Welcome Customer !

Membership

XwbooSecurity & ProtectionDisplay DeviceDiode Display (LED)3Gbps Video SFP Optical ReceiverHD Video
  • $item.Title
  • $item.Title

3Gbps Video SFP Optical ReceiverHD Video

Shenzhen Ho-link Technology Co., Limited

Model
Nature of the Manufacturer
Other
Product Category
Diode Display (LED)
Place of Origin
,
DescriptionThe SFP Receiver are high performance, cost effective modules supporting dual data-rate of 3Gbps and 20km receive distance with SMF.The receiver consists of two sections: a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.The receivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to SFP MSA.

Features

Metal enclosure for Lower EMI

PIN photodetector

Compliant with SFP MSA and SFF-8472 with Single LC receptacle

Digital Diagnostic Monitoring:

Compatible with RoHS

Hot-pluggable

+3.3V single power supply

Operating case temperature:

Industrial : -40 to +85°C

Applications

HDMI/DVI/VGA/SDI Video Transfer

Description

The SFP Receiver are high performance, cost effective modules supporting dual data-rate of 3Gbps and 20km receive distance with SMF.

The receiver consists of two sections: a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.

The receivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to SFP MSA.

Absolute Maximum Ratings

Table 1 - Absolute Maximum Ratings

Parameter

Symbol

Min

Max

Unit

Supply Voltage

Vcc

-0.5

4.0

V

Storage Temperature

Ts

-40

+85

°C

Operating Humidity

-

5

95

%

Note: The absolute maximum ratings exceeding the limits listed may cause permanent damage to the device.

Recommended Operating Conditions

Table 2 - Recommended Operating Conditions

Parameter

Symbol

Min

Typical

Max

Unit

Operating Case Temperature

Standard

Tc

0

+70

°C

Extended

-40

+85

°C

Power Supply Voltage

Vcc

3.13

3.3

3.47

V

Power Supply Current

Icc

300

mA

Data Rate

3

Gbps

Optical and Electrical Characteristics

Table 3 - Optical and Electrical Characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Receiver

Centre Wavelength

λc

1260

1620

nm

Receiver Sensitivity

-22

-20

dBm

1

Receiver Overload

0

dBm

1

LOS De-Assert

LOSD

-20

dBm

LOS Assert

LOSA

-24

dBm

LOS Hysteresis

0.5

2

dB

Data Output Swing Differential

Vout

350

1800

mV

2

Maximum Back Reflection

-27

dB

LOS

High

2.0

Vcc

V

Low

0.8

V

Notes:

1. The sensitivity and overload specification refers to the input power levels for BER = 1E-12 against both PRBS and pathological patterns at SMPTE 259M, SMPTE 292M and SMPTE 424M rates.

2. Internally AC-coupled.

Timing and Electrical

Table 4 - Timing and Electrical

Parameter

Symbol

Min

Typical

Max

Unit

Bite Rate

BR

155

3000

Mbps

LOS Assert Time

t_loss_on

100

µs

LOS De-assert Time

t_loss_off

100

µs

Serial ID Clock Rate

f_serial_clock

400

KHz

MOD_DEF (0:2)-High

VH

2

Vcc

V

MOD_DEF (0:2)-Low

VL

0.8

V

Diagnostics

Table 5 – Diagnostics Specification

Parameter

Range

Unit

Accuracy

Calibration

Temperature

0 to +70

°C

±2°C

Internal / External

-20 to +85

Voltage

3.0 to 3.6

V

±3%

Internal / External

Bias Current

0 to 100

mA

±10%

Internal / External

RX Power

-23 to -3

dBm

±2dB

Internal / External

Pin Diagram

Pin Descriptions

Pin

Signal Name

Description

Notes

1

VEE_TX

Transmitter Ground

2

TX FAULT

Transmitter Fault Indication(Active High, Open drain)

Note 1

3

TX Disable

Transmitter Disable

Note 6

4

Mod-Def2

Transmitter Ground

5

Mod-Def1

I2C Clock

Note 2

6

Mod-Def0

I2C Data

Note 2

7

Rate Select

Not connected

8

RX_LOS

Loss of Signal(Active High, Open drain)

Note 3

9

VEE_RX

Receiver ground

10

VEE_RX

Receiver ground

11

VEE_RX

Receiver ground

12

RD-

Inv. Received Data Out

Note 4

13

RD+

Received Data Out

Note 4

14

VEE_RX

Receiver ground

15

VCC_RX

Receiver Power Supply

16

VCC_TX

Transmitter Power Supply

17

VEE_TX

Transmitter Ground

18

TD+

Transmit Data In

Note 5

19

TD-

Inv. Transmit Data In

Note 5

20

VEE_TX

Transmitter Ground


Notes:

Plug Seq.: Pin engagement sequence during hot plugging.

1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.

2) They should be pulled up with a 4.7k~10kΩ resistor on the host board. The pull-up voltage shall be VccT or VccR.

Mod-Def 0 is grounded by the module to indicate that the module is present

Mod-Def 1 is the clock line of two wire serial interface for serial ID

Mod-Def 2 is the data line of two wire serial interface for serial ID

3) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage between 2.0V and Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to less than 0.8V.

4) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES or Reclocker.

5) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.

6) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:

Low (0 to 0.8V): Transmitter on

(>0.8V, < 2.0V): Undefined

High (2.0 to 3.465V): Transmitter Disabled

Open: Transmitter Disabled

Host Board Power Supply Requirements

Typical Application Circuit


Mechanical Dimensions

Ho-Link Technology Co., Limited is the professional manufacturer of high definition video communication equipment in Shenzhen China.Our main products are 4K HDMI video converter,HDMI/DVI/VGA video converter,KVM converter,3G/HD-SDI video converter,mini type 4K HDMI/DVI video converter,mini type SDI video converter,4K/2K HDMI extender.we also supply the customized products with multi-function of video /audio /data /ethernet /contact closure /telephone.All products are exported to international markets including Europe,America,Middle east,Africa etc.Ho-Link is a technology-driven company committed to add values to our customers by providing the high definition video over fiber and network total solution through innovative research and development.Our products are backed by the strong R&D team,rigorous quality assurance system and plentiful production experience.Our customers are distributed in broadcasting and TV industry, video conferencing, education recording industry, medical and education industry, digital signage, road traffic and other industries with high requirements for video.
Similar Product Recommend