Single seat regulating valve

A brief introduction:
HTS seriesSingle seat control valveIs a top guide structure regulating valve, the valve fluid channel was streamlined S, the pressure drop, flow rate, wide adjustable range and high precision valve flow characteristic curve, oriented area, good vibration resistance.The valve is equipped with multi spring diaphragm actuator, compact structure, large output force.Can be used to control various fluid pressure and temperature.
Two,Single seat control valveThe performance:
1, leakage: metal seat: meet ANSIB16.104 IV, less than the rated Cv 0.01%;
2, soft seat: meet ANSIB16.104 VI, less than the rated;
3, quick opening valve: less than rated Cv 0.00001%;
4, return difference: 1% (with locator); 3% (without locator);
5, linear: + l% (with a locator); + 5% (without locator);
6, note: V PTFE standard;
7, adjustable range: 50 to L (Cv = 1) or 30 (Cv = 0.63): 1.
Three,Single seat control valveThe main technical parameters:
1 types: direct single seat casting ball valve;
2, nominal diameter: 20, 25mm;
3, nominal pressure: SD-HLSI125, 150, 300, 600, 10, 16, 20; JIS, 30, 40K PNl.6, 4, 6.4MPa
4, connection type: flange type: FF, RF, RJ and LG; according to standard of ANSI Bl6.5, JISB2201JB/T79.1PNl.6MPa JB/T79.2, concave convex surface;
5, welding weld type: SW;
6 material: HT200ZG25 ZG1Cr18Ni9; ZG0Cr17Ni12Mo21.25Cr0.5Mo5.0Cr0.5Mo, SDPH21SCPH61Ti;
7, valve cover: normal temperature type (P):-l7 ~ +230 c;
8, elongation type 1 (E1):-45 ~ -17 ~ +566 C C, +230;
9, elongation of type II (E2): integral (E2I): -100 ~ -45 welding type C (E2W): -196-100 c;
10, glａnd type: bolt cl
11, packing: V PTFE, PTFE impregnated asbestos packing, asbestos braid packing.
The four component, single seat control valve of the valve:
1, spool type: single seat plunger type valve;
2, flow characteristics: metal seat: Cv value from high precision flow characteristics of 0.4 ~ 14 with IEC534-2;
The scope of work: 3, soft seat, working temperature and pressure welding division Chatterley working temperature and pressure difference;
4, material: 1Cr18Ni9 division stellite alloy surfacing 9Crl8MoV.
Five, actuator:
1, type: HA multi spring diaphragm actuator;
2, the diaphragm material: rubber nylon clip;
3, spring range: 0.02 ~ 0.10, 0.08 ~ 0.24MPa;
4, air pressure: 0.14, 0.16, 0.28, 0.40MPa;
5, joint source: Rc l/4;
6, the environment temperature: -30 ~ +70 c;
7, valve type: gas - gas - open or closed;
8, annex: locator, hａnd wheel, pneumatic valve position transmitter.
Six, value and travel:

Note: 1, symbols, and delta said valve specifications.2, the symbol said the flow characteristic of the valve according to the standard of IEC 534-2.
Seven, allow pressure:
1. The plunger valve, metal seat (%CF, LCF) A. gas - off valve 100KPa

B. gas valve open

Note: 1. does not exceed the maximum allowable pressure of ANSI B16.34 or JIS B2201 standard maximum working pressure.
Figure 2. the same box above said valve is normally open to allow pressure, under the digital representation allows the differential pressure valve is fully closed when the.
Allow pressure 3. with *, valve control liquid, allowing the pressure is only 3MPa, more than 3MPa, please use the LHLC valve.
4. ash bottom box number indicates valve equipped with standard actuator.
Eight, flange from mm:

Note: the flange from conforms to the IEC534-3 standard.
Nine, size mm:

Note: the H column is not size regulating valve with hａnd wheel, if the belt wheel mechanism to the corresponding plus hａnd wheel size.
10, flange:

Eleven, welding connection:

Design selection and ordering information:
1, product type and name;
2, the nominal diameter of DNmm;
3, nominal pressure;
The requirements of 4, flow characteristics;
5, body material and trim materials;
6, medium type and temperature range;
7, valve and pressure (pressure difference);
8, seal form;
9, accessories.