Membership
Help
Shijiazhuang Hanjiu Technology Co.,Ltd.
Shijiazhuang Hanjiu Technology Co.,Ltd.
101 Series Hydraulic Steering Units
101-1,2,3 Series Hydraulic Steering Control Units (SCU)
| Parameters | Type 101-*-***-* | ||||||||||
| Function Code | 1,2,3 | 1,3 | |||||||||
| Displacement(mL/r) | 50 | 63 | 80 | 100 | 125 | 160 | 200 | 250 | 280 | 315 | 400 |
| Rated flow (L/min) | 5 | 6 | 8 | 10 | 12.5 | 16 | 20 | 25 | 28 | 31.5 | 40 |
| Max. input pressure (MPa) | 17.5 | ||||||||||
| Max. cont. back pressure (MPa) | 2.5 | ||||||||||
| Weight (kg) | 5.70 | 5.76 | 5.84 | 5.91 | 6.05 | 6.25 | 6.45 | 6.68 | 6.86 | 7.06 | 7.45 |
| Dimension L (mm) | 130 | 132 | 134 | 137 | 140 | 145 | 150 | 156 | 161 | 166 | 176 |

The installation and use of full hydraulic steering note
1 installation precautions:
2 oil flow rate considerations:
3 other matters needing attention:
Troubleshooting of Metering Pump
| Matter | Causes | Troubleshooting |
| Oil leakage between back cover, stator and valves | rear cover stator bolt looseness (or uneven force), or O-rings damaged | Evenly tighten the bolt to the specified value, replace the seal (special) |
| Oil leakage at steering shaft | shaft seal ring excessive wear or damage | Replace the seal (dedicated) |
| feels light when turn the steering wheel slowly, feelsheavy when turn the steering wheel quickly | steering pump oil supply not enough | Check whether oil pump is working properly,(Including liquid level,pump efficiency, pipeline patency, etc.) |
| There is foam in the oil,irregular sound, the steeringwheel turns and the cylinder does not move | There is air in the steering system | Eliminating the air in the system, Check the suction pipe leaks or not, Orif the return nozzle is below the liquid level |
| Heavy steering continues to occur | Tank fluid is below the specified position | Add oil to prescribed height |
| Heavy oil viscosity | Use oil as required | |
| Feel heavy when turn fast and slow, stressless | Check valve between P,T failure | Check the ball. lf the steel ball is missing, then insert the steel ball; lfthe ball gets stuck dirty,it should be cleaned; In both cases,it isnecessary to check the effectiveness of the sealing tape recovery. |
| Turns light when the load is light,turns heavier whenincreas the load | relief valve pressure lower than steering requirement | Adjust relief valve pressure to specified value (no more than 16MPa) |
| Relief valve stucked by dirt, Or spring failure,Or seal is damaged | Clean relief valve (required to check the effectiveness of seal taperecovery), or replace the spring or seal | |
| steering wheel can't auto back to middle position | Spring broken or deformation | Replacement spring |
| Steering wheel rotate automatic swing to left or right | Rotor and linkage axes are not positioned correctly | Stop immediately! Align the teeth of the linkage shaft with rotor splines |
| No end point | Low pressure on relief valve | Appropriately increase relief valve pressure |
| Steering wheel rotates after turning to the end position | Low pressure on shock valves | Appropriately increase shock valves pressure |
| when machine is off, turn the wheel, cylinder not move | radial clearance or axial clearance is too large between radial and stator | Replace rotor and stator |
| Low viscosity of oil | Change oil | |
| Vehicle deviation Or the cylinder is slow when turningthe steering wheel | shock valves failure (ball caught by dirty, or spring failure, or seal damage) | Clean shock valves,replace spring or seal |
| pressure of Steering system is able to adjust | Spring broken | Change spring |
| not good seals at safety valve make the valve always open | replace parts | |
| Valve core stuck due to burr or oil stain | Remove, inspect, repair | |
| Poor spool operation | Check if the spool is stuck by dirty | |
| Spring bent or too soft | Change spring | |
| Oil is not clean, valve plug orifice is blocked | Replace the cleaning fluid and unblock the orifice |

| 1. Dust seal ring | 14. Spacer | 30. Complete relief valve |
| 2. Housing, spool and sleeve. Check valve and the seats for relief and shock valves are locktited. | 15. O-ring | 32. Complete shock valve |
| 3. Ball 8.5 mm [0.33 in] | 16. Distributor plate | 33. Ball 3/16 in |
| 4. Thread bushing | 17. Gearwheel set | 34. Rolled pin |
| 5. O-ring used with kin-ring (item 6) | 18. O-ring | 35. Ball |
| 6. Kin-ring | 19. End cover | 36. Bushing |
| 7. Bearing assembly | 20. Washer | 38. Spring |
| 10. Ring | 22. Special screw | 39. Kin ring |
| 11. Cross pin | 23. Screw | 40. O-ring |
| 12. Set of springs | 24. Name plate | |
| 13. Cardan shaft |