Membership
Help
XZH TEST
XZH TEST
XHSB505 is a new generation of cable identifier, it is an upgrade on the first generation of cable identification instrument, adding a frequency adjustment function, it can adjust the speed of signal transmission to meet the needs of the field.
Its working principle is to convert the 220VAC power input from the power grid into a special high-power special signal required for identification by electronic technology. This signal is added to the cable to be identified through the connecting line. According to the principle of electromagnetic induction, it must be generated and emitted along the cable. For the induction signal with consistent signal law, use a highly sensitive receiving clamp and a hand-held receiver to detect all cables on the test site. According to the instructions of the hand-held receiver, you can accurately find the cable to which the signal is added (ie, the cable to be identified).
![]() |
| |
The XHSB505 cable identification instrument consists of the identification instrument host, receiving clamp, hand-held receiver, etc. It can identify uncharged cables.

A. Current indication: Displays the instantaneous average value of the output current.
B. Work indicator: used to indicate that the instrument has an identification signal output.
C. Output terminals: red is positive, black is negative.
D. Output selection switch: "Ⅰ" is low gear; "Ⅱ" is high gear.
E. The frequency adjustment knob can adjust the transmission speed of the signal.
F. Start button: Press this button to start the instrument; the "work" light is on, and the instrument outputs a signal.
G. Stop button: Press this button to stop the recognition device from working.
H. Power switch: input AC220V, with a fuse socket to control the working power.
Receiver:
1. There is a potentiometer on the lower side of the handheld receiver, which can adjust the receiving sensitivity.
2. There is a BNC interface on the lower side of the handheld receiver, which is connected to the receiving clamp when in use.
Note: Sensitivity should be about 20-80% swinging left and right of the watch hand, don't be too sensitive.
ALL ENGLISH VERSION AVAILABLE
WELCOME YOU CONTACT US FOR MORE INFORMATION
Technical Parameters
Recognition method | Judging by the swing direction of the hands |
Jaw | Φ125mm |
Power | 1.5kVA (intermittent momentary) |
Weight | 11.00kg |
Dimensions | 700×300×220mm |
Signal sending frequency | Min: 0.4Hz, Max: 1Hz (range adjustable) |
Product Features
● Identification is accurate
●Large identification jaws fit all kinds of cables
●Very simple operation
●Clear and intuitive instructions
●The main and auxiliary parts are portable, beautiful and feel good
●Receiver sensitivity is adjustable.
●Signal frequency adjustment
The use of the instrument
1 Disconnect the two ends of the cable from the ground, and clamp the red clip of the output cable of the cable identifier to the core of the cable to be tested (the phase with good phase or high insulation), and clamp the black clip of the output cable of the tester. At the grounding point or grounding pile, the cable corresponding to the core wire is connected to the grounding point or grounding stub at the far end.
2 Turn on the recognizer power switch. Select output gear: "I" is low for short cables; "II" is high for long cables.
3 Confirm the status of the field cable and correct wiring, press the "Start" button.
4 Connect the recognizer receiver to the receiver clamp.
5 Note The direction of the receiving pliers arrow is the current inflow direction (positive direction), otherwise the hands will swing in the opposite direction.
6 Place the receiving clamp on the cable under test.
7 Adjust the receiver sensitivity to a suitable location
8 The handheld receiver can now see the wobble signal.

Packing List
Item | Name | Qty. |
1 | Cable Recognition System Host | 1 |
2 | Receiver | 1 |
3 | Receiving clamp (test clamp) | 1 |
4 | Output lines (1 red 1 black) | 2 |
5 | Power cord | 1 |
6 | Fuse Φ5×20 8A | 2 |
7 | Manual | 1 |
Onsite testing
|
|
We also manufacture LIVE CABLE IDENTIFIER, welcome you contact us for more information.
Remarks
◆This pointing device has passed the international standard certification ISO9001
◆The general delivery time of the equipment is 5-8 days. The specific negotiation at the time of ordering shall prevail.
◆The standard packaging is a wooden box for export to protect the safety of equipment transportation.
◆Usually shipped by international express, such as FEDEX, DHL, , ARAMEX, etc.
◆XZH Team is a young team. Our development philosophy is humanized management, intelligent cloud-based products, and internationalized operations. Our development mission is to make electrical equipment free from undetectable failures.


XZH TEST welcomes your inquiry
FAQ
Q: What’s your payment terms?
A: Payment≤USD2000, 99% paid in advance. Amount over USD2000, can be negotiated.
Q: Are you a manufacturer?
A: Yes, We are manufacturer.
Q: Why should you buy the cable identifier from us?
A: Professional R&D and technical support, accept OEM, ODM orders;
Provide overall laboratory solutions to your project.
Strict quality control and one year of warranty.
Short lead time and fast delivery.
Quick response to your any inquiries.