Features
Metal enclosure for Lower EMI
1310nm laser
Compliant with SFP MSA and SFF-8472 with Single LC receptacle
Digital Diagnostic Monitoring:
Compatible with RoHS
Hot-pluggable
+3.3V single power supply
Operating case temperature: Industrial : -40 to +85°C
Applications
HDMI/DVI/VGA/SDI Video Transfer
Absolute Maximum Ratings
Table 1 - Absolute Maximum Ratings
Parameter | Symbol | Min | Max | Unit |
Supply Voltage | Vcc | -0.5 | 4.0 | V |
Storage Temperature | Ts | -40 | +85 | °C |
Operating Humidity | - | 5 | 95 | % |
Note: The absolute maximum ratings exceeding the limits listed may cause permanent damage to the device.
Recommended Operating Conditions
Table 2 - Recommended Operating Conditions
Parameter | Symbol | Min | Typical | Max | Unit |
Operating Case Temperature | Standard | Tc | 0 | | +70 | °C |
Extended | -40 | | +85 | °C |
Power Supply Voltage | Vcc | 3.13 | 3.3 | 3.47 | V |
Power Supply Current | Icc | | | 200 | mA |
Data Rate | | 3 | | | Gbps |
Optical and Electrical Characteristics
Table 3 - Optical and Electrical Characteristics
Parameter | Symbol | Min | Typical | Max | Unit | Notes |
Transmitter |
Centre Wavelength | λc | | 1310 | | nm | |
Spectral Width (RMS) | Δσ | | 2 | | nm | |
Average Output Power | Pout | +4 | -3 | | dBm | 1 |
Spectrum Bandwidth(-20dB) | SMSR | 30 | | | dB | |
Extinction Ratio | ER | 9 | | | dB | |
Optical Rise/Fall Time (20%~80%) | tr/tf | | | 130 | ps | |
Data Input Swing Differential | VIN | 350 | | 1800 | mV | 2 |
Input Differential Impedance | ZIN | 90 | 100 | 110 | Ω | |
TX Disable | Disable | | 2.0 | | Vcc | V | |
Enable | | 0 | | 0.8 | V | |
TX Fault | Fault | | 2.0 | | Vcc | V | |
Normal | | 0 | | 0.8 | V | |
| Low | | | 0.8 | V | |
Notes:
1. The optical power is launched into SMF.
2. PECL input, internally AC-coupled and terminated.
Timing and Electrical
Table 4 - Timing and Electrical
Parameter | Symbol | Min | Typical | Max | Unit |
Bite Rate | BR | 155 | | 3000 | Mbps |
Tx Disable Negate Time | t_on | | | 1 | ms |
Tx Disable Assert Time | t_off | | | 10 | µs |
Time To Initialize, including Reset of Tx Fault | t_init | | | 300 | ms |
Tx Fault Assert Time | t_fault | | | 100 | µs |
Tx Disable To Reset | t_reset | 10 | | | µs |
Serial ID Clock Rate | f_serial_clock | | | 400 | KHz |
MOD_DEF (0:2)-High | VH | 2 | | Vcc | V |
MOD_DEF (0:2)-Low | VL | | | 0.8 | V |
Diagnostics
Table 5 – Diagnostics Specification
Parameter | Range | Unit | Accuracy | Calibration |
Temperature | 0 to +70 | °C | ±2°C | Internal / External |
-40 to +85 |
Voltage | 3.0 to 3.6 | V | ±3% | Internal / External |
Bias Current | 0 to 100 | mA | ±10% | Internal / External |
TX Power | -6 to 0 | dBm | ±2dB | Internal / External |
Pin Diagram

Pin Descriptions
Pin | Signal Name | Description | Notes |
1 | VEE_TX | Transmitter Ground | |
2 | TX FAULT | Transmitter Fault Indication(Active High, Open drain) | Note 1 |
3 | TX Disable | Transmitter Disable | Note 6 |
4 | Mod-Def2 | Transmitter Ground | |
5 | Mod-Def1 | I2C Clock | Note 2 |
6 | Mod-Def0 | I2C Data | Note 2 |
7 | Rate Select | Not connected | |
8 | RX_LOS | Loss of Signal(Active High, Open drain) | Note 3 |
9 | VEE_RX | Receiver ground | |
10 | VEE_RX | Receiver ground | |
11 | VEE_RX | Receiver ground | |
12 | RD- | Inv. Received Data Out | Note 4 |
13 | RD+ | Received Data Out | Note 4 |
14 | VEE_RX | Receiver ground | |
15 | VCC_RX | Receiver Power Supply | |
16 | VCC_TX | Transmitter Power Supply | |
17 | VEE_TX | Transmitter Ground | |
18 | TD+ | Transmit Data In | Note 5 |
19 | TD- | Inv. Transmit Data In | Note 5 |
20 | VEE_TX | Transmitter Ground | |
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) They should be pulled up with a 4.7k~10kΩ resistor on the host board. The pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
3) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage between 2.0V and Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to less than 0.8V.
4) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES or Reclocker.
5) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.
6) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:
Low (0 to 0.8V): Transmitter on
(>0.8V, < 2.0V): Undefined
High (2.0 to 3.465V): Transmitter Disabled
Open: Transmitter Disabled
Host Board Power Supply Requirements

Typical Application Circuit

Mechanical Dimensions
