-
E-mail
export@wedhb.com
- Phone
-
Address
Changjie North Road, Chagnsha City, Hunan Province, China
Membership
Help
Welldone Environmental Protection Equipment (Changsha) Co., Ltd.Free·1YRS
export@wedhb.com
Changjie North Road, Chagnsha City, Hunan Province, China
With the development of science and technology, automation increasingly improved. The production technology from flame cutting to plasma cutting has been continuously improved and popularized. And these efficient production technologies have also brought more and more serious pollution problems, resulting in more dust in the workplace. Dust remover is imperative before cutting technology is effectively improved. The cutter on the cutting frame can be installed more, and the cutting ability and cutting thickness constantly improve, more harmful smoke and gas produced by the laser/flame cutting. The efficiency of laser/plasma cutting and the continuous increase of cutting thickness have made the cutting amount of smoke to an alarming extent. Choose a removal system with good dusting effect and low cost, it is not only the initial investment of the equipment, but also the stability and energy saving that the system runs. We can provide the most effective solution according to the actual situation of the customer, and minimize the harm of cutting smoke.
Welldone industrial dust collection systems solution:
1. Air door type dust remover system for table cutting machine
The wind door type dust remover system adopts many technical innovations, Smoking effect is remarkable, installation and maintenance is simple, economic energy saving. The effect of cutting smoke absorption and purification depends on the design of the dust cutting table. In order to maximize the smoke absorption rate, the dust removal cutting table adopts modular design, no matter what your cutting range is, we can attain the size you need by modularity. The inside of the gantry cutting table is divided into separate zones for individual section vacuuming, each independent area has independent valve and it is controlled by cutting machine to automatically open the air valve in the area where the cutting is done to remove dust. Dust collecting boxes are installed in each suction area in the lower part to facilitate hoisting and dumping of dust.
Air door type dust removal system is used in the desktop laser cutting machine、plasma cutting machine, flame cutting machine, etc.

2. The side suction type dust remover system for gantry cutting machine
The side suction type dust remover system is to place a square suction duct on the side of the cutting platform, it has a suction outlet that may be moved with the cutter. there is a blow-off nozzle and suction outlet with a small axial fan on the other side of the cutting platform. It has a suction outlet that can be moved with the cutter, The suction outlet is also fixed on the cutting machine and it is kept in line with the cutting head. The lower part of the cutting platform is a suction pipe with a vertical panel, which is always maintained only in the limited width of the cutting, when the smoke is produced. In the work, the sealing belt is under the pressure of the pipe, tightly attached to the square suction duct, which acts as a seal. There are two rollers in the air inlet, and the seal belt is lifted up here so that the smoke can be sucked through the air suction duct, and finally the dust removal equipment is filtered and purified.
The side suction type dust removal system is used for the gantry plasma, flame cutting machine.
| It is recommended to adopt d suction type dust removal system when the cutting width of cutting machine is less than 5 meters. | |
![]() | The effective cutting width of cutting machine is less than 5 meters, and the suction type dust removal system is recommended. |
3. Pipe cutting dust removal system
Pipe cutting processing is mainly cutting pipe and processing line. The pipe material is generally long length, and the pipe wall is thicker, resulting in a large amount of smoke. This kind of cutter is generally used to remove dust directly from the cutter port, wen the cutting head cut the groove more, the smoke overflow will be more, at this time it is better to add a suction hood to the cutting head to ensure the dust removal effect.
The pipe cutting and dust removal system is used in plasma phase line cutting machine, square pipe cutting machine, etc.

We accept customization according to actual working condition.
Technical Data | |||||
Model | WLC-4YT | WLC-6YT | WLC-9YT | WLC-12YT | WLC-16YT |
Max. Airfolw | 4000m³/h | 6000m³/h | 9000m³/h | 12000m³/h | 16000m³/h |
Filter Cleaning Method | Pulse jet/Automatic | Pulse jet/Automatic | Pulse jet/Automatic | Pulse jet/Automatic | Pulse jet/Automatic |
Power Supply | 380V/3PH/50HZ | 380V/3PH/50HZ | 380V/3PH/50HZ | 380V/3PH/50HZ | 380V/3PH/50HZ |
Motor Power | 5.5kw | 7.5kw | 11kw | 15kw | 18.5kw |
Filtering Efficiency | 99.9% | 99.9% | 99.9% | 99.9% | 99.9% |
Filter Elements | 4-Φ324* 860mm | 6-Φ324* 860mm | 9-Φ324* 860mm | 12-Φ324* 860mm | 16-Φ324* 860mm |
No. of Filter Cleaning Valve | 4 | 6 | 9 | 12 | 16 |
Dustbin Volume | 40L | 60L | 60L | 114L | 2* 81L |
Noise Level | <75dB(A) | <75dB(A) | <75dB(A) | <80dB(A) | <85dB(A) |
Compressed Air Requirement | 0.5-0.6MPa | 0.5-0.6MPa | 0.5-0.6MPa | 0.5-0.6MPa | 0.5-0.6MPa |
Inlet Size | Φ350mm | Φ380mm | Φ450mm | Φ550mm | Φ600mm |
Dimensions | 1100* 1100* 2600mm | 1200* 1320* 2720mm | 1450* 1450* 2720mm | 1550* 1690* 2870mm | 1980* 1690* 2870mm |
Options | Explosion-proof | Explosion-proof | Explosion-proof | Explosion-proof | Explosion-proof |
Frequency conversion | Frequency conversion | Frequency conversion | Frequency conversion | Frequency conversion | |
Wireless remote control | Wireless remote control | Wireless remote control | Wireless remote control | Wireless remote control | |
Activated carbon filtration | Activated carbon filtration | Activated carbon filtration | Activated carbon filtration | Activated carbon filtration | |
Other bigger air volume, as you need, we can customize it.
● 3 Years quality warranty for motor and fan. 1 year for filter
● See specific product 20~40 days after reception of payment meet shipment condition
● Payment 30% deposit by T/T, 70% balance before shipment
● Packaging Details:with wrapping film on pallet
● Port: Shanghai/Guangzhou/Shenzhen