Welcome Customer !

Membership

Shenzhen Wintop Optical Technology Co., Ltd,
Free Member ·1YRS
,
Other

Main Products: 光通信设备

Xwboo>Products

Shenzhen Wintop Optical Technology Co., Ltd,Free·1YRS

  • E-mail

    sales@wintoptec.com,shawn@wintoptec.com

  • Phone

    +8675586591151,+8675526641898

  • Address

    11F~12F, Senhainuo Kechuang Building,Shilong Community,Shiyan Street,Baoan District,Shenzhen

Contact Now

Broadband RF over Fiber TranceiverOptical transceiver

Model
Nature of the Manufacturer
Other
Product Category
Optical transceiver
Place of Origin
City, Province
Overview
Broadband RF over Fiber Tranceiver
Product Details

 

FEATURES

l  500 KHz to 6 GHz Bandwidth

l  tight Cast Metal housing

l  ?25? to +65? TOP Range

l  High SFDR

l  Flat Frequency Response

l  Auto Optical Power Control

l  1.3 and/or 1.5 μm Isolated DFB Lasers

 

APPLICATIONS

l  WiMAX / 4G LTE

l  2G/3G Repeater

l  MMDS

l  Remote Antenna Location

l  Outdoor DAS

l  GPS Distribution

l  Shipboard RF distribution

l  Satellite Ground station

 

DESCRIPTION

This module is a low cost high performance Broadband Optical Transceiver with very wide Dynamic Range designed for RF over Fiber applications. Designed for optical RF applications. This module offers high Spurious Free Dynamic Range (SFDR) with operational frequencies from 500 KHz to 6 GHz.

The standard optical connector is FC/APC for low back reflection applications and the RF interface is via a 50 Ohms SMA connector. The Receiver features a high performance InGaAs photodiode and the Transmitter is based upon a linear optically Isolated DFB Laser operating at either 1.3 or 1.5 μm over 9/125 μm Single Mode Fiber.Average Automatic Power Control (AAPC) is incorporated for optimal optical power stability over the full operating temperature range. 

Label:   RF optical module

Parameter

Symbol

Min

Typical

Max

Units

Notes

Power Supply Voltage

VCC

6

12

15

Volts

 

Power Supply Current

ICC

 

50

 

mA

 

Laser Optical Output Power

 

 

3

 

mW

 

Transmitter Operating Wavelength

 

 

 

nm

 

Receiver Operating Wavelength

 

 

1310/1550

 

nm

 

High Frequency Cutoff

HFC

 

6000

 

MHz

1

Low Frequency Cutoff

LFC

 

500

 

KHz

2

Frequency Response

500KHz– 1.0GHz

 

 

± 0.5

± 1

dB

 

10MHz– 2.5GHz

 

 

± 1.0

±1.5

50MHz– 3.0GHz

 

 

± 1.0

±1.5

400MHz– 4.2GHz

 

 

± 1.0

±1.5

500KHz–6.0GHz

 

 

± 1.5

± 2

Input/Output Impedance

Z

 

50

 

Ohms

 

Input/Output VSWR (500KHz–6.0GHzz)

 

 

1.7:1

2:1

dB

3,4

RF Link Gain

500KHz– 1.0GHz

 

 

-8

+15

10MHz– 2.5GHz

 

 

-8

+15

50MHz– 3.0GHz

 

 

-8

+15

400MHz– 4.2GHz

 

 

-8

+15

500KHz–6.0GHz

 

 

-8

+15

Input Noise Floor @ 1 GHz

EIN

 

-134

 

4

Input Third Order Intercept @ 1 GHz

IIP3

 

33

 

dBm

4,5

Gain change over Temp

 

 

± 2

 

dB

6

Isolation

 

60

80

 

dB

7

 

 

Parameter

Symbol

Min

Max

Units

Notes

Storage Temperature (Case)

TS

?40

+85

?

 

Operating Temperature (Case)

TO

?25

+65

?

 

DC Supply Voltage

VDP

+6

+15

Volts

 

Maximum RF input into Tx

 

 

+10

dBm

7

Maximum Optical Input into Rx

 

 

10

mW

 

 

1. Typical High frequency cutoff (HFC) is 6000 MHz. For higher HFC contact Factory.

2. Typical Low frequency cutoff (LFC) is 500KHz. For lower LFC contact Factory.

3. Measured and Specified with Optical loss budget of 0 dB, and 1 meter of SMF28 optical Fiber.

4.Max Gain is TX with one amplifier and RX with one amplifier

5. Equivalent to IMD 60dB@0 dBm Total Output Power (2 tone measurement).

6.?25 to +65 C. For other operating temperature ranges, or extended temp range contact the Factory.

7. Typical value across the whole band but Measured at 1GHz.

 

CONNECTOR CONFIGURATIONS

RF Connector = SMA Female

Optical Connector = FC/APC

Supply Connector = M2.5 Feed-thru Capacitor