Welcome Customer !

Membership

XwbooInstrumentationFlow MeterFlowmeterClamp vortex flowmeter
  • $item.Title
  • $item.Title

Clamp vortex flowmeter

iangsu Zhongwei Measurement and Control Co., Ltd.

Model
Nature of the Manufacturer
Other
Product Category
Flowmeter
Place of Origin
,

iangsu Zhongwei Measurement and Control Co., Ltd.

Contact

Phone

18852328848

Fax

0517-86918679
Clamp vortex flowmeter
Description:

Products overview:
ZW - LUGB seriesOvercome the connection plate is needed in the general flow meter connector uniform bolt holes, using bolts, nut connecting plate fixed on the pipeline, the cost is high, the operation of trouble, the disadvantages of low efficiency, which adopts a transverse connection plate for right-angled trapezoid, inside right-angle trapezoidal bevel edge, use when using clamp plate fastening will be connected on the pipeline, use cost low, save time and effort.Measure the liquid in the pipe, automated testing instrument, is the ideal type, explosion-proof type and local display type, the clamp vortex street is applicable to many of the health industry.

Second, the working principle:
ZW - LUGB seriesClamp vortex flowmeterVertical in the measurement of tube inserted a pillars, the fluid through the pillars on both sides of the rules of the vortex is alternately, the spiral column is called the karman vortex street.The release of the karman vortex street frequency is related to the width of the fluid velocity and pillars, expressed by the type:
F = St · v/d type: - the release of the karman vortex street frequency f
St - coefficient (called, ha)
V - velocity
D - the width of the pillars
Karman vortex street release frequency f and is directly proportional to the velocity v, so by measuring the karman vortex street release frequency to calculate the instantaneous flow rate.
Stern lo ha is one of the important coefficient of vortex flowmeter.In its number of St 0.17 straight part of the material, the release of the vortex frequency is proportional to the velocity of flow, so check out the velocity v, frequency f can be obtained to calculate volume flow by v.
Vortex flow sensor be vortex frequency is applied to detect sensor by vortex alternately (probe) on in-situ stress in its internal piezoelectric element to check out.
Applications:
ZW - LUGB seriesClamp vortex flowmeterWidely used in food, chemical industry, metallurgy, machinery, paper, and the city pipe heating, water supply, gas and other industries of all kinds of low viscosity liquid, gas, steam, etc of single-phase fluid process measurement and energy saving management.
Four, the main features:
Simple 1, health industry, internals, clamp connection;
2, software configuration can be implemented all the requirements of different medium of different measurement configuration;
3, parameter setting can be set for measuring parameters of different fluid.Example: the gas deviation factor, instrument coefficient, rating, etc.;
4, since the diagnosis to set parameters, output signal, the signal sending and receiving, CPU fault diagnose, etc;
5, display a variety of diagnostic code, parameters such as flow, volume, flow percentage;
6, the output pulse, 4 ~ 20 ma.
Five, the technical parameters:
1, the accuracy of liquid: + / - 1.0%;
Gas, steam, plus or minus 1.0% FS (velocity < 35 m/s);
Plus or minus 1.5% FS (velocity of 35 m/s ~ 80 m/s);
2, 25,40,50,80,100,150,200,250,300 specifications;
3, medium temperature range: 25 ℃ ~ + 300 ℃;
4, the environment temperature range: 25 ℃ ~ 70 ℃;
5, 18 ~ 45 v DC power supply analog output;14 ~ 30 v DC pulse output;
6, work pressure 2.5 Mpa or less;
7, explosion-proof grade Exd Ⅱ CT1 ~ T6.
8, the degree of protection IP65.

Six, installation requirements:

1, the sensor should be installed in a horizontal, vertical, inclined (liquid flow from bottom to top) and its size in the same line.Sensors upstream and down 2, should be configured with a certain length of straight pipe, the straight pipe length should comply with the former 15 ~ 20 d, straight pipe after 5 ~ 1 od demands.

3, installation of liquid sensor near the pipe should be filled with liquid to be tested.

4, sensor installation should be avoided on the strong mechanical vibration of pipeline.

5, the inside diameter of straight pipe, as far as possible consistent with the sensor size, if not consistent, slightly larger than the sensor size should be adopted for the pipeline, the error to 3% or less, not more than 5 mm.

6, sensor installation should be avoided in the strong electromagnetic interference, the space is little, and maintenance is not convenient.

