Welcome Customer !

Membership

Cixi Fly Pipe Equipment Co.,ltd
Free Member ·1YRS
,
Other

Main Products: 阀门

Xwboo>Products
Product Categories

Cixi Fly Pipe Equipment Co.,ltdFree·1YRS

  • E-mail

  • Phone

  • Address

    Buiding 289,XingGongYuan,North 3-Ring RD,ZongHan Street,Cixi,China

Contact Now

Rising Stem Gate Valves

Model
Nature of the Manufacturer
Other
Product Category
Place of Origin
City, Province
Overview
Rising Stem Gate Valves
Product Details

Rising Stem Gate Valves

Cast Steel Bolted Bonnet Gate Valves (Rising Stem) 150lb – 2500lb

40_0-2-largeRising stem gate valve

Parts and Material List

Parts No.Parts NameMaterials
WCB/Trim1WCB/Trim5WCB/Trim8CF8/304CF8M/316
1BodyASTM A216 WCBASTM A351 CF8ASTM A351 CF8M
2GasketSoft iron+Graphite or 304+Graphite304+Graphite316+Graphite
3Seat ringA105+13CrA105+STLA105+STLASTM A351 CF8ASTM A351 CF8M
4GateASTM A216 WCB+13CrASTM A216WCB+STLASTM A216 WCB+13CrASTM A351 CF8ASTM A351 CF8M
5StemASTM A182 F6aASTM A182 F304AST A182 F316
6Backseat bushingASTM A182 F6aASTM A351 CF8ASTM A351 CF8M
7PackingGraphiteGraphiteGraphite
8GlandASTM A182 F6aASTM A182 F304ASTM A182 F316
9Gland eyeboltASTM A193 B7ASTM A193 B8ASTM A193 B8M
10Eyebolt nutASTM A194 2HASTM A193 8ASTM A194 8M
11Eyebolt pinASTM A36304SS316ss
12Gland flangeASTM A216 WCBASTM A351 CF8ASTM A351 CF8M
13Bonnet boltAST A193 B7ASTM A193 B8ASTM A193 B8M
14Bonnet nutASTM A194 2HASTM A194 8ASTM A194 8M
15BonnetASTM A216 WCBASTM A351 CF8ASTM A351 CF8M
16NippleCarbon steelCarbon steelCarbon steel
17Stem nutASTM A439 D2ASTM A439 D2ASTM A439 D2
18Yoke sleeve nutCarbon steelCarbon steelCarbon steel
19Hand wheelDuctile ironDuctile ironDuctile iron
20Hand wheelnutCarbon steelCarbon steelCarbon steel
21Set screwASTM A193 B7ASTM A193 B7ASTM A193 B7

NOTE: The chart above only lists out some common composition of parts. We may provide other different parts material composition according to the customer’s request or the actual valve working condition.

Features

  • Seal-welded seats
  • Bosses for taps & bypass
  • Graphite packing
  • Ring Joint Bonnet gaskets Class 600-2500
  • Fully guided, wedge
  • Fugitive emission tested

Options

  • Alternate Trims
  • NACE MR-01-75
  • Mounting Pads for Actuation
  • Pressure Seal Bonnets Class 600-2500
  • Aluminum Bronze and Bronze Trims for Marine Service

Standards

  • API-600
  • ANSI B16.34
  • ANSI B16.10
  • ANSI B16.5
  • ANSI B16.25
  • ANSI B16.47
  • API-598

OTE: The chart above only lists out some common composition of parts. We may provide other different parts material composition according to the customer’s request or the actual valve working condition.

Structure dimensions

CLASS/SIZE150 -L300 -L600 -L900-L
RFBWRF/BWRTJRF/BWRTJRF/BWRTJ
2178216216232292295368371
2 1/2191241241257330333419422
3203283283298356359381384
4229305305321432435457460
5254381381397508511559562
6267403403419559562610613
8292419419435660664737740
10330457457473787791838841
12356502502518838841965968
1438157276277888989210291038
1640661083885499199411301140
1843266091493010921095
20457711991101011941200
245088131143116513971407
2655986412451270
2861091413461372
3061091413971422
3271196515241553
34762101616261654
36711101617271756

1. Gate valve are normally used for on-off service and are not recommended for throttling service.

2. Gate valves are normally installed in horizontal pipe runs with the stem vertical. They can also be installed in vertical or horizontal pipe runs with the stem other than vertical, but may require special construction depending on valve size, service conditions and materials. WHEN PURCHASING VALVES FOR OTHER THAN NORMAL INSTALLATION, THE VALVE ORIENTATION SHOULD BE SPECIFIED.

3. Flexible or split wedges are recommended for service above 500 ℉ to avoid wedge binding due to thermal expansion. This may occur if the valve is closed when cold, and then heated to operating temperature.

4. Threaded seat rings should be lock welded to the body when used in high velocity (turbulent) or thermal cycling services to avoid loosening. Please specify.

5. After closing a gate valve with sufficient force to develop shutoff, the stem should be backed off slightly (1/8 to 1/4 turn) to relieve stem load. This will enable the stem to expand slightly without binding or damaging the valve and will not affect shutoff.