(Rich Milk Powder) Spray Dryer is the most widely used process in liquid shaping technology. It is suitable for producing powder and granules solid products from solution, emulsion, soliquoid, and pumpable paste materials. Therefore, when the particle size, final moisture, bulk density and granules shape meet the accurate standard, centrifugal spray drying is a ideal drying process.
Working Principle
Liquid material is atomized through a special pressure nozzle with a high-pressure pump. Hot air enters the dryer after being adjusted by an air distributor. The material and hot air is mixed in the dryer, rapidly carries on heat and mass transfer. Powder or granular products are produced in a very short time. Products with larger particles size are discharged from the bottom of the dryer, smaller particles enter the cyclone with hot air. The exhaust gas is discharged into the air after dust removal in a scrubber. The dryers can be divided into high, middle and low-pressure spray dryers according to different pressures of atomization, while taking into account different flow fields, they are divided into co-current, fountain mode and counter-current spray dryers.
Characteristics:
1. High operational flexibility on non-adhesive or low-adhesive liquid materials.
2. Simple structure of the spray nozzle, easily used and maintained.
3. Less power consumption, low cost.
4. The hollow spherical product with big particles, good mobility and solubility.
5. Can be used to spray-cooling granulation process, such as paraffin, grease particles, special resins, etc.
This series of equipment is used in traditional Chinese medicine, food, chemical and other industries. It collects the drying and cooling of oil, sugar, fat and other heat sensitive and hygroscopic materials in a centralized manner, which can ensure the original quality of the product, good fluidity, and solvent resistance. , There is no coking and agglomeration, and the product is continuously discharged to normal temperature, which is convenient for packaging.
Specification
Type
Spray Dryer
5
25
50
100
150
200-3000
Inlet Temperature
≤ 350°C
Outlet Temperature
80-90°C
Evaporate Capacity (kg/h)
5
25
50
100
150
200-3000
Driving Force
compressed air drive
mechanical drive
Rotate Speed
25000
22000
21500
18000
18000
15000
Diameter of Atomizer (mm)
50
120
120
120
150
180-340
Heating Source
Electricity
Electricity
electricity +steam+fuel oil+coal gas
electricity +steam
electricity +steam+fuel oil+coal gas
To be solved by users
Electric-heating Power (kW)
9
45
60
81
99
Recovery Rate (%)
≥ 95
≥ 95
≥ 95
≥ 95
≥ 95
≥ 95
Installation Size
A(mm)
1000
1290
1730
2500
2800
B(mm)
2100
3410
4245
5300
6000
C(mm)
2300
4260
4645
6000
6700
φ D(mm)
1060
1800
2133
2560
2860
E1(mm)
1050
1200
1640
2100
2180
E2(mm)
1050
1200
1640
2100
2180
F(mm)
750
1000
1250
1750
1970
G(mm)
530
1700
1750
1930
2080
H(mm)
530
1300
1800
2600
3050
I(mm)
530
1550
1600
1780
1960
The following matters need to be paid attention to in daily operation of centrifugal spray dryer:
1. First turn on the centrifugal fan, then turn on the electric heating, and check if there is any air leakage. If normal, the barrel can be preheated. Because the hot air preheating determines the evaporation capacity of the drying equipment, it does not affect the quality of the material to be dried. Under the conditions, the inlet air temperature should be increased as much as possible;
2. During preheating, the valve at the bottom of the drying chamber and the discharge port of the cyclone must be closed to prevent cold air from entering the drying chamber and reducing the preheating efficiency;
3. When the inlet temperature of the drying chamber reaches 180℃~220℃, turn on the centrifugal nozzle. When the nozzle reaches a high speed, turn on the feed pump and add the material liquid. The feed volume should be from small to large, otherwise wall sticking will occur. , Until adjusted to the appropriate amount. The concentration of the material liquid should be formulated according to the temperature and nature of the material drying to ensure that the finished product has good fluidity after drying;
4. The temperature and humidity of the dried product depend on the exhaust air temperature. During operation, it is extremely important to ensure that the exhaust air temperature is a constant. This depends on the size of the feed volume, the feed volume is regulated and stable, and the outlet temperature is not changed. If the solid content and flow rate of the material liquid change, the outlet temperature will also change;
5. The product temperature is too low, you can reduce the amount of feed to increase the outlet temperature. If the temperature of the product is too high, the opposite is true. For heat-sensitive materials with lower product temperature, the amount of material can be increased to reduce the exhaust temperature, but the humidity of the product will increase accordingly;
6. The dried finished product is collected and placed in the pollinator in the lower part of the tower and the cyclone separator. The pollinator should be replaced before it is full. When replacing the pollinator, the butterfly valve above must be closed before proceeding;
7. If the dried product is hygroscopic, the cyclone separator, its pipes, and the pollinator should be wrapped with insulation material to avoid moisture absorption of the dried product.
In addition, for materials with heat sensitivity and low softening point, when the exhaust air temperature is too high, the materials will soften and the cooling air volume needs to be increased.