-
E-mail
rbzg@rbqlty.com
-
Phone
13855367553
-
Address
Ma'anshan City
Membership
Help
Anhui Runbang Heavy Industry Machinery Co., LtdFree·1YRS
rbzg@rbqlty.com
13855367553
Ma'anshan City




(3-12)X2000mm
This line is apply for various kinds of steel plates slitting, recoiling. It used to uncoiling large coil drum plate, and slitting into umpty strips as required width, then to recoiling and packing into whole bale of plane plate for next procedure of cold-bending, punching, pipe welder, etc.
Working Process:
Charging—uncoiling—pressing and guiding—pinch preleveler—scrap shear—transitional worktable —guiding—slitting—scrap winding—loop bridge —pre-separating—damping pressing—separating—recoiling—manual baling—discharging.
Major Technical Parameter:
Vertical tolerance(side bending): ≤0.8mm/m
12. Slitting strips:thickness 3━6mm:13strips;7━8mm:8strips ;9━10mm:6strips,
11━12mm:5strips;equipped blade 28pcs
Composed devices:
V-shaped coil saddle, hydraulic coil car, hydraulic conical uncoiler, hydraulic pressing and guiding & shovel-head device, hydraulic pinch pre-leveler, scrap shear, transitional worktable, guiding device, slitting machine, scrap winder, hydraulic ,hydraulic loop bridge, hydraulic pre-separator, hydraulic separator, hydraulic Recoiler, hydraulic supporting stand, hydraulic unloading car, hydraulic system, electric system.
Structure summary :
1.V-shaped coil saddle
It used to discharging coil of steel strip, so it could prevent coil car from damaging when directly suspended the stripes on it.
One pair of it, 2pcs.
A. Loading capacity is 30T. Hydraulic lifting & moving.
B. This is composed of bottom stand, axle, wheel, bearing, guide column, guide cover, top supporting stand, V-shaped table, hydraulic lifting oil cylinder, hydraulic running motor,etc.
C. Parameter
ITEM | PARAMETER | No. |
Lifting oil cylinder | Piston diameterφ220mm;Stroke 700mm | 1pcs |
Running motor | Cycloid hydraulic motor: BM4W-500 | 1pcs |
Guide column diameter | φ120mm | 4pcs |
bearing | type:313;214 | 4 pcs for each |
D. Summary
It used to loading and lifting the coil strip onto uncoiler machine for charging.
3.hydraulic uncoiler
A. Uncoiler : a pair of conical uncoiler
B. Composition : it is composed of guiding stand, frame, charging shaft, conical charging tray, hydraulic opposing vertexes device,etc. Charging machine is hydraulic brake.
B.Parameter
ITEM | PARAMETER | No. |
Uncoiler type | Top cone | A pair |
Expanding range | φ508-φ800mm |
|
Brake | YWZ400/45 | 2pcs |
Centering oil cylinder | φ125*1100mm |
|
C. Summary :
Two pcs of uncoiler will centrally clamp the coil strip while lifted by hydraulic charging car, at the moment of coil strip core centering to uncoilr core. Centering discharging oil cylinder could work individually or synchronously for coiling. When there is a divergence of coil center and the product line center, the machine could synchronous load the strip for coiling by left or right centering. While uncoiling, the brake will be loosen and match with pressing and guiding wheel speed as stated which could increase power of uncoiling. Leveling stopped, brake begins braking.
4. Hydraulic pressing and guiding ,shovel head, pinch and pre-leveler
A. It is composed of frame type stand, hydraulic pressing and guiding device, hydraulic shovel head ,etc.
a.hydraulic pressing and guiding device: it is composed of hydraulic pressing and guiding arm, pressing and guiding wheel, chain , chain wheel. Hydraulic coil opener, equipped with hydraulic oil motor.
b.hydraulic shovel device: shovel head housing,hydraulic contracting shovel head, shove head hydraulic balancing device.
