Q647f stainless steel pneumatic fixed ball valve is a two-way valve with unlimited flow direction. The middle flange is connected with studs, and the upper and lower valve stems are equipped with sliding bearings, which can reduce friction and operate labor-saving and stable.
Product overview
Q647f stainless steel pneumatic fixed ball valve is a two-way valve with unlimited flow direction. The middle flange is connected with studs, and the upper and lower valve stems are equipped with sliding bearings, which can reduce friction and operate labor-saving and stable. Under normal conditions: the valve seat seal is sealed by the spring preload when the pressure is low, and the valve seat is tightly sealed to the ball. When the pressure is high, the piston effect is formed on the valve seat, and the ball seat is pressed to the seal under the pressure of the upstream medium.
技术参数
Q647F Main technical parameters of stainless steel pneumatic fixed ball valve| Valves | Transmission mode | Transmission mode | structural style | Sealing surface | Nominal pressure(MPa) | body material |
| globe valve | 6-Pneumatic 6s-Pneumatic with manual | 4-Flange type | Fixed ball straight through | F-Fluoroplastics H-Alloy steel PPL | 1.6 2.5 4.0 6.4 | According to the valve body in the table Material code |
| Nominal diameterDN(mm) | 50-500 |
| Material code | C | P | R |
main want Zero piece | valve body | WCB | ZG1Cr18Ni9Ti | ZG1Cr18Ni12Mo2Ti |
| paddles | 2Cr13 | 1Cr18Ni9Ti | 1Cr18Ni12MoTi |
| Stem | 2Cr13 | 1Cr18Ni9Ti | 1Cr18Ni12MoTi |
| seal ring | Enhanced polytetrafluoroethylene para polybenzenes |
| filler | Polytetrafluoroethylene flexible graphite |
suitable use work condition | Applicable media | Water, steam and oil | Nitric acid | Acetic acid |
| Applicable temperature | -28℃~300℃ |
| Control type | Control type |
| Action pattern | Cut / adjust |
| Input signal | Electrical signal: 0-10mA, - 4-10ma gas signal 20-100kpa |
| Return voltage | AC220V/DC24V |
| Purified compressed air | Purified compressed air |
| Actuator | model | GT series, HY series, AW series, Zsh series, etc |
| Air source pressure | 0.4~0.7MPa |
Dimension table
Q647F External dimensions of stainless steel pneumatic fixed ball valve(mm)| Nominal diameterDN(mm) | Dimensions(mm) | Actuator model |
| 1.6MPa | 2.5MPa | 4.0MPa |
| L | D | D1 | B | Z-φD | L | D | D1 | B | Z-φD | L | D | D1 | B | Z-φD |
| 50 | 203 | 160 | 125 | 16 | 4-18 | 216 | 160 | 125 | 20 | 4-18 | 216 | 160 | 125 | 20 | 4-18 | Optional GTD / GTE AW/AWS、HY、 Zsh series actuators (the above options are for election only The specific selection is based on the actual requirements) |
| 65 | 222 | 180 | 146 | 18 | 4-18 | 241 | 180 | 145 | 22 | 8-18 | 241 | 180 | 145 | 22 | 8-18 |
| 80 | 241 | 195 | 160 | 20 | 8-18 | 283 | 195 | 160 | 22 | 8-18 | 283 | 195 | 160 | 22 | 8-18 |
| 100 | 305 | 215 | 180 | 20 | 8-18 | 305 | 230 | 190 | 24 | 8-23 | 305 | 230 | 190 | 24 | 8-23 |
| 125 | 356 | 245 | 210 | 22 | 8-18 | 381 | 270 | 220 | 28 | 8-25 | 381 | 270 | 220 | 28 | 8-25 |
| 150 | 394 | 280 | 240 | 24 | 8-23 | 403 | 300 | 250 | 30 | 8-25 | 403 | 300 | 250 | 30 | 8-25 |
| 200 | 457 | 335 | 295 | 26 | 12-23 | 502 | 360 | 310 | 34 | 12-25 | 502 | 375 | 320 | 38 | 12-30 |
| 250 | 533 | 405 | 355 | 30 | 12-25 | 586 | 425 | 370 | 36 | 12-30 | | | | | |
| 300 | 610 | 460 | 410 | 30 | 12-25 | 648 | 485 | 430 | 40 | 16-30 | | | | | |
| 350 | 686 | 520 | 470 | 34 | 16-25 | 762 | 550 | 490 | 44 | 16-34 | | | | | |
| 400 | 762 | 580 | 525 | 36 | 16-30 | 838 | 610 | 550 | 48 | 16-34 | | | | | |
| 450 | 864 | 640 | 585 | 40 | 20-30 | 914 | 660 | 600 | 50 | 20-34 | | | | | |
| 500 | 914 | 705 | 650 | 44 | 20-34 | 991 | 730 | 660 | 52 | 20-41 | | | | | |
matters needing attention
1. Be careful in installation and construction, and do not hit the valve.
2. Before installation, the ball valve should be inspected to check the specification and model, and identify whether there is damage, especially for the valve stem. Turn it a few times to see if it is skewed, because Zui is prone to bump the stem during transportation. Also remove the debris in the valve.
3. When lifting the ball valve, the rope should not be tied to the hand wheel or the valve stem to avoid damage to these parts, but should be tied to the valve body.
4. The pipeline connected to the ball valve must be cleaned. Compressed air can be used to blow away iron oxide chips, mud and sand, welding slag and other impurities. These debris, not only easy to scratch the sealing surface of the ball valve, in which large particles of debris (such as welding slag), but also block the small valve, so that its failure.
5. The position of valve handle rotation should be reserved during installation. 6. The ball valve cannot be used as throttling. 7. The ball valve with transmission mechanism shall be installed vertically.