In order to ensure personal safety, the normal operation of the equipment, and the accuracy of the impregnated products; please read the following carefully before use. Application: Suitable for vacuum oil immersion, wax immersion and glue injection of high and low frequency transformers, inductance coils, motors, metal castings and other products. 1. The running direction of the motor should be consistent with the direction indicated by the arrow. 2. Vacuum system: use voltage 380V three-phase four-wire, equipped with ground wire. The motor uses "three-phase two-pole 0.75KW", the vacuum pump uses the direct-connected "XD-020", and the vacuum tube inlet uses a corrosion-resistant, stretch-resistant, transparent steel wire tube. The air valve uses a high-quality brass ball valve with an air check valve and an oil filter. 3. Control system: The motor is equipped with AC contactor, overload protector, and fuse. 4. Protection system: Choose "Chint" contactor to be equipped with thermal relay to protect the motor. The lighting system uses 220V energy-saving cold light lamps. 5. Product operation process: open the lid → put in the product → close the lid → start (vacuum) → open the vacuum valve "Start vacuuming, the pointer of the vacuum gauge points to 0.04, close the vacuum valve, and open the oil valve to observe the liquid level Raise the lock position》→Close the oil valve and open the vacuum valve. According to the vacuum degree required by the customer's product, the vacuum degree reaches the vacuum level to stop vacuuming. The vacuum oil immersion time is set according to the size of the product and the number of windings. →The impregnation time is up, open the intake valve to fill with air, open the oil valve, and open the vacuum box → take out the product and complete the impregnation process. 6. Troubleshooting:
Fault condition
cause of issue
elimination method
Motor doesn't rotate
①There is a problem with power supply
①Check the circuit
②The thermal protection trips
②Re-press the thermal protection reset button
③Motor burned out
③Replace the motor
The vacuum pump does not turn
Stuck or lack of oil
Oil change/Replace the vacuum pump
Can't vacuum
Air leak
①The vacuum tube is loose
②There is foreign matter in the sealing port
Seven, maintenance and maintenance: 7.1 Vacuum pump oil This series of vacuum pumps should use vacuum pump oil that meets the requirements of the SH0528-92 standard. When the ambient temperature is 0℃-10℃, use the vacuum pump oil of SIO-VG32 viscosity grade. When the ambient temperature is 10℃-40℃, use the ISO-VG100 viscosity grade. Vacuum pump oil< is="" the="" original="" 1#="" vacuum="" pump="" oil="">. When the vacuum pump is working, the oil level must be a little higher than 1/2 of the oil window height. The oil level and oil pollution should be checked frequently. It is recommended to maintain and change the oil once for 50 to 100 hours (maintain according to the working condition). 7.2 Replace the vacuum pump oil and oil filter If the oil is found to be contaminated and blackened, emulsified or thickened, the oil should be changed in time. At the same time as the oil change, the oil filter should be replaced. And the pump should be cleaned before adding new oil. Cleaning and oil change steps: 1.Turn off the power supply, and when the pump is in a hot state, unscrew the oil plug to drain the dirty oil. 2. Screw on the oil drain plug, connect the power supply and turn on the pump for 5 to 10 seconds, then stop the pump, and open the oil plug to drain the dirty oil. 3. Screw on the oil drain plug, then unscrew the oil plug, and pour the cleaning oil (No. 32 ordinary mechanical oil). See the oil in the oil window to 3/4 of the height of the oil window, then screw it on to refuel Stuffed 4. Restart the pump and run for 5-10 minutes, then stop the pump. 5. Unscrew the oil plug to drain the dirty oil. 6.Repeat steps 3, 4, and 5 until the machine oil released is transparent (the color is like new machine oil). 7. Screw on the oil drain plug. Turn on the pump for 5 to 10 seconds, then unscrew the oil plug to drain the oil. 8. Screw on the oil drain plug. Then unscrew the oil filler plug, add new vacuum pump oil, and the oil level is 3/4 of the oil window. 7.3 Replace exhaust filter If the pump temperature rises significantly, the motor current reaches or exceeds the rated current, and oily smoke is generated at the exhaust port of the pump, check whether the exhaust filter is blocked, and if it is blocked, it should be replaced in time. The exhaust pressure can be installed at the pump oil hole Gauge, check if the filter is blocked, when the pressure exceeds 0.6ar (gauge pressure), the air filter can be replaced. 7.4 Cleaning the suction filter The suction filter should be kept clean to prevent the suction speed from dropping. The suction filter is a coarse filter to prevent impurities with larger particles. Operation: After stopping the pump, first unscrew the suction nozzle connector from the suction nozzle. Then loosen the four screws on the suction nozzle, take out the suction filter in the suction nozzle, put it in the cleaning fluid (diesel or kerosene) to clean it, and then blow dry, wipe the suction nozzle clean, and inhale Put the filter into the suction nozzle, and then tighten the suction nozzle with four screws. 7.5 Cleaning the suction valve clack When there is a leak in the suction nozzle, put the suction valve disc in the suction nozzle into the cleaning liquid to clean it, and blow it with air pressure to ensure that the suction nozzle is flat and clean. 7.6 Storage If the pump is left unused for a long time, drain the vacuum pump and clean the vacuum pump with No. 32 mechanical oil. : Reuse, add vacuum pump oil) maintenance: 1. Drain the oil from the filter bottle every 24 hours. 2. Clean the sealing surface once a day. 3. Regularly check the size of the motor, voltage and current. 4. Check whether there is oil leakage or weakness in the open top rod
After-sales service commitment
1. Free maintenance and replacement of damaged parts within one year (except for man-made damage); 2. The equipment and spare parts are damaged due to man-made reasons, and maintenance fees shall be paid if they are replaced or repaired.