Welcome Customer !

Membership

XwbooCasting MachineryCasting EquipmentSteel Casting EquipmentLost Foam Casting line
  • $item.Title
  • $item.Title

Lost Foam Casting line

Qingdao Antai Heavy Industry Machinery Co.,Ltd.

Model
Nature of the Manufacturer
Manufacturer
Product Category
Steel Casting Equipment
Place of Origin
ShanDong, QingDao
Lost Foam Casting line


Lost foam casting Process:


First, a pattern is made from polystyrene foam, which can be done by many different ways. For small volume runs the pattern can be hand cut or machined from a solid block of foam; if the geometry is simple enough it can even be cut using a hot-wire foam cutter. If the volume is large, then the pattern can be mass-produced by a process similar to injection molding. Pre-expanded beads of polystyrene are injected into a preheated aluminum mold at low pressure. Steam is then applied to the polystyrene which causes it to expand more to fill the die. The final pattern is approximately 97.5% air and 2.5% polystyrene. Pre-made pouring basins, runners, and risers can be hot glued to the pattern to finish it.

Next, the foam cluster is coated with ceramic investment, also known as the refractory coating, via dipping, brushing, spraying or flow coating. This coating creates a barrier between the smooth foam surface and the coarse sand surface. Secondly it controls permeability, which allows the gas created by the vaporized foam pattern to escape through the coating and into the sand. Controlling permeability is a crucial step to avoid sand erosion. Finally, it forms a barrier so that molten metal does not penetrate or cause sand erosion during pouring. After the coating dries, the cluster is placed into a flask and backed up with un-bonded sand. The sand is then compacted using a vibration table. Once compacted, the mold is ready to be poured. Automatic pouring is commonly used in LFC, as the pouring process is significantly more critical than in conventional foundry practice.

There is no bake-out phase, as for lost-wax. The melt is poured directly into the foam-filled mold, burning out the foam as it pours. As the foam is of low density, the waste gas produced by this is relatively small and can escape through mold permeability, as for the usual outgassing control.

Lost foam casting process Advantages:

This casting process is advantageous for very complex castings that would regularly require cores. It is also dimensionally accurate, maintains an excellent surface finish, requires no draft, and has no parting lines so no flash is formed. The un-bonded sand of lost foam casting can be much simpler to maintain than green sand and resin bonded sand systems. Lost foam is generally more economical than investment casting because it involves fewer steps. Risers are not usually required due to the nature of the process; because the molten metal vaporizes the foam the first metal into the mold cools more quickly than the rest, which results in natural directional solidification.[3][5] Foam is easy to manipulate, carve and glue, due to its unique properties. The flexibility of LFC often allows for consolidating the parts into one integral component; other forming processes would require the production of one or more parts to be assembled.

The two main disadvantages are that pattern costs can be high for low volume applications and the patterns are easily damaged or distorted due to their low strength.If a die is used to create the patterns there is a large initial cost.

This process eliminates the need for sand binders and cores. The sand is unbonded and a foam pattern is used to form the shape of the casting. The foam pattern is “invested” into the sand at the Fill & Compact process station allowing the sand into all voids and supporting the foam patterns external form. The sand is introduced into the flask containing the casting cluster and compacted to ensure all voids and shapes are supported.

The flask is transported to the pouring operation. The foam is evaporated as the metal is poured allowing the metal to take the shape of the casting cluster. Separation of sand and metal is accomplished at a Flask Dump Station. With no binders in the sand this process is performed with ease. Systems can be designed to accommodate quenching operations if required. The cluster proceeds to the casting finishing area for sprue, gate and riser removal. The sand is reprocessed by classification and cooling to be re-used. Thermal reclamation of the sand will extend the useful life. Lost Foam offers an environmentally friendly process with the added advantage of more accurate casting.

Foam patterns are created from polystyrene beads. The beads start as hard granules, very similar in size and shape to sand granules. The beads are expanded, allowed to stabilize and then molded into the desired shape. More complex shapes require multiple patterns to be glued together. The assemblies are then attached to a generic, central foam piece called a tree. Multiple patterns can be produced on a single tree. After assembly, the entire tree is dipped into a refractory coating to strengthen the tree. The assembled, strengthened tree is attached to a pouring funnel (called a sprue) and placed into the flask.




  Founded in 2003, Qingdao Antai Heavy Industry Machinery formally changed to its current name in 2011, located at No. 867 Century Avenue, Huangdao District, Qingdao City, Shandong Province,China.1.Registered Capital: 18 million RMB;2.Factory covering area 20,000m2;3.138 employees;4.Antai Group and China University of Petroleum jointly established the Antai Haibo Technology R&D Center, which focuses on the research and development of new practical equipment for shot blasting.The technical department also has many senior engineers and professional 3D designers with more than ten years of design experience.5.Qingdao Antai Heavy Industry Machinery Co., Ltd. has Qingdao Antai heavy industry international trade Co., Ltd., which is responsible for exporting all kinds of industrial auxiliary products and equipment.The chief engineer(30+ years of design experience) of the company is a member of the China Foundry Machinery Standards Committee. The company participates in the formulation of a number of national and industry standards. It has more than 30 patents for various inventions and utility models. Through cooperation with China University of Petroleum (East China), Shandong University of Science and Technology and other universities, the company undertakes some major scientific and technological research and development tasks in the new area. Through continuous improvement of products, it has successively served large enterprises such as China Aerospace, China Nuclear Power, China Railway Urban Construction, China Railway, China Shipbuilding, Anshan Iron and Steel, and has been widely praised.ANTAI GROUP is a research, design, manufacture, installation and consulting factory company for the surface finishing, environmental protection and foundry solution.Company has extensive experience and brings the technical and professional workers together, mainly produces:Shot blasting equipmentSand blasting equipmentPainting equipment lineFoundry equipmentEnvironmental protection systemIndustrial robotic equipment.We design and production various non-standard machinery according to user needs, providing integrated technology solutions for specific customers."Quality create brand, Brand promote development, Development without limit" is our business purposes, to establish a sound quality management system and network information feedback system, a separate filing for each client to achieve pre-contract order, sale produced delivery, sale and installation of all sectors and efficient docking, the maximum for customers with caring and thoughtful, efficient and flexible full service. With high-quality products, attentive service, our products have been sold in more than 75 countries, Like Russia, Belarus,Kazakhstan, Ukraine, Hungary, Macedonia, Greece, Pakistan, Saudi Arabia, Oman, United Arab Emirates, Malaysia, Philippines, Indonesia, Singapore, Vietnam, Morocco,Thailand, Myanmar, United States, Mexico, Chile, Bolivia and Argentina etc.and a large number of domestic manufacturers to establish mutual trust and good relations of cooperation and win-win.Company strength and certificate:1.All design adopt 3D Design. The first company in Qingdao adopts all 3D design.2.All adopt general parts, easy to buy and replace.3.International certification: CE,ISO14001,ISO9001,TUV,BV.4.Domestic certificate:AAA corporate certificate(The first AAA enterprise in Qingdao);5.Issued by Qingdao Municipality:Certificate of High and New Technology Enprise;6.Issued by Shandong Municipality: Certificate of Confidence and Trustworthiness;(There has never been a legal dispute)We always adhere to "honesty is the best selling, personalized service is the final product. Customer satisfaction is the greatest impetus to the development of enterprises." Aim to establish a perfect quality management system and network information feedback system for filing separately for each customer, to provide customers with maximum caring and thoughtful, efficient and flexible full service.
You May Like
Similar Product Recommend