Welcome Customer !

Membership

XwbooInstrumentationTesting MachineOther Testing MachinesSF6 Gas Recovery Unit
  • $item.Title
  • $item.Title

SF6 Gas Recovery Unit

Wuhan Goldhome Hipot Electrical Co., Ltd.

Model
Nature of the Manufacturer
Manufacturer
Product Category
Other Testing Machines
Place of Origin
HuBei, WuHan
1.RecoveryRecovery of initial pressure≤0.8MPaRecovery of final pressure≤50KParecovery time :The recovery time is less than 2.5 hours for 1 m3SF6 gas volume of 0.8 MPa of initial pressure to 50 KPa, of final pressure.2.StorageStorage container volume 0.015m3Nominal liquid storage 20kgMaximum storage pressure 3.8 MPa
I. Introduction


SF6 gas, as an insulating gas, has non-toxic, non-flammable, and good insulation characteristics. its insulation strength is much higher than that of traditional insulating gas, and it has good arc extinguishing, therefore,it is widely used in SF6 electrical appliances. Because the SF6 gas is expensive, and under the action of arc, electric spark and corona discharge, it will decompose and produce toxic components. Therefore SF6 the application of electrical equipment needs to recover the SF6 gas. This device is a special equipment for the recovery and filling of SF6 gas in the manufacture and maintenance of electrical equipment.


II. Technical parameter


1. Recovery

Recovery of initial pressure≤0.8MPa

Recovery of final pressure≤50KPa

recovery time :The recovery time is less than 2.5 hours for 1 m3SF6 gas volume of 0.8 MPa of initial pressure to 50 KPa, of final pressure.

2.gas charging

The volume of 1 m3SF6 gas with initial pressure of 133 Pa is filled to 0.8 MPa, and the aeration time is less than 0.8 hours.

3.Vacuumizing

Equipment limit vacuum less than or equal to 10 Pa.

Vacuuming to 133 m3SF6 of gas volume at an initial pressure of 0.1 MPa takes less than 1.0 hours.

4. Storage

Storage container volume 0.015m3

Nominal liquid storage 20kg

Maximum storage pressure 3.8 MPa

5. purify

The water content of SF6 gas below 1000 PPM( volume ratio) is less than 60 PPM( weight ratio) and the oil content is less than 10(weight ratio)

6.Annual leakage rate≤1% nominal storage

7. noise≤75 dB (A) Sound pressure level

8.operating ambient temperature -10°—40℃

9.power≤5KW

10.Power source:AC three-phase five-wire system 50HZ 380V±10%

11.Net Weight: 400 kg

12.Measuring size (Length×wide×Height):1360×800×1300

Model: HMLY-7Y-15-50

Item

Indicator Name and Unit

HMLY-7Y-15-50


1

Power supply AC

V

380

2

Maximum rated gas storage pressure(20℃)

MPa

≥4

3

ultimate vacuum

Pa

≤10

4

Vacuum Maintenance

Pa

Pressure Pa 133 maintained 24 h, vacuum value increased <400

5

Compressor pumping rate

m3/h

Compressor of 7 m³/h Merlot, France

6

Vacuum pump pumping rate

m3/h

bipolar pump 54 m3/h=15 L/S

7

Recycle device for initial inlet pressure(20℃)

MPa

0~0.8

8

Electrical equipment recovery final pressure(20℃)

MPa

≤50 Kpa

9

Gas oil control after recovery

μg/g

oil<10

10

Annual air leakage rate

%

<1

11

Continuous failure-free running time of the device

h

≥1000

12

Cumulative no-fault operating time

h

≥5000

13

noise level

dB(A)

complete machine ≤75

14

Actual liquid storage capacity

KG

50

15

Refrigerated liquefied compressor


compressor

16

Refrigerated tanks

L

50

17

Gas moisture recovered(PPM/V)

PPM/V

60

18

Gas oil recovery (PPM/V)

PPM/V

60

19

Dry filtration


Vacuum heating and regeneration

20

Inflatable initial pressure(pa)

pa

≤133

21

Inflatable final pressure(mpa)

mpa

0.8

22

Inflating rate(m³/h)

m³/h

≥5

23

gasification mode


Electric heating automatic temperature control

24

dimension

L*W*H

1360×800×1300(mm)

25

vacuometer


Yunjie brand


details


III.Working principles and structural features


The HMLH-7Y type SF6 gas recovery and discharge device has the comprehensive functions of recovery, charge and discharge, purification, vacuum pumping, storage, bottle filling and so on. The system is relatively complete, see Appendix I system diagram. The series or switching of each function is accomplished mainly by operating the electronic control box and ball valve on one side of the panel.

