Membership
Help
CEEG Nanjing Transmission & Distribution Equipment Co., Ltd.
CEEG Nanjing Transmission & Distribution Equipment Co., Ltd.
Dry Type Mining Explosion-Roof Transformer
Basic Info.
| Model NO | KBSG |
| Usage | Distribution Transformer |
| Brand | CEEG |
| Rated Capacity | 100-4000kVA |
| Primary Voltage | 6/10kv |
| Secondary Voltage | 0.69/0.4/1.2/3.45kv |
| Frequency | 50/60Hz |
| Impedance | 4%/4.5%/5%/5.5%/6% |
| Connection Symbol | Dyn11/Dy11/Yy0(D11)/Yyn0 |
| Tapping Range | ±5% |
| Transport Package | According to Client′s Requirements |
Production Introduction
This series of mine flameproof dry-type transformer is a non encapsulated dry-type transformer with H-class insulation grade and high-quality Nomex insulation materialmanufacturing technology.
The high and low voltage coils are made of Nomex insulating material, impregnated with H-class solvent-free paint (VPI - vacuum pressure impregnated) under vacuum pressure and cured at high temperature.
The high voltage coil adopts a layer type structure, andthe outermost two layers of wires are wound vertically, so as to improve the radial mechanical strength of the elliptical coil.
The core is made of high-quality and high permeability cold-rolledsilicon steel sheet, the core column is elliptical section, full inclined seam, and the upper and lower yokes are fastened by pulling plates and belts. The structure is advanced, compact and reliable. The explosion-proof shelladopts corrugated cylinder structure, which has good heat dissipation performance, high mechanical strength and compact structure.
This product has the characteristics of energy saving, strongoverload capacity, small amount of partial discharge, high reliability, long operation life, moisture-proof, mildew proof, salt spray proof, flame retardant, pollution-free, small volume, light weight, etc., and the top ofthe shell is not ponding and not easy to accumulate dust, so it is suitable for use in mines.
Production Features
Safety:
Sealed﹑moisture-proof﹑anticorrosion﹑explosion-proof design for tank
Air-insulation dry type transformers inside
Reliability:
Innovations in technology, professional design:
Tank: Adopting German rippled tube-shaped cover, high mechanicalstrength, excellent cooling performance
Insulation system: H class insulation system with AmericanDuPont® NOMEX@ paper as main insulation
Non-enveloped oval shaped coil, VPI (vacuum pressure impregnation)method, excellent electrical performance and strong over-load ability
The core is made of high flux material, with oval section.Compact structure, solid and reliable
Easy usage:
Compact design, small size and light weight
Pulling in the bottom of the transformer easy for transportation
Eight points fixed, easy for vertical move into the mine
Unique wire connecting room, easy for operation
l. Rated capacity: 100, 200, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000、3150、4000 kVA
2. Rated voltage: Primary voltage 6000, 10000 V
Secondary Voltage: 400 (380)693 (660) 1200 (1140)3450 (3300) V
3. Rated frequency: 50 Hz
4. Phase number: 3 phases
5. Cooling method: Natural air Cooling (ANAN)
6. Heat-resisting grade of insulating materials: H
Service Conditions
A. Altitude shall not be over 1500m
B. Highest temperature no more than 40ºC
C. Relative humidity shall not exceed 95% (+25ºC)
D. No severe shaking and vibration, and the gradient to vertical should not exceed 15°
E. It can be used in the places where exists methane mixed gases or coal & dust that make cause explosions; but no gas or vapor that may erode or destroy metals
F. Environment without water dripping or environment with water-proof facilities
G. Voltage wave form is similar to sine wave and three-phase power voltage is near symmetry.