Welcome Customer !

Membership

ACEPOM GROUP
Free Member ·1YRS
,
Other

Main Products: 检测仪器

Xwboo>Products
Product Categories

ACEPOM GROUPFree·1YRS

  • E-mail

    shawn@acepom.com

  • Phone

    +86-0523-84268368

  • Address

    68 SOUTH RENMIN ROAD, JINGJIAGN,JIANGSU,CHINA.

Contact Now

ACEPOM 520 Laser Leveling Instrument for Wind Power Tower Tube

Model
ACEPOM520
Nature of the Manufacturer
Other
Product Category
Place of Origin
City, Province
Overview
ACEPOM 520 Laser Leveling Instrument for Wind Power Tower Tube
Product Details

The laser transmitter of the special laser leveling instrument for wind power tower tube adopts advanced laser source and has excellent laser beam quality.With automatic horizontal adjustment and a rotating and linear laser, flatness, straightness and other complex geometric measurements can be easily and accurately measured.Powered by a power supply or battery.The laser receiver USES a photosensitive coupling as a receiving sensor and measures a height range of 80mm that can be displayed directly on the screen.It can receive a rotating laser within 80 meters.It has not only a bluetooth device but also an infrared device.Connect it to the software via bluetooth for data transmission.The rotating laser can be automatically adjusted by infrared signal, and the real-time adjustment value can be displayed on the remote control by infrared signal.A transmitter or bluetooth device can be powered by a power supply or battery.


Use laser for flange measurement

Flange is an important connecting part, in order to ensure that the flange force uniform and avoid excessive stress, must be processed high precision flange. Especially in tower construction, due to the limitation of manufacturing method, it is difficult to make flange precise structure. When each flange is built, the flange will be stressed and deformed with assembly or welding. Therefore, accurate flange measurement can ensure long-term stable operation of the wind tower. In the past, attempts have been made to test the flatness of flanges by calibrating wood rods and guides. When a large diameter flange is encountered, this method cannot be used for measurement, so another method must be found. Only the fan area of the flange can be measured by means of a calibrating rod.   This measurement is called "short wave". Using a laser to measure a flange, a reference plane can first be created and then measured against this reference plane. Fix the T330 on the flange plane and activate the rotating laser. Using a laser receiver, the flatness can be measured at multiple points on the flange.


Use different methods to debug the laser plane:

According to the three arbitrary points on the flange to adjust the laser plane very accurately, the laser plane after debugging should be parallel to the flange plane determined by these three points.- this method takes a little time and the pros and cons of the measurement are related to the selection point.

Adjust the laser plane according to the Angle of the flange plane itself.- this method is fast, but requires computation.

Previously, measurements could only be calculated on a computer.Now, using advanced flange software measurement system can automatically get accurate measurement results in the field.



Measurement

The company is committed to making measurement technology as simple as possible and making measurement as fast and accurate as possible.To measure the flatness of the flange, simply fix the laser transmitter to the flange. The laser receiver can collect data from all measuring points on the flange (measuring points are not required in sequence). As shown in the figure: 104 measurement points on the flange can be measured in only 25 minutes. The measured data can be displayed as two - and three-dimensional graphs. After measurement, the measurement data can also be analyzed and evaluated.


Results and reports

A detailed report can be stored and exported in PDF format.The exported *.csv data file supports the use of Excel programs.So the measurements can be evaluated in any form.If a measurement point is measured incorrectly (e.g., the peak of the measurement curve), the point can still be re-measured and a new curve can be generated.


Parallelism measurement

Our product has the advantage of being able to extend the system for parallelism measurement.The parallelism of the two flange faces of the tower joint can be measured using only a laser transmitter and two laser receivers.Measurements are graphically displayed and compared and measurements can be stored and exported.


The base measurement

The laser measuring system can measure the flange base. In the past, cumbersome levels and measuring rods were used to measure the flange base. Today, the laser measuring system can be used to measure the flange base in just a few steps. First, the laser transmitter is horizontally adjusted and laser....calibrated (< 0.025mm /m) so that the rotating laser can scan all measurement points on the flange base. A laser receiver is used to collect data from all measurement points on the flange base. Measurements are displayed graphically and the results can be stored and exported.


Wheel measurement

Wheel hubs and wing flanges can also be measured in the same way.Components can be tested or repaired before the stress has affected the material.