Membership
Help
Wuhan Goldhome Hipot Electrical Co., Ltd.
Wuhan Goldhome Hipot Electrical Co., Ltd.
Introduction |
Live Cable identifier plays an important role in cable construction and maintenance work. Currently on the market are not only for the instrument power cable identification, there are instruments for live cable recognition, but in the specific use, the actual cable site is often placed together with each other, using the instrument calipers clamping often cannot lead to recognition, and most recognition receiving part still use the pointer meter to indicate. The scene due to vibration failure. And the identification of the scene is often no use of 220V power, resulting in the use of inconvenient.
Based on this, using the current electronic technology to develop a soft coil liquid crystal display cable identification device, the main design change to use the dry battery power supply mode, can well solve the shortcomings of the above equipment, practical work has a very good help
Hot tag:Live Cable Identifier,multi-functional cable identifier,cable identification instrument.
Special note: This cable identification instrument has the functions of live cable identification and power-off cable identification at the same time. When power-off cable identification: it is strictly prohibited to connect to live cable. Live cable identification is only applicable to three core armored cable (with metal shield layer). During identification, the transmitting clamp and receiving clamp shall not be mixed, and the direction of input signal shall be consistent.
| Technology specification |
Transmitter specification
Function | Transmit complex pulse frequency current signal, display residual battery voltage, transmit dynamic indication of state |
Power | 11.1V large capacity Li-battery, Full charge continuous operation for about 8 hours |
Output ways | clamp input signal for live cable identification; direct output for power off cable identification |
Transmit frequency | 625Hz、1562Hz、2500Hz、10KHz(power on cable identification),press ↑ ↓ arrow to adjust frequency |
Pulse voltage | 500V(power off cable identification ) |
Pulse current | 5A max(depends on circuit resistance) |
Pulse frequency | 1times/sec |
Pulse width | 2ms |
Test wire length | 3m,Crocodile clip,red &black each 1pcs |
Transmitter clamp size | LWT=320mm×180mm×35mm |
Clamp Jaw dia. | φ125mm |
Clamp connect wire | 4m |
Grounding assist pin size | LWT=225mm×100mm×10mm |
Transmitter size | 320mm×275mm×145mm |
Display mode | Big LCD screen, online display currently battery voltage,with backlight |
LCD size | LW=128mm×75mm;display area124mm×67mm |
External tool bag size | LWH=400mm×245mm×335mm |
Work humiture | -10℃~40℃ |
Store | -20℃~50℃,≤95%RH, No condensation |
Backlight control | White backlight lamp |
Work humiture | -10℃~40℃ |
Weight | Transmitter 2.5kg;Transmitting clamp 1.12kg;total weight 4.44kg(with receiver) |
battery | When battery volt lower 9.65V, lower battery symbol display remind charge;when battery volt lower 9.5V,instrument power off automatically |
Charger | 12.6V DC |
Charge port | Circular audio jack,DC |
Withstand pressure | The transmitter adopts the integrated special toolbox design, and the box can bear the pressure of about 200kg |
Insulation | AC 3700V/rms(instrument shell) |
Electromagnetic characteristics | IEC61326(EMC) |
Comply certificate | IEC61010-1(CAT Ⅲ 300V、CAT IV 150V、pollution II) |
Receiver specification
Function | Identification of live cable and power-off cable; AC voltage, current and frequency test |
Power | 7.4V rechargeable Li-battery, USB charge port, full battery works 6hours |
Receiver frequency | 625Hz、1562Hz、2500Hz、10KHz |
Enlarge | 1dB、10dB、20dB press ← → key adjust |
Rated current | Approx 300mA max |
Display mode | 3.5inch LCD |
Signal calibration (sampling) | One of condition as the evidence to identify the target cable is current between 75%-135% |
| Calibrate 1-10pcs of cables, each calibration(sampling) data should be unchangeable after frequency, name and magnification firmed | |
Direction recognition | Have, one of condition as evidence to identify the target cable is direction consistent with transmitter&receiver |
Success identification | Display(√)symbol |
Non target cable | Display(×)symbol |
Receiver size | LWT=207mm×101mm×45mm |
Flexible current clamp | Approx L=630mm, wire diameter 6 mm or 12.5mm |
Current clamp jaw | φ200mm(customized) |
Connect wire | L:2m |
Volt test wire | L:1m (Red/Black each 1pcs) |
Measurement Range | Power-off cable identification:this instrument can detect the pulse signal with loop resistance of 0 Ω ~ 10K Ω;(ensure transmitter battery volt over 11v) in general, cable identification length can reach 0-20km,which depends on circuit resistance |
Live cable identification: the instrument can detect pulse signal with loop resistance of 0~200Ω(ensure transmitter battery volt over 11v) In general, cable identification length can reach 0-5km, which depends on circuit resistance | |
Range | AC volt: 0.00V~600V(50Hz/60Hz) |
| AC: 0.00A~5000A(50Hz/60Hz) | |
Frequency: | 45Hz~70Hz |
Accuracy | AC volt:±2%±3dgt |
| AC:±2%±3dgt | |
| AC frequency:±2%±3dgt | |
Signal | Colorful signal display |
Detecting speed | Approx 1times/sec |
Enlarge | At test interface,Press ← → signal enlarge,it is optimum for signal at range 10~100 |
Backlight | At startup interface, press ↑ ↓ key to adjust LCD backlight brightness |
Power off | Automatically power off after standby 30min for saving battery |
Battery volt | Battery volt lower 6.5V, low battery symbol display, remaind to charge battery |
Charger | 9V DC charger |
Charge port | USB charge port |
Work humiture | -10℃~40℃;80%Rh below |
Save humiture | -10℃~50℃,≤95%RH, no condensation |
Receiver weight | Current clamp 172g;receiver 370g(with battery) |
Withstand voltage | AC2000V/rms(between two points of the shell) |
Comply certificate | IEC61010-1 CAT Ⅲ 600V,IEC61010-031,IEC61326,pollution 2 |
| Structure |


1、FLEXIBLE COIL CONNECT POSITION
2、USB CHARGE PORT(8.4V CHARGER)
3、RECEIVER LABLE POSITION 4、RECEIVER LCD
5、RECEIVER POWER ON/OFF 6、ESC
7、ARROW & ENTER KEYS 8、VOLTAGE TEST JACK
9、FLEXIBLE COIL OUTPUT JACK
10、FLEXIBLE CURRENT CLAMP
11、FLEXIBLE COIL LOOSEN POSITION
12、FLEXIBLE COIL CONNECT WIRE
13、TRNASMITTER LABLE POSITION
14、POWER OFF CABLE CONNECT POSITION
15、TRANSMITTER LCD
16、POWER ON CABLE IDENTIFICATION TRANSMITTER CLAMP CONNECT PLUG POSITION
17、TRANSMITTER FUNCTION KEYS
18、TRANSMITTER DC CHARGE PORT(12.6V CHARGER)
19、EMISSION CURRENT CLAMP
20、TRANSMITTER CLAMP TRIGGER
21、EMISSION CLMAP CONNECT WIRE
22、POWER ON CABLE IDENTIFICATION TRANSMITTER CLAMP CONNECT PLUG POSITION