Seven, field requirements:
1, low maintenance - most of the vortex flowmeter are on the market with induction swirl hole or plug-in measurement, once the impurities embedded in the medium pressure hole or sensing element and the table body, the gap between the signal is weak or unstable.A good design should be not easy to plug part, thereby reducing amount of maintenance.
2, inductive components online replacement - some manufacturer of inductive components and vortex street close 2 for one, seemingly simple design to the actual use of inconvenience.Because once induction part failure, you need to medium to the pipe emptying replacement parts, after pressure relief effect production.Perfect design should be separated the two, so can replace the induction part alone, without emptying the media.
3, vortex flowmeter is vulnerable to vibration interference, well-designed vortex flowmeter can through hardware and digital signal processing to exclude interference, and the stability of the signal is obtained.
4, vortex flow meter before and after the installation of a hassle to very long straight section, some manufacturers can offer within the flowmeter reducing design, greatly reduces the user specifically MenWei vortex flowmeter with the demand of the straight pipe.
Need to pay attention to during the period of eight, debugging, using question:
1, flowmeter, on-site installation, maintenance, must abide by the "explosion-proof gas do not open" warnings, and in the open before turn off the power supply.
2, vortex flow meter used in outdoor, suggestion and side shields.
3, shall not be arbitrarily fixed part loosen the flowmeter.The protection of the pressure sensor.Users in the use of traffic time, should pay attention to the flow pressure overload value of pressure sensor is rated working pressure of 1.5 times (that is, the media zui high pressure of 1.5 times).Selection should be within the prescribed flow range, prevent overspeed operation, in order to obtain the ideal accuracy and ensure the normal service life.(due to pressure test, purging pipes or exhaust overdrive, and turbine operation in the reverse flow meter can cause damage)
4 when put into operation, the vortex street flowmeter, should slowly open valve, prevent damage of instantaneous flow and the turbine.Add lubricant should be according to the sign, the number of refueling depends on temperament clean degree, usually 2 ~ 3 times a year.
5, vortex street flowmeter runtime or alternate internal related parameters are not allowed to open the rear cover, otherwise will affect the normal operation of the meter.
Nine, install and use the items that should be paid attention to:
Vortex street no mechanical moving parts, small size, corrosion resistance, stable performance, can be directly display medium work pressure, temperature, flow rate and volume under standard state, wide range, the advantages of small measurement error, has been widely used in oil and gas well production measurement and gas sales.In field application over the years, we believe that the meter is suitable for relatively clean dry gas metering, gradually become small and medium-sized gas metering.To guarantee the accuracy of the flowmeter measurement, reduce the measuring error, please note:
1, the selection of reasonable
Don't make the actual z small flow meter QVmin below the selected through runoff flow range limit.
2, installation is correct
Upstream of the vortex flowmeter should have at least 10 d measuring straight pipe length.Straight pipe inner surface should be smooth, cannot have the steps, more smooth connecting flange weld, flange gasket can't into the pipe.Don't put the wrong installation direction of the flow meter.Tests showed that: all the unreasonable installation, will lead to the flowmeter measurement value is low.
3, away from the source of shocks, or install piers in upstream or downstream flow meter, in order to avoid the influence of the pipeline vibration.Avoid strong magnetic field disturbance to the flow meter chip.
4, temperament is relatively clean
Especially not a gas liquid two phase flow;Temperament is dirty, should clean instant flow meter.
5, and reduce the influence of flow pulsation
It can be installed in front of the flow meter buffer tank, or extended length of straight pipe upstream of the flow meter, computation.
6, timely flowmeter for metrological verification, to ensure accurate and reliable value.

Ten, standard of flow range profile: unit (m3/h)

traffic 

The liquid flow range

Gas flow range

Saturated steam flow range

CAL

Small flow

Heavy traffic

Small flow

Heavy traffic

Small flow

Heavy traffic

DN25

0.9

14

8.3

110

13

1500

DN40

2.5

35

26

300

25

4400

DN50

3.3

55

36

480

40

6800

DN80

8

150

90

1300

100

19000

DN100

14

240

140

2000

160

29000

DN150

38

450

290

4100

350

66000

DN200

70

850

620

7500

620

118000

DN250

130

1300

700

12500

970

185000

DN300

180

2000

920

16500

1400

267000

Eleven, selection of coding:

Code name

size

Flow range ㎡/h(In the wei and control)

ZW-LUGB-25

DN25

1 ~ 10(liquid)

25 ~ 60(gas)

Steam flow check specifications,DN300The above recommended plug-in vortex flowmeter

ZW-LUGB-32

DN32

1.5 ~ 18(liquid)

15-150(gas)

ZW-LUGB-40

DN40

2.2 ~ 27(liquid)

22.6 ~ 150(gas)

ZW-LUGB-50

DN50

4 ~ 55(liquid)

35 ~ 350(gas)

ZW-LUGB-80

DN80

9 ~ 135(liquid)

90 ~ 900(gas)

ZW-LUGB-100

DN100

14 ~ 200(liquid)

140 ~ 1400(gas)

ZW-LUGB-150

DN150

32 ~ 480(liquid)

300 ~ 3000(gas)

ZW-LUGB-200

DN200

56-800(liquid)

550 ~ 5500(gas)

