Welcome Customer !

Membership

Guangdong Komeg Industrial Co., Ltd.
Free Member ·1YRS
DongGuan,GuangDong
Manufacturer

Main Products: Environmental Test Chambers

Xwboo>Products

Rapid Temperature Change Chamber /ESS-3000L

Model
Nature of the Manufacturer
Manufacturer
Product Category
ESS Environment Stress Screening
Place of Origin
City, Province
Overview
Rapid temperature change chamber are very powerful climatic chambers used to perform hot and cold cycles with steep temperature gradients(from 3 to 15C/min depending on the temperature ranges)
Product Details

Rapid Temperature Change Chamber / 3000 L

Standards Implemented and met

GB-2423.1-2008(IEC68-2-1)Test A: Cold Test

GB-2423.2-2008(IEC68-2-2)Test B: Dry Heat Test

GJB360.8-2009(MIL-STD.202F) Heat Aging Test

GJBl50.3-2009 (MIL-STD-810D) high temperature test method.

GJBl50.4-2009 (MIL-STD-810D) low temperature test method.

GB2423.3-2008 (IEC68-2-3) Test Ca: Constant damp heat test method.

GB2423.4-2008 (IEC68-2-30) Test Db: Alternating damp heat test method.

GJBl50.9-2009(MIL-STD-810D) Damp heat test chamber technical conditions

Main Technical
Water-cooled. The specifications measurement in the environment temperature at + 25 ℃ without load
volume3000 L
1. Temperature
1.1 Temp. range-70℃~+150℃
1.2 Temp. deviation≤±2.0℃
1.3 Temp. fluctuation±0.5℃
1.4 Heating up rateFrom -40℃ to +85℃, linear, 15℃/min
1.5 Cooling rateFrom -40℃ to +85℃, linear, 15℃/min
2. Humidity
2.1 Humidity range20%R.H.~98%R.H
2.2 Humidity range
2.3 Humidity deviation±3.0%RH(>75%RH)±5.0%RH(≤75%RH)
2.4 Humidity fluctuation±2.0%RH
3. Floor capacity300KG/m2
4. Full load

10 PV Modules to be loaded in a vertical orientation.

Single panel max. size of 2000*1000*50mm.

Total weight of 300KG.

Temperature and humidity performance test is in accordance with the relevant provisions of the IEC60068 -3 standard

measurement; sensor placed in the unit outlet.According to national test standard: GB/T 5170.2, use 9 test point

calibration, as below:

Body Structure

Overall structure and chamber is composed of three parts as below.Insulation box, separate refrigeration units, and electrical

control cabinet.

1. Body dimensions

Workplace volume: W 1000 × H 1500 × D 2000 mm,Exterior size: W 1500 × H 3500 × D 4350 mm,

2. Insulation Box

※ wall material: high-quality carbon steel※ inner wall material: SUS304 # matte stainless steel plate※

Insulation materials:

100mm rigid polyurethane foam insulation layer + glass fiber.

3. DoorDouble door (according to design), with observation window (the size depend on final design)
4. Lighting DeviceMoisture-proof lighting, with explosion-proof lampshades.
5. Cable portφ100mm*1 located on both side of chamber, with rubber stopper
6.Electric control boxTotal power circuit breaker, over-temperature protection.
7. Control model

This device is Cascade compression refrigeration

We use intellectual cooling control: PID will control solenoid-valve and heater on/off to adjust cooling or heating capacity according to temperature and loading requirements and status inside the chamber. Only cooling or only heating will be activated to get temperature balance to save energy
8. HeatingHigh quality nickel-chromium alloy wire electric heaters,Non-contact control mode(SSR)
9. Water outlet hole Available for drain the condensate water
10. Water purifierPure water device, 1 pcs, please provide 1 ~ 2 kg/cm2 tap water
11. Water supply systemPump to enhance automatic water supply
12. HumidificationStainless steel corrosion-resistant electric evaporative humidification
13. Humidity sensorHigh accuracy Vaisala electronic humidity sensor

Similar Product Recommend