Welcome Customer !

Membership

Wuhan Xinlaifu Hydraulic pneumatic Equipment Co. LTD
Free Member ·1YRS
,
Manufacturer

Main Products: Hydraulic System

Xwboo>Products

Wuhan Xinlaifu Hydraulic pneumatic Equipment Co. LTDFree·1YRS

  • E-mail

    wh@rexroth-hyd.com

  • Phone

    027-85849187

  • Address

    No. 28-30, Building 7, Hubei Modern Hardware & Electrical City, Dongxihu District, Wuhan

Contact Now

SBG low noise relief valve

Model
Nature of the Manufacturer
Manufacturer
Product Category
Taiwan hydraulic components
Place of Origin
WuHan City, HuBei Province
Overview
SBG low noise relief valve
Product Details

SBG low noise relief valve series features:
The SBG series is a low-noise pressure valve. It is used to control the pressure of the system and prevent the pump from exceeding the use pressure. It can be controlled and unloaded by the drain port.
Main specifications of SBG low noise relief valve series:
model
high working pressure (bar)
Pressure adjustment range (bar)
Rated flow (l/min)
Mounting screws
SBG-03-*-10
250
1:7-70
2:35-140
3:70-250
100
M12Χ40L 4PCS
(1/2Χ1-3/5)
SBG-06-*-10
200
M16Χ45L 4PCS
(5/8Χ2)
SBG-10-*-10
400
M20Χ60L 4PCS
(3/4Χ2-2/5)
SBG low noise relief valve series ordering model description:
SBG
-G
06
-1
-R
-30
Valve code
Installation form
Nominal diameter (mm)
Pressure adjustment range (bar)
Combination method
Design number
low noise
Pilot relief valve
G: Plate installation
03:10
06:20
10:32
1:7-70
2:35-140
3:70-250
L: (standard type)
Adjust the knob on the T side of the oil return port
R: (Customized products)
Adjust the knob on the side of the oil inlet P
30: Standard
32: Low bottom pressure type
Instructions for use of SBG low noise relief valve series:
Recommended viscosity
Recommended viscosity during normal work: 15~400cSt
If the valve is equipped with an oil return damper, the viscosity range must be 15~200cSt. To
Recommended oil
Any hydraulic fluid listed below can be used.
Petroleum base oil: Use oil equivalent to ISO VG32 or VG46.
Synthetic liquid: Use phosphoric acid ester liquid or polyol ester liquid. When using phosphate ester fluid, please use special fluoro rubber seal.
Aqueous liquid: Use water glycol liquid. To
Working oil temperature
The continuous working temperature is: -17 ~ +70°C
Pollution control Attention should be paid to control the pollution of hydraulic fluid, otherwise it will cause damage to the valve or shorten the service life. Please ensure that the pollution degree is: NAS 1638 -11 grade, with 25μm or finer pipeline oil filter. To
Pressure adjustment
When adjusting the pressure, loosen the lock nut and slowly turn the handle. Clockwise means the pressure rises, and counterclockwise means the pressure drops. After the adjustment, don't forget to tighten the lock nut.
The pressure is limited by the installed retaining ring. When a working pressure cannot be reached, some retaining rings can be removed. To
Oil return form
If a remote control valve is used to control the pressure, the internal volume of the return pipe is too large, and frequency vibration is likely to occur. Therefore, the length and diameter of the piping should be minimized. To
Flow selection When the flow is small, the adjustment pressure will be unstable. When using models 03 and 06, the flow rate should be greater than 5l/min, when using model 10, the flow rate should be greater than 8l/min.
SBG low noise relief valve series installation dimension drawing:
model
A
B
C
D
E
F
G
H
J
K
L
N
SBSG-G03
76
53.8
11.1
26.9
53.8
96
27
180
13.5
21
48
220.5
SBSG-G06
104
70
17
35
66.7
98.8
33.7
180
17.5
25
48
220.5
SBSG-G10
120
82.6
18.7
41.3
88.9
100
44.9
182
21.5
32
65
247.5
model
P
Q
S
T
U
V
X
Mounting surface specifications
Installation base model
SBSG-G03
206.8
157
132
104
22
106
26
ISO-6264-AR-06-2A
MF-03
SBSG-G06
206.8
157
132
104
27
123
36.5
ISO-6264-AS-08-2A
MF-06
SBSG-G10
237.5
191.5
167
135
33.5
155
47
ISO-6264-AT-10-2A
MF-10

Similar Product Recommend