Description
Sharetop’s 100G CFP2 LR4 or ER4 optical receiver integrates the 4 receive paths onto one module. On the receive side, 4 lanes of optical data streams are optically demultiplexed by an integrated optical demultiplexer. Each data steam is recovered by a PIN photodetector or APD and transimpedance amplifier, retimed, and passed on to an output driver. This module features a hot-pluggable electrical interface, low power consumption, and MDIO management interface.
Product Features
●Supports up to 112Gbps bit rates
●Duplex LC connector
●Hot pluggable
●PIN or APD ROSA
●Operating electrical serial data rate up to 27.952493Gbps
●4 parallel electrical serial interface
●Applicable for 10km(PIN) or 30km(APD) SMF connection
●Low power consumption, < 3W
●Digital Diagnostic Monitor Interfacel
●MDIO Communication Interface
●Compliant with 100GBASE-LR4,ER4 and OTU4
●Operating case temperature:
Commerical:0 to 70 °C
Applications
●Local Area Network(LAN)
●Wide Area Network(WAN)
●Switch to router interface
●ITU-T OTU4 OTL4.4
Standards
●Compliant with IEEE 802.3ba
●Compliant with CFP2 MSA hardware specifications
●Compliant with CFP2 MSA management specifications
●Compliant with ITU-T G709/Y.1331
●Compliant with RoHS
- Product Specification -
Optical Characteristics
(Tested under recommended operating conditions,unless otherwise noted)
Parameter | Symbol | Unit | Min | Typ | Max | Notes |
Optical Receiver Characteristics |
Receive Rate for Each Lane |
| Gbps |
| 25.78125 | 27.9525 |
|
Overload Input Optical Power | Pmax | dBm | 5.5 |
|
| 3 |
Average Receive Power for Each Lane | Pin | dBm | -8.6 + ∆ |
| 3 | 4, 5 |
Receive Power In OMA for Each Lane | PinOMA | dBm |
|
| 3 |
|
Difference in Receive Power in OMA between Any Two Lanes |
| dBm |
|
|
|
|
Receiver Sensitivity in OMA for Each Lane (PIN) | SOMA1 | dBm |
|
| -8.6 | 6 |
Receiver Sensitivity in OMA for Each Lane (APD) | SOMA2 | dBm |
|
| -16 | 6 |
Stressed Receiver Sensitivity in OMA for Each Lane(PIN) |
| dBm |
|
| -6.8 | 7, 8 |
Stressed Receiver Sensitivity in OMA for Each Lane(APD) |
|
|
|
| -13 | 7, 8 |
Notes:
1. The supply current includes CFP2 module’s supply current and test board workingcurrent.
2. Average launch power, each lane (min) is informative for 100GBase-LR4, not the principal indicator of signal strength.
3.The receiver shall be able to tolerate , without damage, continuous exposure to an optical input signal having this average power level
4. The average receive power , each lane (max) for 100GBASE-ER4 is larger than the
100BASE-ER4 transmitter value to allow compatibility with 100BASE-LR4 units at short distances
5. Average receive power, each lane (min) is informative and not the principal indicator
of signal strength. A received power below this value cannot be compliant; however, a value above this does not ensure compliance
6. Receiver sensitivity (OMA), each lane (max) is informative
7. Measured with conformance test signal at TP3 for BER=10-12
8. conditions of stressed receiver sensitivity test: vertical eye closure penalty for each lane is 1.8dB;stressed eye J2 jitter for each lane is 0.3UI; stressed eye J9 jitter for each lane is 0.47UI.
Ordering Information
Part Number | Description |
XYT--100G_CFP2-LR4 | CFP2 100G LR4,PIN Receiver 0~70℃ |
XYT--100G_CFP2-ER4 | CFP2 100G ER4,APD Receiver 0~70℃ |