the quality of the products, a lot of injection molding company should the mold cavity surface temperature control within 1 - 2 DEG C, is indeed the many injection molding manufacturers may not know the importance of the temperature difference and temperature difference that the optimum range of 5 to 8 degrees. Calculate the volume flow rate of coolant, should use the following procedures: 1 first calculated to plant a plastic / die combination of the city to be discharged heat: if With the aforementioned PC cup model as an example, the actual need to disperse the heat is: A gross (g) / cooling time (s) =208/12=17.333g/s The heat dissipation rate of PC is =368J/g or 368kJ/kg So every cycle needs to disperse the heat =368 * 17.33/1000=6.377kW 2 to calculate the volume flow rate required for cooling: According to the rule of thumb if the temperature difference between the surface of the mold cavity is 5 DEG C, X 0.75=4.78gal/min velocity =6.377 or X 3.41=21.751/min =6.377 if the temperature difference between the performance of the cavity is 1 degree Celsius is x 5=23.9gal/min velocity =4.78 or X 5=108.731/min =21.75 3 pump flow rate regulation In order to get a good heat radiation effect, the pump flow rate should be more than the results of the calculation of the minimum 10%, so you need to use 27gal/min or 120/min of the pump. 4 pump pressure regulation; The operating pressure of the general mold temperature controller in the 2 - 5bar (29-72.5psi), due to the effects of coolant volumetric flow rate of the flow resistance pressure loss under less pressure, so the pressure of the pump is higher, the velocity more stable. For very small cooling pipe mold (such as the diameter of the pipe is 236in 6mm/0.), the pump pressure will need to have 10bar (145psi) can provide sufficient cooling rate (that is, the coolant speed). In general the liquid flow rate of coolant is higher, the more the diameter of the pipe is, the greater the pump output pressure is needed. So the pressure in the general application of the mold temperature controller should be more than 3bar (43.5psi). B, heating capacity Figure 4.8 is a typical heating calculation table, which provides the required amount of heating for the mold. Figure 4.8: The vertical axis represents the weight of the die 1. 2 axis represents the mold temperature to the desired temperature of the heat, the unit is kW/hr. The relationship between the temperature of slash 3.37 to 121 DEG C. provide heating capability of mould weight and mold temperature controller in the corresponding temperature. For example, from which we can know: 1 the weight of 500kg mold temperature to 50 degrees Celsius required for the heating capacity is 3.3kW/hr. 2 the weight of the mold temperature to 65 700kg required to heat capacity is 6.5kW/hr. Generally speaking, the stronger the heating capacity, the required heating time, then the corresponding reduction (heating capacity of double, heating time reduction). Is often because the ability of the controller is too low, causing the mold can not reach the best temperature state. To know the actual performance of the die temperature controller, we can compare it to the actual and calculated mold heating time.
Freezing capacity
The design of the freezing line of the temperature controller and the composition of the parts are important for the precise control of the mold temperature. When the mold or heating the liquid temperature rises to the set value, the mold temperature controller must can quickly and effectively avoid the temperature continues to rise, the introduction of another low temperature liquid, the introduction of control by electromagnetic valve is responsible for. So the elimination and stability of temperature override depends on the size of the solenoid valve. The aperture of the cooling solenoid valve can be calculated by the following formula: The cooling capacity of (gal/min) =kW * 3.16/ t Here a t= mold temperature controller set production temperature and chilled water temperature difference: KW= mold needs to be discharged in the heat The following table lists the volume flow rates that can be provided by different solenoid valves: Electromagnetic valve aperture volume flow rate Mm gal/min 1/min in 6.35 0.7 3.18 0.25 9.53 1.2 5.45 0.375 12.70 3.3 14.98 0.500 19.65 5.4 24.52 0.750 25.40 10 45.40 1 31.75 13 59.02 1.250 38.10 20 90.80 1.500 After calculating the freezing capacity, we can find out the corresponding electromagnetic valve from the above table, such as the following example: PC cup mode needs to be discharged heat is 6.377kW The set temperature is 90 The freezing water temperature is 18 The T=9018=72 C So frozen ability =6.377 * 316/72=0.28gal/min or 1.271/min From the above table can be known that the size of the 6.35mm/0.250in solenoid valve can