Welcome Customer !

Membership

XwbooInstrumentationOther Physical Property Testing InstrumentsHardness Tester3 Phase 2hp Motor
  • $item.Title
  • $item.Title

3 Phase 2hp Motor

Liyuan Motor Ltd

Model
Nature of the Manufacturer
Other
Product Category
Hardness Tester
Place of Origin
,

Liyuan Motor Ltd

Contact

Phone

+8613616092168

Fax

+86-593-6798813
MS series aluminum housing polyphase ac motor is made of superior materials and conform to the IEC standard.

Product Introduction

MS series aluminum housing 3 phase 2hp motor is made of superior materials and conform to the IEC standard. MS motor has good performance, low noise, safety, reliable operation and nice appearance. Motor can be maintained very conveniently. This series has advantages of little vibration, light weight and simple construction. These series three face motor can be used for general drive such as water pumps, water treatment, road machinery, petroleum, chemical, metallurgy, cement and paper industries.


Product Detail



Motor Type: 3 phase 2hp motor

Output Power: 0.06 kW - 18.5 kW

Frame Size: IEC 56 - 160

Number of Poles: 2, 4, 6, 8

Voltage: 220/380V, 380/660V, 230/400V, 400/690V (can be customized according to users)

Frequency: 50 & 60 Hz

Protection Level: IP54 / IP55

Energy Efficiency Rating: IE1 / IE2 / IE3

Insulation Class: B/F

Cooling Method: IC411

Working System: S1


Product Parameter (Specification)


image001


Production Features


image001

Know More Us


image006

Why Us


image008


Service and Packing


image009

FAQ



During the operation of the asynchronous motor, various faults will appear. So how should we deal with this kind of fault phenomenon and how to eliminate it? Today I will give you a brief introduction, I hope it can be useful to you help.


1. The motor does not start

1. The power supply is not connected: check the switch, melting wire, each pair of contacts and motor terminals.

2. Winding open circuit: heat the open circuit part to the temperature allowed by the insulation class, soften the paint, then stir up the broken wire, repair the broken wire with the same specification wire, wrap the insulating layer, and then paint and dry.

3. Winding grounding or short-circuit between phases and turns: The treatment method is the same as above, only insulate the grounded or short-circuited parts, and then paint and dry.

4. Winding wiring error: check the wiring diagram, and connect the ends according to the correct connection (including binding, insulation treatment, painting) after heating the end.

5. Melt burned out: find out the cause, eliminate the fault, and prepare a new melt according to the specifications of the motor.

6. Wrong operation of winding rotor motor starting: check the position of the collector ring and the short-circuit device of the starting rheostat. When starting, connect the rheostat in series with zero, and then connect the short-circuit device after starting.

7. The set value of overcurrent*** is too small: increase appropriately.

8. The old start switch oil cup is short of oil: add new oil to the oil level line.

9. Control equipment wiring error: the wiring is correct.

2. The melted wire is burnt after the motor is connected to the power supply

1. Single-phase start: check the power cord, motor lead wire, fuse, switch contact, find out the broken wire or false connection fault and repair it.

2. The stator and rotor windings are grounded or short-circuited: correct the error.

3. The motor load is too large or stuck: adjust the load to the rated value and eliminate the failure of the drag mechanism.

4. The cross-sectional area of the melt is too small: the melt cannot protect the motor from overload. Generally, the melt is selected according to the following formula, the rated current of the melt = locked-rotor current/2 ~ 3.

5. The starting resistance of the wound rotor motor is too small or short-circuited: eliminate the short-circuit fault or increase the starting resistance.

6. The connection wire between the power supply and the motor is short-circuited: check the short-circuit point and repair it.

3. The motor does not start after being energized and buzzes.

Improper selection of slot matching after changing pole rewinding: select reasonable winding form and winding pitch; appropriate small rotor diameter; recalculate.


Our HistoryLiyuan Motor Ltd, founded in 1989, is located in Fuan city, the electric motor town of China. Our company has floor area of 3500 square meters and is a professional manufacturer of small and medium size electric motors, equipped with advanced facilities, advanced production and perfect testing equipments. We are the excellent medium-small size motor manufacturer in China, aiming to provide the highest quality but lowest price to our clients.Our FactoryNow, We have a integrated team of high skilled technicians and professional salesmen with advanced product-development method and modernized management system. In order to manufacture high quality products, we make sure we take strict procedure controls, from “material select”, “machining”, “producing”. “assembling”, and “testing”, on each single part. All of our products are produced by national standard and reach the high level in China. Products is hot sale not only in domestic market also oversea regions such as South-East Asia, Middle Asia etc. Motors are quite welcomed and we received thousands good comments from customers.Our ProductThe main business of the company specially produces the cast-iron electric motor such as Y/Y2/IE2 general motor, YEJ break motor, YVF frequency controlled motor, YD multi-speed motor, YC/YCL/YL single phase motor, YTY pump motor, YLJ break motor etc and alluminum motor such as MS general motor, ML/MC single phase motor as well as brushed DC motor and brushed permanent magnet DC motor.
Similar Product Recommend