Welcome Customer !

Membership

ACE METER TECHNOLOGY CO.,LIMITED
Free Member ·1YRS
DaLian,LiaoNing
Manufacturer

Main Products: Flowmeter

Xwboo>Products

Easy Install Tap Water Electromagnetic Flow Meter

Model
Nature of the Manufacturer
Manufacturer
Product Category
Electromagnetic Flow Meter
Place of Origin
City, Province
Overview
With the continuous improvement of automation technology level and the requirement of trade settlement measurement in water supply industry, tap water electromagnetic flow meter has been more and more widely used and promoted, and its application in water supply industry has been widely recognized. The tap water electromagnetic flow meter has the characteristics of high measurement accuracy, good stability and wide application range, which provides a powerful technical guarantee for the realization of automatic con......
Product Details

easy install tap water electromagnetic flow meter


With the continuous improvement of automation technology level and the requirement of trade settlement measurement in water supply industry, tap water electromagnetic flow meter has been more and more widely used and promoted, and its application in water supply industry has been widely recognized. The tap water electromagnetic flow meter has the characteristics of high measurement accuracy, good stability and wide application range, which provides a powerful technical guarantee for the realization of automatic control and fair trade measurement in the water plant and plays a huge role. In the future, with the continuous improvement of technology, application and cost performance, the tap water electromagnetic flow meter will be more and more widely used in the water supply industry.


easy install tap water electromagnetic flow meter

easy install tap water electromagnetic flow meter (2)


Measure Medium

Water,Sewage,Acid,Alkali,Slurry,Milk

Nominal diameter

15-500mm

Degree of accuracy

±0.5%R

Medium conductivity

≥5uS/cm,Actual conductivity≥30uS/cm

Nominal pressure

1.0MPa

1.6MPa

2.5MPa

4.0MPa

DN15-DN500

DN15-DN500

DN15-DN500

DN15-DN50

Highest medium temperature

Compact type

+80℃

Remote type

CR chloroprene rubber liner (CR)

+80℃

Polytetrafluoroethylene lining(F4)

+120℃

Politef lining(F46)

+120℃

Teflon(PFA)

+180℃

Fluorosilicone rubber(FVMQ)

+250℃

Output signal

4-20mA;Pulse/Frequency 2kHz(Default),5KHz(Max)

Supply voltage

110/220VAC(100-240VAC),50Hz/60Hz;24VDC ±10%

Communication

RS-485,Support standard Modbus-RTU protocol;GPRS

Electrode material

Stainless steel 316L,Hastelloy C,Hastelloy B,titanium, tantalum, platinum

Level of protection

Remote type

IP68,IP65

Compact type

IP65


Solutions in the use of easy install tap water electromagnetic flow meter

The tap water electromagnetic flow meter has high stability, and the instrument equipment itself seldom breaks down. However, due to the change of environmental conditions or the limitation of installation conditions, there are also some problems or faults, which should be solved or avoided, mainly as follows:

1. the installation conditions of the flow meter are not met, and the requirements of the tap water electromagnetic flow meter for the straight pipe section of the pipeline are high, which can be met as much as possible in the design of the new water plant. For the reconstruction or installation of the old water plant, the above conditions become almost harsh. Therefore, the stability of measurement is affected. The solution is to install rectifiers to improve the flow characteristics.

2 .the velocity of measured water is too low, which affects the accuracy of measurement. Especially for the tap water electromagnetic flow meter installed at the boundary of some areas, the flow rate is too low due to the small pressure difference at the end of the pipe network of the regional company. The solution is to open the valves on both sides of the boundary as much as possible.

3. there is gas in the pipeline water, which causes measurement fluctuation and greatly affects the stability. The solution is to find the source of gas and solve it. If necessary, install exhaust valve in the pipeline.

4 .the converter of easy install tap water electromagnetic flow meter is damaged by lightning stroke, so that it can not be measured. The solution is to install corresponding arresters at the signal input terminal, excitation current input terminal and working power supply terminal of the converter.


easy install tap water electromagnetic flow meter (3)

easy install tap water electromagnetic flow meter (4)

easy install tap water electromagnetic flow meter (5)

easy install tap water electromagnetic flow meter (6)


easy install tap water electromagnetic flow meter