Welcome Customer !

Membership

XwbooWarehouse LogisticsCard ReaderUHF RFID ReaderOxygen Sensor
  • $item.Title
  • $item.Title

Oxygen Sensor

ZHENGZHOU, HENAN, CHINA (MAINLAND)

Model
Nature of the Manufacturer
Other
Product Category
UHF RFID Reader
Place of Origin
,

ZHENGZHOU, HENAN, CHINA (MAINLAND)

Contact

Phone

+8615639095718

Fax

+8637186533226
The oxygen sensor is a current source, and the current depends on the oxygen reaction rate (Faradays law). The voltage can be measured by connecting a known resistance. If the oxygen flow through the sensor is completely limited diffusion, this electrical signal can reflect the oxygen concentration.
Introduction

The life of the sensor is 2 years, and it can directly measure oxygen in the concentration range of 0-25%. The pins on the bottom of the sensor can be directly connected to a PCB board. This sensor is suitable for portable or fixed safety devices.

Output model

The operation of the oxygen sensor is simple, which is achieved by connecting a low resistance resistor to generate a voltage signal. The maximum voltage signal must not exceed 100mV.

In most cases, a 100Ω resistor is sufficient. In general, the higher the resistance value, the longer the response time of the sensor. It is important to choose a suitable range of resistors to eliminate changes and long-term drift between the sensors due to differences in output current and temperature.

Linear relationship

The signal generated in this oxygen series is slightly non-linear (refer to Figure 2), following the following formula:

Note: If the sensor is calibrated in dry air, the value is 20.9% (S = 20.9, C = 0.209). This results in a K value of 89.14.

In the figure, the percentage concentration of oxygen in both curves is in the range of 0-20.9%, which reflects the relationship between the signal output during the calibration in the air and the oxygen concentration. The maximum deviation occurs when the oxygen concentration is 10%, and the output value is 0.5% lower than the standard value. In most cases, this deviation is negligible, but if necessary, digital technology can be used to compensate.

Carrier gas impact
In most cases, the oxygen sensor can be calibrated in ambient air, but if it is a high-concentration gas other than air, the carrier gas (that is, very little mixed oxygen) will have a greater impact on the output signal.

The output signal depends on the oxygen diffusion rate, which depends on the molecular weight of the carrier gas (Graham's law). The dry air contains 20.95% oxygen, and the remaining nitrogen with a molecular weight of 28, so when the carrier gas used is a gas with a molecular weight greater than that of nitrogen, the output signal will be greatly affected.


TAG:  Oxygen Sensor Bosean gas  gas sensor oem
Specifications
Operation notes
Please follow the instructions below to ensure proper use.

The sensor must not be stored for more than six months, and must be stored in a sealed container placed in clean air at 0-20 ° C.

The sensor cannot be stored in an environment containing liquid vapor. All sensors can not be used in the environment containing organic vapor, otherwise it will destroy its performance.

It must not be stressed during installation and fixation.

Because the sensor contains a small amount of lead, the discarded sensor must be properly disposed to protect the environment.


TAG:  Oxygen Sensor Bosean gas  gas sensor oem
Henan Bosean Electronic CO.,Ltd.was founded in 2013, with its headquarter located in Zhengzhou New High-tech zone. specialized in the development、sales of gas detection and measurement instruments, and providing technical services for customers. With its strong technical force and economic strength, Bosean constantly develops new innovative products of the international level. And Bosean is one of the most influential service providers in China, having branch offices and services centers all over the country, and serviced for more than 1000 enterprises.Bosean has a wide range of products, such as, portable gas detectors, 4-in-1 gas detectors, toxic gas detectors, CO gas detectors, combustible gas detectors, gas alarm, gas detector for mine use, transformers, detector with built-in pumps, etc. At the same time, Bosean engaged in the development and production of laser rangefinders, altimeters, angle meters. its products are widely used in machinery, mining, metallurgy, construction, chemical, casting, electricity and other industries.Since its inception, Bosean, upholding its integrity、pioneering and innovative enterprising spirit, has gained one after another remarkable achievements and won a good reputation. Bosean will keep focusing on its customer-oriented and application-oriented strategy, and continue to make contributions to the gas detecting industry.
Similar Product Recommend