1.DETAIL SPECIFICATIONS:
This specification describes sub-miniature slide switch mainly used as small current and signal switch of electric device with the general required of mechanical and characteristics.
Type: 5MS1SWS202AVS2QES
Rating: 5A 120 VAC /2A 250VAC or 28VDC
Function: 1P2T
1.1 OPERATING CHARACTERISTICS
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
1.1.1 | Operating Force | The test point is 3mm away from the rubber handle. After three times, the test is carried out. | 300gf±100gf |
1.1.2 | Terminal Strength | In the front row of feet, any square type plus (500gf) strength test will take 15 seconds. | There are no cracks, loosening and other abnormalities in the terminals to meet the mechanical and electrical properties. |
1.1.3 | Shank strength | The force of 1Kgf is applied at the front of the handle, and the displacement should be fixed along the direction of the mark. | There is no serious deformation of the handle, and it can work normally. |
1.2 GENERAL CHARACTERISTICS
1.1.1 Application This specification is applied to 5MS1 Silde Switch used for electronic equipment.
1.1.2 Operating temperature range -30℃ + 85℃
1.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 5~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
1.3 Appearance construction and dimensions
1.3.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.3.2 Construction and dimensions Refer to individual product drawing.
1.4 ELECTRICAL SPECIFICATION
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
1.4.1 | Contact resistance | Measured at 1KHz small current (2-4VDC 100mA or less) | 10mΩ MAX |
1.4.2 | Insulation resistance | Apply a voltage of 1000V DC for 1 MIN. To following portions after which measurement shall be made. (1)Between body and terminal. (2) Between terminals. | 1000MΩ MIN |
1.4.3 | Dielectric strength | AC 1000V rms(50-60Hz) for 1 min trip Current:0.5mA (1) Between terminals. (2) Between individual terminal and frame. | Without damage to parts arcing or breakdown etc |
1.5 ENDURANCE
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
1.5.1 | Life Test | Measurement under the following test: (1)5A.120VAC resistive load-silverplated. 2A,250VAC resistive load-silverplated. 0.4A20VAC resistive load-gold plated (2)Rate of Operation: 6-8operationcycles per minute. (3)Electronics Life Test: 6,000 cycles | (1)Dielectric Strength:1000V. (2)InsulationResistance:1000M2 min. |
Mechanical Life Test: 30,000 cycles. | Contact Resistance:10mΩ Max. |
1.6. ENVIRONMENT RESISTANCE
NO. | ITEM | TEST CONDITIONS | PERFORMANCE |
1.6.1 | Resistance LowTemperature | Following the test set forthbelow the sample shall be left innormal temperature and humidity conditions for 1 hour before themeasurements are made: (1)Temperature:-40±3℃ (2)Time:96 hours | As shown in item3.4. |
1.6.2 | Resistance HighTemperature | Following the test set forthbelow the sample shall be left innormal temperature and humidity conditions for an hour before themeasurements are made: (1) Temperature:85±2℃ (2) Time:96 hours. | (1) As shown in item 3.4. (2) InsulationResistance:1000MΩ. |
1.6.3 | Resistance Humidity | Following the test set forthbelow the sample shall be left innormal temperature and humidity conditions for an hour before themeasurements are made: (1) Temperature:40±2℃ (2) Relative Humidity:90~95% (3) Time:96 hours. | (1) Contact Resistance:10 mΩMax. (2) InsulationResistance:1000MΩ min. |
1.6.4 | The SaltTesting | Following the test set forthbelow the sample shall be left innormal temperature and humidity conditions for an hour before themeasurements are made: (1) Temperature:35±2℃ (2) The ratio of salt-water:5% (3) The spray amout of salt- water:1~2ml/h. (4) Time:48 hours. | The testing standardbased on bubble,crack,And magnifyingglass with gauge. |
1.7 WELDABILITY
NO. | PERFORMANCE |
SOLDERING CONDITIONS:  Manual Soldering: Soldering Temperature | Max.350℃ | Continuous Soldering Time | Max.5 seconds |

Precautions in Handling Care should be exercised so that flux from the upper part of the printed circuit board does not adhere to the switch. |
2. DRAWING & DIMENSION:

4. CIRCUIT DIAGRAM:
