ZXM

NegotiableUpdate on July 04

Model

Nature of the Manufacturer: Other

Product Category: Regulator valve

Place of Origin: City, Province

Online Consult Contact Information

Overview

ZXM

Product Details

ZXM series pneumatic membrane sleeve valve is a kind of pressure balance control valve. Equipped with multi spring actuator, the compact structure, light weight, good stability. Fluid channel is S streamline, pressure drop loss, allows the pressure difference is big, the noise is small, the circulation ability is big. Widely used in precise control of gas, fluid and other media parameters such as pressure, flow, temperature, liquid level to maintain a given value. Especially suitable for large flow, pressure difference, low leakage requirements of the occasion.
This series of products have the standard type and regulating cut off type, bellows seal type, jacket insulation type and other varieties. Product nominal pressure level is PN10, 16, 40, 64; body diameter range DN20~200. Applicable fluid temperature by -200 degrees C ~+560 C, the range of a variety of grades. Leakage standard has IV or VI level. The flow characteristic is linear or equal. Variety of specifications available for selection.

Valve body, valve cover：HT200，ZG230-450，ZG1Cr18Ni9Ti

   Valve core and valve seat：1Cr18Ni9Ti，司太莱合金堆焊

   Soft sealing valve core：Reinforced PTFE

   Filler：PTFE, flexible graphite

   Corrugated pipe：1Cr18Ni9Ti

  Filling piece：Asbestos rubber sheet、10^#、1Cr18Ni9TiAsbestos gasket

   Membrane cover：A3

Corrugated diaphragm：Ding Qing Rubber Sandwich reinforced polyester fabric

   Spring：60SIMN

   Stem, push rod：2Cr13、1Cr18Ni9Ti

   Bushing：2Cr13

Nominal diameter DN（mm）		20	25	32	40	50	65	80	100	125	150	200
Rated flow coefficient KV	straight line	6.9	11	17.4	27.5	44	69	110	176	275	440	690
	Equal percentage	6.3	10	16	25	40	63	100	160	250	400	630
Rated travel L（mm）		16			25			40		60
Ae（cm2）		280			400			600		1000
Signal range Pr(KPa)		20~100、40~200
Gas pressure Ps(MPa)		0.14~0.4
Inherent flow characteristic		Linear, equal percentage
Inherently adjustable ratio		50
Allowable leakage		Hard seat unbalanced type: IV level (10-4 rated capacity) soft seat: VI
Nominal pressure PN（MPa）		1.0、1.6、4.0、6.4
working temperaturet（℃）	Normal temperature type	-20~200、-40~240、-60~250
	Heat dissipation type	-40~450、-60~450
	High temperature type	300~560
	Low temperature type	-60~-100、-100~-200、-200~-250

Nominal diameter	20		25	32		40	50		65	80		100		125		150		200
	282			308					394					494
L	PN16，40		150		160	180		200			230		290		310		350		400	480	600
	PN64		230		230	260		260			300		340		380		430		500	550	650
H1	PN16		52.5		57.5	70		75			82.5		92.5		100		110		125	143	170
	PN40		52.5		57.5	70		75			82.5		92.5		100		117.5		135	150	187.5
	PN64		65		70	78		85			90		102.5		107.5		125		147.5	172.5	207.5
H	mark accurate type	PN16	429		438	474		476			502		622		646		687		835	889	981
		PN40	429		438	474		476			502		622		646		695		845	896	1000
		PN64	456		468	511		525			535		663		673		705		868	958	1260
	Heat radiation high temperature type		570		570	610		610			630		730		810		820		960	1090	1180

Standard type, heat sink, high temperature type：MM

*Heat radiation, high temperature type（H）byPN16Numerical value

**The height of jacketH₁And H were increased15%

Bellows seal type unit：MM

Nominal diameter	20	25	32	40	50	65	80	100	125	150	200
A	282		308			394			494
L	150	160	180	200	230	290	310	350	400	480	600
H1	52.5	57.5	70	75	82.5	92.5	100	117.5	135	150	187.5
H Corrugated pipe type	499	511	560	617	620	710	767	792.5	807	1057.5	1087.5

External dimension table

Nominal diameter			20	25	32	40	50	65	80	100	125	150	200
A			282		308			394			494
L	PN16, PN40		150	160	180	200	230	290	310	350	400	480	600
	PN64		230	230	260	260	300	340	380	430	500	550	650
H1	PN16, PN40		52.5	57.5	70	75	82.5	92.5	100	117.5	135	150	187.5
	PN64		65	70	77.5	85	900	102.5	107.5	125	147.5	172.5	207.5
H2	-60~-100℃		500	500	500	500	500	600	600	600	700	700	700
	-100~-200℃		700	700	700	700	700	800	800	800	900	900	900
	-200~-250℃		900	900	900	900	900	1000	1000	1000	1100	1100	1100
H	-60~ -100 (℃)	PN16, PN40	862.5	865	902	907	914.5	1118.5	1126	1141.5	1135	1348	1385.5
		PN64	875	874	909.5	917	922	1128.5	1133.5	1149	1347.5	1370.5	1405.5
	-100~ -200 (℃)	PN16, PN40	1062.5	1075	1102	1107	1114.5	1318.5	1326	1349	1547.5	1570.5	1605.5
		PN64	1075	1080	1109.5	1117	1122	1328.5	1333.5	1349	1547.5	1570.5	1605.5
	-200~ -250 (℃)	PN16, PN40	1262.5	1267.5	1302	1307	1314.5	1518.5	1526	1541.5	1735	1748	1785.5
		PN64	1275	1280	1309.5	1317	1322	1528.5	1533.5	1549	1747.5	1770.5	1805.5
D3			260	260	285	305	340	370	405	460	525	590	700
D4			290	290	315	335	370	400	435	490	555	630	740
Bolt hole N(individual)-DD iameter			8-14	8-14	8-14	8-16	8-16	10-16	10-16	12-18	14-18	16-18	18-18

Regulating valve weight meter unit:KG

Nominal diameter		20	25	32	40	50	65	80	100	125	150	200
Standard type	PN16	16	17	19	21	23	35	48	57	64	70	900
	PN40	16	17	19	21	23	35	48	60	67	74	95
	PN64	20	21	25	30	33	44	71	91	100	115	145
Heat radiation high temperature type		17	18	20	22	25	36	51	60	67	74	95
Corrugated pipe type		20	21	25	30	33	48	71	91	102	115	145
Low temperature type		20	21	23	26	28	42	58	69	77	84	108