provide sufficient volume flow rate, suitable for use in the mold temperature control range is + 1 C. Solenoid valve pressure drop affect the flow rate. The flow rate of the above table is based on the pressure drop of 1bar (14.5psi). So the pressure drop is higher, the faster flow rate of chilled water. The typical pressure drop of solenoid valve is 2bar (29psi). C, liquid type mold temperature heating control system The main purpose of any one temperature controller is to control the mold temperature in the range of (+ 2 degrees F). So for the operation of the mold pipe between the temperature of the temperature must be accurate, or the purpose of temperature control can not be achieved. Only some control methods of mold temperature controller to open / close the form, its working principle is to compare the actual and the set temperature. If the actual temperature comparing the set temperature is much lower, electric will fully open until the actual temperature reaches the set value, the electric heating has been closed, due to an open / closed form of the control system has great practical positive and negative temperature deviation. The temperature changes not only the gods directly affects the temperature of the liquid, also indirectly to die a lot of excessive lifting, needless to say the need to reflect on the quality of the finished product. So we should use the PID (proportional, integral, differential) form of the heating control system, which can ensure that the mold temperature control to maintain in the range of + 2 degrees Celsius (+ 1 degrees F).
Operation flow
一、Check before start
1, around whether clean without impurities, check the power supply, heater, controller, pressure gauge, pump and so on are normal. 2, check whether the liquid level in the expansion tank oil level 1/23/5 above position, water level sensor is normal or not. 3, switch on the control cabinet power supply, check the voltage is normal, check the indicator light and the display instrument is normal.
二、Start-up
1, start the thermal oil circulation pump, pump after the normal cycle of about 0.5 hours to make the pressure stable; 2, press the heating start button, observe whether the normal heating;
三、 Shutdown operation
1, normal shutdown (1) gradually reduce the temperature, and the heating is stopped; II to be conducting oil temperature dropped to below 70 DEG C, stop the operation of the heat conduction oil circulation pump; third, turn off the power supply, do a good job shift records. 2, emergency stop if due to an emergency emergency stop, should quickly turn off the heating pipes, in order to guide oil natural cooling, to prevent overheating.
四、Matters needing attention
1, check should pay attention to the power and check the heat-conducting oil furnace around whether leakage occurs, near configuration should be enough oil and electrical fire fighting equipment, no water as fire extinguishing agent; Select the appropriate mode temperature controller Random purchase mold temperature products can bring the loss of 20% profit, so we must consider the need for production in the purchase, strict validation of the ability of the temperature controller, to make a decision. Unfortunately, people often ignore the very important part of this injection molding technology, often in the productivity and quality of the problem to wake up.
Mold temperature machine maintenance
1 to buy a new mold temperature machine, please check the cooling water before use, to prevent the flow of cooling water to prevent the failure of the mold temperature machine. We should keep the working environment clean and avoid dust, which can prolong the service life of the electrical components of the mould. 2 new mold temperature machine, we need to use the heat conduction media to make different maintenance measures. For the medium is water, we should keep the water clean, it is not easy to scale, but also to prevent the pipeline blockage. For medium is oil, we should according to the use of temperature, regular replacement, for more than 200 DEG C, we need to replace a regular one or two months, and below 200 DEG C, we can a quarter about a replacement, so it is good to avoid the temperature and not the problem. 3. In the pipeline, we should according to the relationship between the pump and the pressure, to determine whether blocking phenomenon of pipelines, if pressure is too small, we can heating tube was removed and cleaned with tools, particularly a cover system inlet filter mesh, the best one month cleaning time. 4 regularly check the mold temperature machine pumps and pump for leaks, if necessary, can also be regular replacement pump. 5 electrical components, we can according to the service life of components in a timely manner to replace, regular testing to ensure safety.