B.parameter
ITEM | PARAMETER | No. |
Pressing and guiding oil motor | 1QJM52-6.3 | 1pcs |
Pressing and guiding oil cylinder | Piston dia.:φ125mm,Stroke 270mm | 2pcs synchronous |
Coil opener oil cylinder | Piston dia.:φ125mm,Stroke500mm | 1pcs |
Contracting oil cylinder | Piston dia.:φ80mm,Stroke390mm | 1pcs |
Balancing oil cylinder | Piston dia.:φ100mm,Stroke270mm | 2pcs synchronous |
Pinch and pre-leveler
Power part: This is composed of power stand, decelerator, pneumatic clutch, brake, DC motor, power distributing case, 7 pcs of universal joint.
Host part: This is composed of pinch and pre-leveling machine, cast steel frame, up shaft stand, cross bar, a group of pinch roller, 5 pcs of pre-leveling roller, lifting and pressing down device of hydraulic pinch, electric lifting and pressing device of pre-leveling roller.
B.parameter :
NAME | PARAMETER | No. | Rmks |
Pinch roller | Dia.:f220mm,material 40Cr | 2 | HRC50-54 |
Pre-leveling roller | Dia.:f220mm,material 40Cr | 5 | HRC50-54 |
Pre-leveling roller spacing | 290mm |
|
|
Motor type | Z4-180-41 |
|
|
Motor power | 75KW,1500r/min | 1 | Encoder feedback |
Reducer | ZQ750,r=31.5 | 1 |
|
Pinching oil cylinder | Dia.:f100mm,Stroke:220mm | 2 | Synchronous |
Pressing motor of pre-leveler | BWD3 KW | 2 | Up & down with proximity switch |
Pinch potent width | 2000mm |
|
|
C.Summary:
After coil opener, plate will enter into pinch and pre-leveling machine, pinch oil cylinder press down, clamp the plate head, DC speed adjustable motor starts, so plate will feed into the adjusted pre-leveler. When plate-head out from the machine, open pressing arm, put down shovel frame, draw back shovel head, stop discharging motor, open discharging clutch, thus made the plate delivering ahead. The operation speed of Eurotherm electric cabinet can synchronous with the speed of slitting line
5.Shearing machine is hydraulic cutting machine 12x2500mm; it is used for cutting and separating the head and tail of coil plate, equipped with 2pcs roller drum which avoid scratching , and prevent friction on the blade edge.
6.Transitional worktable 1
Potent width :>plate width, length:4m.
Rollaway nest diameter: Φ140mm, equipped bearing:14pcs(type:212)
7.Hydraulic guiding device
ITEM | PARAMETER | No. |
Potent width | 800—2000mm |
|
Pressing roller | Diameterφ160mm |
|
Centering oil cylinder | φ125*800mm |
|
C. Summary
Its function is to centering the pinched and pre-flattened plate to the axis of slitting machine, in order to prevent the plates from shifting, and made the strips steel alike. Guiding roller can be adjusted individually or synchronously centering or left and right synchronously movements.
8. Slitting machine(important equipment of production line)
Slitting machine is the main equipment of this line which divided into power part and host part.
Host part is composed of frame, fixed frame, fixed big bearing stand, sliding big bearing stand , movable frame, fixed small bearing stand, slide small bearing stand, 2 pcs of blade shaft, lifting and pressing device of synchronously worm gear and worm rod(up & down with proximity switch), hydraulic pushing device, etc. accompany of blades, spacers, rubber rings . At the exit side of slitting machine is equipped with 1 set transitional reversal plate of hydraulic lifting
NAME | PARAMETER |
reducer type | ZS1250-r=50 |
Motor type | Z4-250-42 200KW/1000r(encoder feedback) |
Blade shaft diameter | Φ320mm |
Potent width | >processed width |
Blade material , hardness | H13K,HRC56-59 |
Blade specification | Φ320XΦ480x25mm |
Main bearing | 672758,8256:2set for each, 7238,238:2 set for each |
Oil cylinder of frame pushing and pulling type | Dia::Φ125mm,Stroke : 700mm |
Lifting motor of main shaft | BWD13-35-3power :3KW |
Its function is to divide the raw material into several strips as stated width, orderly and uniform.
