3.DETAIL SPECIFICATIONS
Type:KW4A-ZSW3KSF200A
Construction category:D type
Operation method:Snap Action
Configuration:Single-Pole Double-Throw (SPDT)
Terminal form:Solder Terminal
Mounting:via side mounting holes
Protection:IP40
3.1 OPERATING CHARACTERISTICS
Characteristics | Units | Standards | Note |
Actuating Force | N | 0.85 Max | Original 0.85 Max |
Release force | N | 0.1 Min | Original 0.1 Min. |
Over travel | mm | 1 Max | Original 1 Max |
Movement differential travel | mm | 0.8Max | Original 0.8Max |
Operating Position | mm | 8.8±1 | Original 8.8±1 |
Note:
Actuating Force
The force required to move the actuator from the free to the operation position
Release Force
The force allowed the mechanism to reset actuator after operation
Free Position
The position of the actuator when no external force is applied
Operating Position
The position of the actuator when contact change-over take place
Movement Differential
The distance between operation and release position


3.2 General
3.2.1 Application This specification is applied to KW4AMicro Switch used for electronic equipment.
3.2.2 Operating Temperature Range -25℃ ~ +125℃
3.2.3 Test Conditions Unless otherwise specified. The atmosphericconditions for making measurements and
tests are as follows:
Ambient temperature:15~35℃
Relative humidity:45~85%
Air pressure:86~106kPa (860~1060 mbar)
Should any doubt arise in judgment. It shall be conducted at the following conditions.
Ambient temperature:20±2℃
Relative humidity:60~70%
Air pressure:86~106kPa (860~1060 mbar)
3.3Appearance construction and dimensions
3.3.1 AppearanceSwitch shall have good finishing, and no rust crack or plating failures.
3.3.2construction and dimensionsRefer to individual product drawing.
3.4. Electrical specifications
NO. | Items | Test Condition | Criteria |
3.4.1 | Contact Resistance | Shall be measured at 1A,5V DC by voltage drop method after some operations without load. Applied position: Between terminal “C” and terminal “NO”. | 50mΩ MAX |
3.4.2 | Insulation resistance | Test voltage:500VDC, measured after 1 min ±5s Applied position: 1)Between terminal “C” and terminal “NO” 2)Between terminal and ground | 100MΩ MIN |
3.4.3 | Voltage proof | Following test voltages shall be applied for 1 min. (Cut-off current:0.5mA) 1)Between terminal “C” and terminal “NO”:1000VAC (50~60Hz) 2)Between terminal and ground: 1500V AC(50~60Hz) | Nodielectric breakdown shall occur |
3.5. Durability
No. | Item | Test Condition | Criteria |
3.5.1 | Cold | After testing at -25±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. | Contact resistance (item 4.1): 100mΩ MAX Insulation resistance (item 4.2): 50MΩ MIN Voltage proof: (item 4.3) Nodielectric breakdown shall occur. Operating characteristic (item 5.1): Within specified value . No abnormalities shall be recognized in appearance and construction。 |
3.5.2 | Dry heat | After testing at 125±2℃ for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. |
3.5.3 | Damp heat | After testing at 40±2℃ and 90-95%RH for 96 h, the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
3.5.4 | Change of temperature | After 5 cycles of following conditions the switch shall be allowed to stand under normal room temperature and humidity condition for 1h, and then measurement shall be made within 1 h. water drops shall be removed. |
3.5.5 | Salt mist | Switch shall be checked after following lest. 1) Temperature: 35±2℃ 2) Salt solution: 5±1% (solids by mass) 3) Duration: 24±1h After test, salt deposit shall be removed in running water | No remarkable corrosion shall be recognized in metal part |
3.6. Welding Performance
3.6.1 | Solder ability | Switch test under such conditions and inspect after. 1)Variable temperature range:235±5℃; 2)Dip time:3±0.5s; | The area of dip tin should capture the 95% impregnated area |
3.6.2 | Resistance to soldering heat | The switch will be inspect under such conditions below Temperature and impregnated time Trial measure | temperature(℃) | Time(s) | Slot welding method | 260±5 | 5±1 | Soldering method | 350±5 | 3±0.5 |
| All of the appearance, motor functions, electrical properties are no abnormal. |
3.7. Durability
NO. | Item | Test Condition | Criteria |
3.7.1 | Endurance (According to UL61058) | 1/4hp 250VAC Switch shall be operated according to following sequence (Test1~Test2) | Voltage | Current | Power Factor | Operation Rate | Operation Cycles | Test 1 | 125V | 17.4 A | 0.4-0.5 | 6-10cycles/min | 50cycles | Test 2 | 125V | 2.9A | 0.75-0.8 | 6-10cycles/min | 50000cycles |
5GPA 125/250VAC; 4A 30VDC Operating Cycles:50,000 cycles Operation Frequency:15~20 次/min Voltage proof:Test voltage shall be applied for 1 min(50~60Hz, Cut-off current:0.5mA) | Insulation resistance(item 4.2):50MΩ MIN; Voltage proof: Terminal and terminal:1000VAC No dielectric breakdown shall occur. Operating characteristic (item 3.1): Within 20% of specified value . 6000 cycles temperature rise: 30℃ MAX; 50000cycles temperature rise: 55℃ MAX; No abnormalities shall be recognized in appearance and construction |
3.7.2 | Endurance (According to EN61058-1 /IEC61058-1) | 5A 250VAC Operating Cycles:50,000 cycles Operation Frequency:15~20 次/min Voltage proof:Test voltage shall be applied for 1 min(50~60Hz, Cut-off current:0.5mA) | Insulation resistance(item 4.2): 50MΩ MIN Voltage proof: Terminal and terminal:750VAC Terminal and ground:1125VAC No dielectric breakdown shall occur. Operating characteristic (item 5.1): Within 10%,-30% of specified value . Temperature rise:55℃ MAX No abnormalities shall be recognized in appearance and construction |
4.DRAWING & DIMENSION

5.CIRCUIT DIAGRAM

7.PACKING
7.1 | Packing material: | Plastic box / Double-layers paper carton |
7.2 | Packing number: | 100 pieces per box;25 boxes per inner carton; 4 inner cartons per shipping cartons |
7.3 | Weight: | Gross Weight: 24kg Net Weight: 21kg |
7.4 | Size: | 500 x 530 x 240mm |