Welcome Customer !

Membership

Sharetop Technology Co.,ltd
Free Member ·1YRS
,
Other

Main Products: 光纤传输设备

Xwboo>Products

Sharetop Technology Co.,ltdFree·1YRS

  • E-mail

    sales@xyt-tech.com

  • Phone

    +86-755-27524036

  • Address

    R1604, Bldg 11, Phase II, Tian'an Yungu, Bantian St., Longgang Dist. ,Shenzhen, 518129 ,Guangdong Prov., China

Contact Now

80km 100GBASE-ZR4 QSFP28 Optical Transceiver Module

Model
Nature of the Manufacturer
Other
Product Category
Optical Transponder Platform OTN2800
Place of Origin
City, Province
Overview
80km 100GBASE-ZR4 QSFP28 Optical Transceiver Module
Product Details

PRODUCT FEATURES


  • QSFP28 MSA compliant

  • Hot pluggable 38 pin electrical interface

  • 4 LAN-WDM lanes MUX/DEMUX design

  • 4x25G electrical interface

  • Maximum power consumption 6.5W

  • LC duplex connector

  • Supports 103.125Gb/s aggregate bit rate

  • Up to 80km transmission on single mode fiber

  • Operating case temperature: 0℃ to 70℃

  • Single 3.3V power supply

  • RoHS 2.0 compliant


APPLICATIONS


  • 100GBASE-ZR4 100G Ethernet

  • Telecom networking


DESCRIPTIONS


100G ZR4 contains 4- lane optical transmitter, 4-lane optical receiver and module management block including 2wire serial inter- face. The optical signals are multiplexed to a single-mode fiber through an industry standard LC connector. A block diagram is shown in Figure 1.


Transceiver Block Diagrams


ModSelL:
The ModSelL is an input pin. When held low by the host, the module responds to 2-wire serial communication commands. The ModSelL allows the use of multiple modules on a single 2-wire interface bus. When the Mod-SelL is "High", the module shall not respond to or acknowledge any 2-wire interface communication from the host. ModSelL signal input node shall be biased to the "High" state in the module. In order to avoid conflicts, the host system shall not attempt 2-wire interface communications within the Mod-SelL de-assert time after any modules are deselected. Similarly, the host shall wait at least for the period of the ModSelL assert time before communicating with the newly selected module. The assertion and de-asserting periods of different modules may overlap as long as the above timing requirements are met.


ResetL :


The ResetL pin shall be pulled to Vcc in the module. A low level on the ResetL pin for longer than the mini-mum pulse length (t_Reset_init) initiates a complete module reset, returning all user module settings to their default state. Module Reset Assert Time (t_init) starts on the rising edge after the low level on the ResetL pin is released. During the execution of a reset (t_init) the host shall disregard all status bits until the module indi-cates a completion of the reset interrupt. The module indicates this by asserting "low" an IntL signal with the Data_Not_Ready bit negated. Note that on power up (including hot insertion) the module should post this completion of reset interrupt without requiring a reset.


LPMode:


The LPMode pin shall be pulled up to Vcc in the module. The pin is a hardware control used to put modules into a low power mode when high. By using the LPMode pin and a combination of the Power override, Power_set and High_Power_Class_Enable software control bits (Address A0h, byte 93 bits 0,1,2).

ModPrsL:


ModPrsL is pulled up to Vcc_Host on the host board and grounded in the module. The ModPrsL is asserted "Low" when inserted and deasserted "High" when the module is physically absent from the host connector.


IntL:


IntL is an output pin. When IntL is "Low", it indicates a possible module operational fault or a status critical to the host system. The host identifies the source of the interrupt using the 2-wire serial interface. The IntL pin  is an open collector output and shall be pulled to host supply voltage on the host board. The INTL pin is deas-serted "High" after completion of reset, when byte 2 bit 0 (Data Not Ready) is read with a value of '0' and the flag field is read .


Pin Descriptions


Notes
1.Circuit ground is internally isolated from chassis ground.


Absolute Maximum Ratings


It has to be noted that the operation in excess of any individual absolute maximum ratings might cause perma-nent damage to this module.


Notes
1. Non-condensing


Operating Environments


Electricalandopticalcharacteristicsbelowaredefinedunderthisoperatingenvironment,unlessotherwisespec-ified.


    Electrical Characteristics

Optical Characteristics


100GBASE-ZR4 Operation(EOL, TOP = 0 to +70 ℃ , VCC = 3.135 to 3.465 Volts)


Notes
1,Sensitivity is specified at BER@5E-5 with FEC

EEPROM Definitions


Lower Memory Map












 - Product Specification - 

 - Sale service - 

Products damaged due to human or non-use of other causes of improper,we promises one year warranty and lifetime maintenance,but the unauthorized disassembly equipment caused damage is not covered under warranty and returned within range.
Under normal use,if there are product quality problems,or not work normally,we provide free repair or replacement service within one year;Within three years more than one year,we provide to collect the material cost,maintenance free.
Repair warranty period of three years from the freight borne by each of the parties.After three years of warranty,the material cost,maintenance,freight(refers to the product of the two-way shipping to and from)shall be borne by the user.
We promise that the product we provide can meet the performance requirements of users , and it is supplied by the user's sample request.