One side of frame is hydraulic push-pull pattern, two pcs of main shaft is suspended arm which is easy to changing blade and satisfying various plates cutting with different width. The main shaft is main driven, main bearing is mill one with high hardness. High precision of blade and separating cover. Lifting and pressing main shaft is adopt synchronously worm gear and worm rod adjustment, so both side of blade will be alike, uniform in strength, thus will protect the blade and longer their lift and higher cutting precision.
9. Hydraulic Scrap winder
A. Composition :
Scrap winder is composed of frame, scrap shaft, scrap tray, scrap winding device, guiding device for scrap winder, etc., accompany of chain, sprocket, chain cover, decelerator, torque motor, etc.
B. Parameter
ITEM | PARAMETER | No. |
Decelerator-speed ratio | KAF97-22.37 |
|
Torque motor | YLJ180-250/137N/M | 2 pcs |
Oil cylinder | Double ear Φ80/Φ40x800mm |
|
C. Summary
Its function is to collect the waste scrap after slitting.
10. Hydraulic loop bridge (effective length 8m)
It is composed of frame, rollaway nest, supporting plate, bearing stand,oil cylinder,etc.
11. Hydraulic pre-separator
A. This is composed of bottom-stand, pre-separating axle, separating pad, separator slice, bearing stand, etc.
Pressing roller device is composed of frame, slide, 5pcs of damping pressing roller device(exit upper roller with encoder), hydraulic pressing and lifting device, hydraulic support platform, etc.
B. Parameter:
ITEM | PARAMETER |
Pre-separating axle diameter | φ150mm |
Pre-separating cover | φ150×φ175×Hmm |
Pre-separating H | φ150×φ270×8mm, 14pcs |
Damping pressing axle diameter | Φ220mm |
Main bearing | 216: 8 sets |
2 pcs of synchronous damping oil cylinder diameter: | Φ150mm,Stroke:150mm(piston rod length extend 160m) |
Oil cylinder of support platform | Double ear cylinderφ63x300mm |
C. Summary
It is used for separating the strip plate orderly, in order to avoid winding. The function of hydraulic pressing roller is compress the separated strip, the one is to prevent the coil plate from jumping during running procession, and jump out of the pre-separating slice and wind, the other is to increase recoiling damping, to make recoiling device tighten the plate strip.
A. It is composed of separating stand, pressing and separating arm, oil cylinder for pressing and separating , pressing oil cylinder, synchronous rack for separating shaft,gear wheel, pressing and separating shaft, pressing and separating slice, spacer, pressing shaft,etc.
B. Parameter:
NAME | SPECISICATION | No. | REMARK |
Pressing oil cylinder | Φ125X500mm | 2pcs | Middle pendulum |
Pressing separating oil cylinder | Φ63X250mm | 1pcs |
|
Pressing shaft | Φ150mm | 1pcs |
|
C. Summary :
Function of hydraulic pressing and separating device is to separating the coil strips on recoiling machine orderly, tighten the strip under the function of hydraulic, so to bale the coil strips easily, otherwise the coil plate will loose.
13. Hydraulic Recoiler
B. Parameter
NAME | SPECISICATION |
Decelerator | i=90.18(or 59.1)speed adjustable |
Type of direct-current motor | Z4-280-42, |
Power of direct-current motor | 250KW/1000r(encoder feedback) |
Recoiling plate thickness | ≤12mm |
Recoiling speed | adjustable |
Moveable oil cylinder diameter | φ125mm, Stroke:580mm |
Weight of recoiling | ≤30T |
Recoiler main shaft | Φ320mm |
Recoiling diameter | Φ760mm |
Recoiling potent width | >coil plate width |
C. Summary
It used to recoiling the slitted strips on recoiling plate.
Different plate separated, the jaw catch the head of coil plate after coil inserted plate tank, then rotate to make the slitted coil recoiled.
The expansion diameter φ760mm, hydraulic unloading car will support the strip bullnose, then put down hydraulic supporting arm, and expanse Max diameter will reduce to the end. At last, gradually drop-out the material.