The basic working principle of the recovery device is the freezing liquefaction method. When recovering, the SF6 gas in the electrical equipment is inhaled into the compressor by using the suction and compressibility of the compressor and compressed to a higher pressure. The high temperature SF6 gas is cooled to the condensation temperature for liquefaction and storage by using the low evaporation temperature characteristics of R22 refrigerant. Continuous suction to SF6 compressor series operation until the final recovery pressure.

When filling and discharging, the vacuum pump of the device is first used to vacuum the SF6 electrical equipment (or cylinder) and the connecting pipe. Then directly use the pressure difference or the suction of the compressor and cause a certain pressure difference to fill the SF6 in the storage container into the SF6 electrical equipment until the required working pressure is reached. The liquefied SF6 is poured directly into the cylinder, taking into account the characteristics of the R22 refrigerant as described earlier when filling the cylinder.

The purification function is accomplished simultaneously when the above recovery and charging functions are completed。

3 oil separators are installed in the system, one at the outlet of the vacuum pump and two at the outlet of the compressor, respectively, to effectively remove the oil from the SF6 gas。

A drying filter is provided in the system loop to ensure the purity of the SF6 entering the storage container and to effectively remove moisture. The filter is equipped with a heating regeneration device, which can be heated and regenerated under vacuum, and the molecular sieve can be used repeatedly。

A reliable safety protection device is provided in the system, and the high pressure controller is installed at the exhaust port of the SF6 compressor. Once the exhaust pressure exceeds the limit value, it will automatically stop the compressor and restart the compressor after the pressure drops; The safety valve is installed on the storage vessel.

There are also seven monitoring instruments and control instruments in the system, one of which is installed in the recovery air inlet of the device and the DN8 valve is installed in front of the vacuum gauge and can be opened when observation is required; five pressure gauges are installed on the recovery air inlet, the SF6 compressor exhaust port, the refrigeration compressor suction exhaust port and the storage container respectively; and a thermometer is installed on the refrigeration system to SF6 the liquid temperature using the temperature package induction.

The inlet of the vacuum pump in the system is equipped with an electromagnetic vacuum belt inflatable valve and is connected to the vacuum pump on the same power supply. When the pump stops working, the valve can automatically close the vacuum system and fill the atmosphere into the pump chamber through the inlet of the pump, thus avoiding the reverse flow of pump oil to pollute the vacuum system.

The refrigeration system in the system is set by the high and low pressure controller. Once beyond the limit, the work of the compressor will be cut off by itself. When the pressure rises or the high pressure is disconnected, the compressor will be restarted after the pressure falls back.

Overall structure, the device is manual, can be used under normal indoor and outdoor conditions. A complex system consists of vacuum pumps, SF6 compressors, refrigeration systems, storage containers, pipes, valves, instruments and other accessories.

The electronic control box, operating valve and monitoring instrument are all concentrated on one side panel and have flow indication, so it is convenient and clear to use.


IV.Company Profile


Wuhan Goldhome Electrical Equipment Co., Ltd .(abbreviated as Goldhome Hipot ) was established in 2008, formerly known as the third production enterprise of the national inspection unit, and then through the reform and recombination, we set up the high voltage testing equipment manufacturer.

Goldhome hipot adheres to the” integrity of management, quality-based” concept, dedicated to providing high-quality products and effciency & perfection after-sales service for our all customs,struggling for the global HV power doctor!



