PA A Series Variable Displacement Piston Pumps Under the conditions of pressure 16 MPa (2320 PSI) and speed 1800 r/min, the volumetric efficiency is over 98% and the overall efficiency is over 90%.
Product Details
Plastic machinery piston pumps A
PA A Series Variable Displacement Piston Pumps Under the conditions of pressure 16 MPa (2320 PSI) and speed 1800 r/min, the volumetric efficiency is over 98% and the overall efficiency is over 90%.
Name
A Series Variable Displacement Piston Pumps
Series
Series A
Sizes
10 16 22 37 45 56 70 90 100 145
Nominal Pressure
210 bar
Maximum Pressure
280 bar
Operation Mode
Open Circuit
Geometric Displacement cm3/rev
Minimum Adj. Flow cm3/rev
Operating Presure MPa (PSI)
Shaft Speed Range r/min
Approx. Mass kg (lbs.)
Model Numbers
(cu. in. /rev)
(cu. in.
/rev)
2
1
Max.
Min.
Flange Mtg.
Foot Mtg.
Rated
Intermittent
A10
10.0 (.610)
2 (.122)
16 (2320)
21 (3050)
1800
600
5.1 (11.2)
A16
15.8 (.964)
4 (.244)
16 (2320)
21 (3050)
1800
600
16.5 (36.4)
18.7 (41.2)
A22
22.2 (1.355)
6 (.366)
16 (2320)
16 (2320)
1800
600
16.5 (36.4)
18.7 (41.2)
A37
36.9 (2.25)
10 (.610)
16 (2320)
21 (3050)
1800
600
28.0 (61.7)
32.3 (71.2)
A45
45(2.75)
11(.671)
16 (2320)
21 (3050)
1800
600
28.0 (61.7)
32.3 (71.2)
A56
56.2 (3.43)
12 (.732)
16 (2320)
21 (3050)
1800
600
35.0 (77.2)
39.3 (86.7)
A70
70.0 (4.27)
30 (1.83)
25 (3630)
28 (4060)
1800
600
58.5 (129)
70.5 (155)
A90
91.0 (5.55)
56 (3.42)
25 (3630)
28 (4060)
1800
600
72.5 (160)
93 (205)
A100
100(6.1)
62 (3.78)
21 (3050)
21 (3050)
1800
600
72.5 (160)
93 (205)
A145
145 (8.85)
83 (5.06)
25 (3630)
28 (4060)
1800
600
92.5 (204)
117.5 (259)
1:Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.
2:Care should be taken in cases of used at a higher pressure than the rated pressure, because operating terms may be restricted. For example, if used as per maximum illustrated operating conditions, intermittent time at maximum flow is restricted to under 1/5 of one cycle time and under six seconds simultaneously. Conditions may vary according to the actual working pressure and delivery (inclination angle of the swash plate). Consult factory or POOCCA sales representative for further information.
3:The table above shows specifications for using petroleum based oils. Pumps (customized design) for special fluids are also available. Their operating pressure and maximum shaft speed however differ from the values in the table above depending on the fluid type.
Range of operating temperature and viscosities may differ from those of petroleum based oils due to their characteristics.
High efficiency:Under the conditions of pressure 16 MPa (2320 PSI) and speed 1800 r/min, the volumetric efficiency is over 98% and the overall efficiency is over 90%.
Accomplishment of energy-saving:Because the overall efficiency is high and the cut-off characteristics is sharp, thus the input power may be saved.
Low noise level:In the "A16" pump, the noise level is as low as 57.3 dB(A) [at the full cut-off pressure 21 MPa (3050 PSI) with speed 1500 r/min one metre (3.3 ft.) horizontally away from pump head cover.]
Low noise level:Because of small power loss, it is possible to reduce the rise in oil temperature. Accordingly, capacity of a reservoir can be reduced.
A series plunger pump has the characteristics of high volumetric efficiency, energy saving, various control methods and strong flexibility.
The company was established in 2012.
We have a very professional technical team to solve problems for your hydraulic pump.
Our sales will reply to your product inquiries within 1 hour
Quality is guaranteed.
Warranty: 12 months
USING:
Notice:
When installing the hydraulic pump, the oil inlet of the pump must be placed upward.
When using this pump for the first time, inject clean hydraulic fluid into the pump through the oil inlet.