Welcome Customer !

Membership

Jinan Focor Machinery Co.,Ltd
Free Member ·1YRS
JiNan,ShanDong
Manufacturer

Main Products: Loader|Truck|Hydraulic Pump

Xwboo>Products

Jinan Focor Machinery Co.,LtdFree·1YRS

  • E-mail

    sales@focormach.com

  • Phone

    86-531-88802487

  • Address

    410, Fenghuang Road, Gaoxin District, Jinan City, Shandong Province, China.

Contact Now

Jumbo Boomer

Model
Nature of the Manufacturer
Manufacturer
Product Category
Drilling Jumbo
Place of Origin
City, Province
Overview
Jumbo Boomer
Product Details
Brief Introduction

Name: Jumbo boomer

Model: FK10-1BCDL

Power of Diesel engine: 50 KW

Power of Electric motor: 42.5 KW

Section (b×h): 2×2~3.5×3.5 m

Dimensions: 8300×1350×2650 mm

Product Introduction

FK10-1BCDL jumbo boomer is mainly used to drill blast holes for tunneling constructions in mining, metallurgy, water and electricity, railway, highway engineering, etc. This series use all hydraulic drive, with high efficiency and speed which can be 0.8-2.5 m/min. The advanced hydraulically controlled drilling system, which is safe and simple to operate, incorporates the auto stop and anti-jamming function, auto-stop at end-point, auto wash. This jumbo has a small body, runs with the wheels, can reach a speed of 20km/h Working with electric motor can improve the working environment a lot, reduces noise, dust and energy consumption. The flexible hydraulic rock drill can work on the section, roof, side and floor. The jumbo can not only drill blast hole,according to the the basis of section, it also can drill bolt hole conveniently with our patent impeller.

Configuration And Technical Parameters

Item

Parameter

Body

Overall size (L×W×H)

8300×1350×2650 mm

Hole diameter

φ33~φ102

Drill pipe length

3050 mm

Hole depth

2.7 m

Drilling speed

0.8~2 m/min

Section (W×H)

2×2~3.5×3.5 m

Climbing capability

14%

Total weight

≈7000 kg

Bottom

Min. turning radius

2500 m

Running speed

≤20 km/h

Climbing capability

8°

Joint

inner35°, outer35°

Up and down

up55°, down16°

Rotation angle

positive180°, negative180°

Pitching

down105°, up15°

Compensation

1500 mm

Thruster

Pitching

down105°, up15°

Swing angle

inner45°, outer45°

Total length

4150 mm

Hole depth

2700 mm

Max. Propulsion

9000 N

Impact oil pressure

14~16 MPa

Impact flow

30~45 L/min

Torque

60~260 N·m

Impact energy

100~200 J

Impact frequency

34~67 Hz

Rotating speed

200~400 r/min

Hydraulic system

Impacting loop pressure

16 MPa

Drill pipe rotation loop pressure

15 MPa

Compensation loop pressure

10 MPa

Boom loop pressure

20 MPa

Propulsion loop pressure

16 MPa

Leg extension loop pressure

21 MPa

Running loop pressure

20 MPa

Air system

Tank air pressure

0.03 MPa

Rock drill air pressure

0.4 MPa

Water system

Rock drill water pressure

(≥)1.2 MPa

Colder water pressure

(≤)0.6 MPa

Electric system

Installed power

42.5 KW

Supply voltage

380 V

Electric motor rotation speed

1470 r/min

Main Features

FK10-1BCDL 1040

Product Qualification


证书

Other Underground Mining Machines We Supply

image039_1

Latest News - Preparation work before start the jumbo

6.2

6.2.1 Whether tightening of various soft pipes, operating handle, electric cable, water tube, connector, crawler, drill rod, drill head bit, screw bolt, screw nut, Whether any blocking, impact and miscellaneous articles of various running position.

6.2.2 Check various parts before start the jumbo

6.2.2.1 Oil level of oil tank (observe oil level line of the oil tank), Oil level of glass cup of the lubrication oil atomizer of the rock drill.

6.2.2.2 Oil level of engine oil (observe oil level line of the oil tank), and the level of engine water tank cannot be lower than the overflow opening.

6.2.2.3 The operation handle is at “0”position.

6.2.2.4 Whether loosing of screw bolt and nut, especially, the fastening bolt of the rock drill jumbo and the screw bolt on the guide body of the drill bit holding device should be fastened.

6.2.2.5 Whether rational of degree of tensioning of steel wire rope of the thruster and travel crawler.

6.2.2.6 Whether clean and normal of component of drive sprocket wheel of travel crawler, slide rail of directive wheel, caterpillar joint, buffer tension spring.

6.2.2.7 Supply power and check whether normal lighting of front and rear truck light.

6.2.2.8 Confirm that the hand throttle is in idle position, start the engine, see if the parameters are normal, rotate the hand throttle slowly, control the engine speed at about 1500rmin (strictly forbid more than 1800rmin, it will injure the jumbo!).

6.2.2.9 Check all pressure gauges.

6.2.2.10 Open water supply switch and observe whether normal of water supply pump, the water pressure is 0.8~1.5MPa and smooth water supply of drill rod and drill bit.

6.2.2.11 Check whether normal of actions of various oil cylinders, whether any blocking occurs.

6.2.2.12 Before operate various actions first support the leg, operate actions after the machine in stable condition.

6.3 Lubricate various running positions of the drilling jumbo

6.3.1 Molybdenum disulphide grease is applied on shank of drilling jumbo, spline impact connection and connection sleeve and drill rod connection.

6.3.2 Molybdenum disulphide grease is applied on slide plate and guide rail of drilling jumbo, soft pipe roller and pallet.

6.3.3 Fully filling lubricating oil to various positions following requirement in instruction manual of drilling jumbo.

Running mechanism of right and left crawler belt are completely two independent structures. The crawler belt running mechanism is composed of crawler belt component and running ground drive mechanism.

The crawler belt parts are composed by crawler belt 10, crawler belt tensioning device 8,thrust wheel 9, guide.

11. Driving parts are composed by a hydraulic brake, a walking motor 5 and driving wheel 6, all of them are fixed on the crawler belt frame 7. The left and right crawler belt frames are welded on the left and right side of the carriage.

The principle of running of crawler belt of the machine is as follows:

The running of machine crawler belt is driven by the ground drive mechanism. When the hydraulic system supplies oil to the ground drive mechanism, the ground drive mechanism provide power to the traction wheel and drive the crawler belt and advance, retreat and turn of the drill jumbo. When the hydraulic system not supplies oil to the ground drive mechanism, the ground drive mechanism lost pressure and stopped.

The degree of loose or tightening of crawler belt is adjusted by the take‐up oil cylinder and, the grease is injected into the nozzle tip by high pressure oil gun. The weight of the jumbo machine is supported by 5 thrust wheels under the crawler belt frame. To prevent loose of crawler belt, chain supporting plate and side guard plate constitute the walking shield, fixed above the hydraulic motor.


Similar Product Recommend