Code name

function1

N

No temperature pressure compensation

Y

With temperature compensation

Code name

Output type

F1

4-20mAOutput (two-wire system)

F2

4-20mAOutput (three-wire system)

F3

RS485Communication interface

Code name

Measured medium

J1

liquid

J2

gas

J3

steam

Code name

The connection method

L1

Flange mounted

L2

Flange connection type

L3

Thread link type

L4

Clamp type health

Code name

function2

E1

1.0level

E2

1.5level

T1

The normal temperature

T2

The high temperature

T3

steam

P1

1.6MPa

P2

2.5MPa

P3

4.0MPa

W1

internal3.6VThe power supply

W2

DC24VThe power supply

N1

Stainless steel

N2

Carbon steel

N3

Anti-corrosion type

Twelve,Order to choose selection guidelines:

Name and model number of 1, 1), (2) the diameter, flow range, (3) whether or not to bring the attached so that we can correct selection for you, (4) using pressure, (5) the use of medium temperature.

2, if has been selected by design units in the way of vortex street flowmeter types, please press type vortex flowmeter directly order from our sales department.

3, when using occasions is very important, or the environment is complex, please try to provide the design drawings and detailed parameters, by wei experts in our audit checks for you.

After-sales service commitment:

1, from the date of signing of the contract, I in the way provided for products of the company offers free maintenance and maintenance service, commitment to lifelong maintenance service;

2, jiangsu wei measurement and control instrument co., LTD. Sales manager will be in regular contact with customers, understand the usage of products, and solve the problems of the customers to use in the process of produce, free of charge to provide technical support;

3 the man-made damage is found, the warranty period, our company is responsible for the maintenance, and the resulting maintenance fee;

4, product quality problems or are not satisfied with product, the user can choose unconditional return, wei tt&c don't charge any fees, appear quality problem, bear the freight back and forth.

iangsu Zhongwei Measurement and Control Co., Ltd. is located in Huaian City, the hometown of Premier Zhou, a great man of one generation. It has beautiful scenery, pleasant climate and abundant products. Main Products: Main Products: Intelligent Vortex Street Flowmeter, Intelligent Electromagnetic Flowmeter, Liquid Turbine Flowmeter, Elliptical Gear Flowmeter, Universal Electronic Flowmeter, Magnetoelectricity Flowmeter, Swirl Flowmeter, Metal Tube Float Meter, Wilba Flowmeter, Delta Bar Flowmeter, Orifice Flowmeter, Balanced Flowmeter, Air Measuring Device, Heat Meter, Ultrasound Flow Meter Meters, magneto-sensitive electronic double-color liquid level gauge, boiler drum level gauge, mica double-color water level gauge, radar level gauge, ultrasonic level gauge, magnetic turning plate level gauge, level (level) switch, pressure differential pressure transmitter, thermometer, thermoresistor, thermocouple, display, recorder, calibration equipment, wire and cable, control valve, etc. Professional R&D and sales of industrial automation products, providing integrated technical services of industrial automation system, is a comprehensive industrial automation product R&D and technology enterprise in China, which is built and developed at the beginning of the industry scale.The company's quality assurance system is complete. The company has a number of high-tech professionals engaged in the design, development, installation and commissioning of automation control research for a long time, which provides a satisfactory set of systems for various industries. It gathers strong professional team, accumulates abundant technology and management experience, covers the national marketing network and branches, and can provide users with technical services quickly and conveniently. In the era of Internet commerce, the company has set up the E-Commerce Department, relying on professional network technology and e-commerce trade means, to implement the integration of traditional economy and resources as well as rapid market expansion in a wide range. Since its establishment, the company has established a long-term and stable business and trade partnership with manufacturers in various regions by virtue of its good reputation and high-quality service.In line with the business philosophy of "satisfying customer's needs and creating value for customers", we have provided a large number of complete sets of services for users in oil field, power, chemical industry, metallurgy, paper-making, cement and other industries for many years to improve more seamless services for our customers. You can purchase online, learn business knowledge independently, serve your customers better, and create more value for you for five consecutive years. Our products are sold overseas, and we have distribution agents in many regions to further increase domestic marketing and expand the brand of Zhongwei. From 2011, we will recruit agents and distribute in the whole country. We can also provide OEM services for you. The quality service is consistent with that of Jiangsu Zhongwei. We promise you the best quality, the best service and the best price!The company adheres to the development policy of "science and technology, innovation, quality and service", continues to adhere to the purpose of "building an industrial aircraft carrier and contributing to the national economy". In the future development, it will continue to devote itself to brand building and constantly cultivate new economic growth points. Jiangsu Zhongwei will actively participate in market competition with high-quality products, preferential prices and excellent services, and wholeheartedly participate in friends from all walks of life. Friends, old and new customers cooperate in good faith, work hand in hand with Zhongwei measurement and control, create a better tomorrow.
Similar Product Recommend