14. Hydraulic unloading car
A. This is composed of car bottom stand, axle, bearing stand, wheel, hydraulic lifting device, guiding rod, guiding cover, upper supporting stand, hydraulic running device, etc.
B. Parameter
ITEM | PARAMETER |
Potent length of supporting stand | >coil width |
Lifting oil cylinder | Diameter:φ200mm, Stroke: 700mm |
Running oil cylinder | Diameter:φ100mm, Stroke: 3200mm |
C. Summary
Its function is to loading the baled strip plate to move out for hoisting easily.
15. Hydraulic system (hydraulic oil, lubrication oil shall be provided by user-self)
Hydraulic system is an important part of this line, it is one of power resource.
There are 2 sets hydraulic station, front and back are separated station. front station is high pressure pump with a pair of high pressure interface in which to privide power for shear. rated pressure is 32Mpa, working pressure is 30Mpa, other interface pressure decreased to 12Mpa
B. Parameter:
ITEM | PARAMETER |
Power | 15KW(plunger pump)+11KW(vane pump) |
Rated working pressure | 16Mpa(max) |
Flow rate | 40L/min |
Common working pressure, ≤ | ≤10Mpa—12Mpa |
Oil temperature | ﹣5℃—+55℃ (fan) |
All the seal rings is exported from Nok, Japan.
16. Electric Control System(wire and cable shall be provided by user-self)
A. Accompany of distributing system: power incoming voltage: AC380V 50Hz.
Voltage level: alternative voltage: AC380V 50Hz
Control voltage: AC220V, 50Hz
Hydraulic voltage: DC24V
B. The electric system of slitting line is composed of direct-current cabinet, host operation cabinet, auxiliary cabinet. DC speed adjustment system control this line. Movement condition can divided into linkage and man operation which control the movements of each single machine.
C. These operation cabinet have emergency terminal button. Pressing anyone, the whole line will terminated for the security of both man and machine.
VI. INSTALLATION AND ADJUSTMENT
1.The installation length of (3-12)x2000mm slitting line is about 32m, the elevation height of this line (working surface to ground) is 800mm, each stand-alone machine is installed according to the foundation drawing.
2. The center line of every individual machine must be conformed to the center line of this production line.
3. The center line of later running of each individual machine is mutual parallel and vertical to the main center line, the center line of main shaft reach to horizontal position.
4. The total power of this production line is 560KW, each individual machine’ power of this line connected by electrical schematic drawing and wiring drawing, hydraulic connecting is according to hydraulic schematic drawing,after switching on the power and hydraulic system ,each individual machine proceed individual trial running.
5. The adjustment of slitting line
A. The two blade shaft of slitting shear are all for active, the frame are all for cast steel frame, the moving of movable frame is hydraulic push-pull type, the lower balde shaft is fixed-suspended arm, the upper blade shaft is sliding suspended arm, it have advantage for equipping blade quickly.
B. The method of slitting adjustment
a. Lift up the upper blade shaft by double worm gear and worm rob, to make center Stroke between the two blade shaft is greater than blade outside diameter, 2-12mm slitting machine: blade OD.: Φ480mm , center Stroke: ≥485mm
b. Hydraulic pushing movable frame
c. Determine the space between the upper and lower blade according to the slitting plate thickness. Equation : S=thickness X(10━15)%/2
d. The method of blade arrangement : arrange the blade to the both side of center line according to the center line of production line, before arrange blade, the separated roll of blade should be cleaned debris, and don’t use hard wast,fiber to wipe. Arrange the lower blade first, and then arrange the upper ones, convex blade with big rubber rings, concave blade with small rubber rings, not too much or too little. After arranging blade shaft, make one side of lock nut locking. The cutting length of blade general take 1.0-2.0mm, and use positioning nut locking.
e. Can’t use large hardness metal material to trial cutting, sharp cutting edge of blade shall not use objects to hit, temporary unused blade should be cleaned,and oiled to prevent the mental surface from rusting. The blade should be grind after using, and use core rod to grind the outside uniformly, strictly forbidden to grind the both side of blade.