Cooling mode
The cooling way of the mold temperature machine is divided into direct cooling and indirect cooling. The indirect cooling method uses the cooling circuit and the main circuit separately, and the direct cooling mode, the cooling circuit directly participates in the main circuit. The direct cooling mode is adopted in the water transport mode. And transport type mold temperature machine oil, due to the heating process, the water and oil can not be doped together, so the indirect cooling mode, its approach is usually used plate heat exchanger for cooling. High temperature transport water type mold temperature machine due to the temperature usually used in more than 160 DEG C. Therefore, road in charge of internal circulation for high temperature steam, when the internal pressure of the pipe is relatively large, if the use of direct cooling and need to external water pressure is greater than internal main pressure can enter a director for the cooling. This method is easy to life in danger. So the high temperature water type mold temperature machine also uses the indirect cooling method. Advantages and disadvantages of direct cooling: direct cooling can only be used for low temperature occasions, but the cooling rate is fast. The advantages and disadvantages of indirect cooling indirect cooling for high temperature mold temperature machine, but the heat exchange speed, heat will in heat exchange loss. Therefore, when the actual temperature and the set value of the medium deviation, we use a larger cooling capacity of direct cooling. Direct cooling and indirect cooling
Application
1, injection mold thermal balance control of injection molding machine and mold heat transfer is the key to the production of injection molding parts. The heat transferred from the plastic (e.g., thermoplastic) to the material and the mold by heat radiation. In addition, the heat is transferred to the atmosphere and die by thermal radiation. By the heat transfer fluid of the heat absorbed by the mold temperature human away. 2, mold temperature and mold temperature control of injection molding effect of injection molding process, one of the main purposes of mold temperature control is the mould is heated to operating temperature, the second is to maintain the constant temperature of mold in the working temperature. The success of the above two points, you can optimize the cycle time, thereby ensuring the stability of injection molding parts of high quality. Mold temperature will affect the surface quality, liquidity, shrinkage rate, injection molding cycle, as well as deformation and so on. Mold temperature is too high or insufficient to different materials will bring different effects. In terms of the thermoplastic, the mold temperature is a little high, usually to improve the surface quality and liquidity, but will extend the cooling time and injection cycle. Lower mold temperature will decrease the shrinkage in the mold, but will increase the rate of shrinkage of injection molded parts. For thermosetting plastics, a higher mold temperature usually reduces cycle time, and time is determined by the time required for the cooling of the part. In addition, in the processing of plastic, a little higher mold temperature will reduce the plastic time, reduce the number of cycles. 3, effective control of mold temperature of the preparation conditions of the temperature control system by the mold, the mold temperature machine, heat conduction fluid three parts. In order to ensure that the heat can be added to the mold or removed. Each part of the system must meet the following conditions: the first is in the mold, the surface area of the cooling channels must be large enough, the runner diameter to match pump (pump pressure). The temperature distribution in the cavity has a great influence on the deformation and the internal pressure of the parts. Reasonable cooling channel can reduce the internal pressure, which can improve the quality of injection parts. It can also shorten the cycle time, reduce the cost of products. Followed by the mold temperature machine must be able to make the temperature of the heat conduction fluid in the range of 1 degrees -3 degrees C, specific according to the quality requirements of injection parts. Third is the heat conduction fluid must have good heat conduction ability, the most important is, it should be able to import or export a lot of heat in a short time. From the point of view of thermodynamics, water is better than oil.
Working principle
The mold temperature machine is composed of water tank, heating and cooling system, power transmission system, liquid level control system, temperature sensor, injection port and other devices. Usually case, power transmission system in the pump to heat fluid from equipped with built-in heater and cooler tank get to the mold, then back to the water tank from the mold; temperature sensor to measure thermal fluid temperature and the data is transmitted to the control part of the controller; controller regulates the temperature of the hot fluid, thereby indirectly regulating the mold temperature. If the mold temperature machine in the production, the temperature of the mold more than the controller set value, the controller will open the electromagnetic valve connected to the water inlet pipe, until the temperature of the hot fluid, that is, the temperature of the mold back to the set value. If the mold temperature is below the set value, the controller will turn on the heater.