Welcome Customer !

Membership

Shangou Valve Co, Ltd.
Free Member ·1YRS
WenZhou,ZheJiang
Manufacturer

Main Products: valve,

Xwboo>Products

Shangou Valve Co, Ltd.Free·1YRS

  • E-mail

    59778276@qq.com

  • Phone

    0577-67975099

  • Address

    No. 430, Zhangbao North Road, Anfeng Industrial Zone, Oubei, Wenzhou, Zhejiang Province

Contact Now

ZSQRO-type three-way pneumatic ball valvePN16~PN64

Model
Nature of the Manufacturer
Manufacturer
Product Category
Ball Valve
Place of Origin
WenZhou City, ZheJiang Province
Overview
ZSQRThe standard ball core of pn16-pn64 three-way O-type pneumatic ball valve has L-type three-way double port port port and T-type three-port port port. By changing the relative angle between the ball core and the pipe, different combination control can be realized for the three branch pipe fluid.
Product Details
Product description

ZSQRThe standard ball core of pn16-pn64 three-way O-type pneumatic ball valve has L-type three-way double port port port and T-type three-port port port. By changing the relative angle between the ball core and the pipe, different combination control can be realized for the three branch pipe fluid. The T-shaped duct can connect three orthogonal pipelines, or make two of them connect and cut off the other one. L-shaped channels can only connect two orthogonal pipes or switch directions. In other words, the T-shaped channel plays the role of shunt and confluence, and the L-shaped channel plays the role of distribution. The three-way O-type ball valve is equipped with double acting or single acting RC pneumatic piston actuator (Zsh horizontal piston actuator for large diameter).

 

technical parameter
ZSQRPerformance parameters of type-A three-way O-type pneumatic ball valve pn16-pn64
Valve body formTwo open cast ball valveExecutive Agency 
Nominal diameterDN15~200typeRC, Zsh cylinder piston actuator
Nominal pressurePN1.6,4.0,6.4MPa,JIS10K,ANSI150Air source connectorRc1/8,Rc1/4,Rc1/2
Connection formFlange typeambient temperature-40℃~+80℃
Flange standard according toJB/T79.1   PN1.6MPa
JB/T79.2Concave convex surfaceANSI B16.5,JIS, B2201
Valve control modeL-type three-way double port: there are two kinds of a and B, as shown in Figure 1
T-type tee double port: there are C and D, as shown in Figure 2
Material ScienceZG25 ZG1Cr18Ni9 ZG0Cr17Ni12Mo2   -  
Medium temperatureNormal temperature type:-40℃~+180℃
fillerPolytetrafluoroethylene or r.tfe (reinforced polytetrafluoroethylene)
Valve assembly 
Type of ball valveT-type and L-type ball core
Ball core materialstainless steel
Seat materialPTFE
Ball core angle90°

 

Ordering instructions

Please provide the following information when ordering
1. Model; 2. Nominal diameter; 3. Nominal pressure; 4. Valve body material; 5. Flange connection type; 6. Ball core type (T-type or L-type); 7. Control mode (a, B, C, d); 8. Actuator model; 9. Accessories (solenoid valve, travel switch, handwheel);

 

matters needing attention

1. Be careful in installation and construction, and do not hit the valve.
2. Before installation, the ball valve should be inspected to check the specification and model, and identify whether there is damage, especially for the valve stem. Also turn a few times to see if it is skewed, because during transportation, it is easy to bump the stem. Also remove the debris in the valve.
3. When lifting the ball valve, the rope should not be tied to the hand wheel or the valve stem to avoid damage to these parts, but should be tied to the valve body.
4. The pipeline connected to the ball valve must be cleaned. Compressed air can be used to blow away iron oxide chips, mud and sand, welding slag and other impurities. These debris, not only easy to scratch the sealing surface of the ball valve, in which large particles of debris (such as welding slag), but also block the small valve, so that its failure.
5. The position of valve handle rotation should be reserved during installation. 6. The ball valve cannot be used as throttling. 7. The ball valve with transmission mechanism shall be installed vertically.