  Wuhan Goldhome Hi pot Electrical Co.,ltd(short for Goldhome Hi pot) was established in 2008, its predecessor was state-owned third industry enterprises, one of the earliest enterprises specially in develop, design and manufacture high voltage testing equipment in China.In 2016, merged with Wuhan Sang Electric Co., Ltd. , we realize advantageous compartmentalize and resources reorganization.Now it has become a high-tech enterprise integrating R&D, production, marketing installation and commissioning.1.our-historyOur FactoryGoldhome Hi pot is located in Huading Mould Industrial Park, Economic and Technical Development Zone, Wuhan City, Hubei Province, China, working area more than 4000 square meters.As a high-tech enterprise, we are supported by natural advantages from various research universities in Wuhan city. Goldhome Hi pot works closely with professors from State Grid Power Science Research Institute, Electrical Engineering Colleges of Wuhan University and other scientific research institutions, constantly improving technology and updating products . Now Goldhome Hi pot has more than 20 patented technologies, and many software Copyrights!2.our factory-1product and product applicationOur ProductOur advantage products included AC Resonant Test System, PD Free Test System, AC/DC Hi pot Tester, Primary Current Injection, VLF Hi pot Tester, transformer tester,impulse generator,Transformer oil tester,HV Switch gear Tester ,Insulation Tester,ground Resistance Tester,cable fault locator,relay test set,CT PT analyse,arr ester tester and sf6 gas analyzer,etc.Product ApplicationAll the performance indexes of above testing equipment can reach the leading level in China, widely used in power supply bureau, power plant, power construction, railway, petroleum, chemical industry, metallurgy, coal and other industries.In recent years,our factory continues to expand overseas markets, some competitive products are already exported to American and European countries, Africa, Middle East, etc , and well praised by customers.product applicationOur CertificateAll product process is strictly in accordance with international standards and power industry regulations. And the products are through the national, provincial power authorities testing, as well as CE certification! At present,0ur company has received ISO9001:2015 quality management system certification, ISO14001:2018 occupational health and safety management system certification, and ISO14001:2015 environmental management system certification,and also had got SGS certification.We has more than 20 patented technologies,such as The utility model patent of a frequency conversion series resonance test device,The utility model patent of Lightning impulse voltage testing equipment,The utility model patent of DC high voltage generator,The utility model patent of microcomputer relay protection tester,The utility model patent of High voltage switching characteristic tester., etc.4.certificateoverseas market & our serviceOverseas MarketOur products are sold to Europe, Asia, Africa, North and South America and Oceania, Middle East, etc.and are well received by customers.We had won the bids for the purchase of high-voltage no-partial discharge test equipment from the Polish state-owned insulator production plant, the Myanmar National Grid cable fault tester purchase project, and the high-voltage test equipment purchase project of a Russian power installation and test engineering company.We also sell to end customers, and a single device can also be sold. For example, there are power maintenance and installation companies in Indonesia, South Africa, Denmark, and South Korea, and universities and research institutions purchase and use our test equipment.At the same time, our sales targets also include agencies. At present, we already have cooperated with agents in Singapore, Israel, Mauritius , etc.We insist on providing customers with first-class products and first-class services with reliable product quality and perfect service team.5market-1Our service1.Strict factory testAll products will be assembled and test strictly accord with our product process standard. All qualified products will be issued factory release reports and certificate labels.Defect products or non-qualified products won’t be allowed to make deliver.2.Providing technical materialsDuring the product acceptance, we provide the related manual sheets, packing list,qualified certificate labels, factory test reports and other technical documents.3. Support technical guidanceWe also provide the training for the operators. Complete training includes the skilled operations of our equipment, maintenance and troubleshooting . it also ranges the commissioning and test of our products at site!After-sale service1.First-use responsibility systemAfter the product is delivered, the technician can guide the operation at site if the client requires, and be responsible for the first use of each part2.One year warrantyAll products warranty is 1year, life-time maintenance .During the warranty period, if any defects or damaged because of product’s quality, maintenance or replacement can be provided with free charge in order to let our client’s satisfied !3.TroubleshootingIf the troubleshooting is not difficult, and client can handle with it by themselves, we can offer the call-on line guide within 1 hour!If the troubleshooting is difficult to handle with for client, we can promise that the best solution can be provided within 24 hours!
Similar Product Recommend