Overview
VMS601 piezoelectric speed sensor is mainly used to measure the vibration speed of the shell. Mainly measure the vibration of the bearing housing, shell or structure (relative to the free surface). Different from the traditional magnetoelectric speed sensor, the sensor adopts the crystal form, is designed on the basis of piezoelectric accelerometer, and is embedded in the integrating circuit. Because it uses a crystal circuit and has no moving parts, it does not produce wear and degradation, has a long service life, and can be installed vertically, horizontally or at any angle.
The sensor uses a stainless steel shell, ICP type enhanced anti-interference design, suitable for rotating machinery and equipment in harsh industrial environments.
The wide frequency band design makes the frequency range of VMS601 piezoelectric speed sensor almost include the rotation speed of rotating machinery and its higher harmonics. High performance enables it to be applied to rotating machinery on industrial sites.
Technical Parameters
Electrical 1. Sensitivity: 4.0mV/mm/s (100mV/in/s) ±5% (25℃, 80Hz) 2. Speed range: 1270mm/sec (50in/sec) 3. Amplitude linearity: ± 1%FS 4. Response frequency: 2-5KHz (±3.0 dB) 5. Resonance frequency: 21KHz 6. Transverse sensitivity: 5% 7. Transmission distance: 305 meters long 8. DC bias voltage: 12V 9. Power supply voltage: 18- 30Vdc 10. Power supply constant current: 2-10mA 11. Electronic noise: 10μV rms (2Hz-20KHz) 12. Output impedance: <100Ω 13. Grounding: Shell insulation, internal shielding | Environment 1. Operating temperature: -40℃~+80℃ 2. Humidity: ≤99% non-condensing and non-soaking 3. Protection level: IP67 4. Impact limit: 5000g peak Physical 1. Weight: 100g 2. Housing material: Stainless steel 3. Output connector: MIL-C-5015, 2-pin (A, B end) 4. Pin A: Signal 5, Pin B: Common end 6. Mounting aperture: See Selection 7. Installation torque: 3N*m 8. Diameter: 1 inch (25.4mm) 9. Accessories: cable, installation conversion base, installation bolt |
Ordering information
main part 1: Probe
Order number | description |
VMS601 | The sensor output connector is a 2-pin MIL socket |
Note: The required options for the sensor include: [Main part 1: Probe, accessory 1: Connecting cable, accessory 2: mounting conversion base and accessory 3: mounting bolt].
Annex 1: Connecting cable
| Order number | Cable length A | Other B | description |
VMS600901-Ax-Bxx | Range: 1m≤A≤300m, in increments of 0.5m, default 3m. For example: A2.5=Cable length is 2.5 meters. | 00: No requirement | 2-pin MIL-C-5015 plug, with xm 2-core shielded twisted wire cable, diameter 4mm, <120℃. |
VMS600801-Ax-Bxx | 2-pin MIL-C-5015 plug, with xm 2-core shielded twisted armored cable, diameter 8mm, <150℃. |
VMS600701-Ax-Bxx | 2-pin MIL-C-5015 plug (right angle), with xm 2-core shielded twisted wire armored cable, diameter 8mm, <150°C. |
VMS600601-Ax-Bxx | 2-pin MIL-C-5015 sealed plug with xm 2-core shielded twisted wire cable, diameter 4mm, <120℃. |
Attachment 2: Installing the conversion base (standard configuration)
| Order number | description |
VMS600902 | This accessory is the standard configuration of the sensor, and can also be purchased separately as a spare part |
Attachment 3: Mounting bolts
| Order number | description |
VMS602103 | M6×1 |
VMS602203 | M8×1 |
VMS602303 | M10×1 |
VMS602403 | M10×1.5 (default) |
VMS602503 | 1/4-28UNF |
Note: Installation bolt length: 9mm
Chart size
VMS601 Piezoelectric Speed Sensor Dimensions