Membership
Help
Switech Electronics Co., Ltd.
Switech Electronics Co., Ltd.
No. | Name | Material |
1 | CACE | diallyl phthalate(DAP)(UL94V-0) |
2 | ACTUATOR | Nylon |
3 | HOUSING | Copper alloy |
4 | SWITCH SUPPORT | Copper alloy, tin plated |
5 | END CONTACTS | Copper alloy |
6 | CENTER CONTACTS & ALL TERMINALS | Copper alloy |
7 | TERMINAL SEAL | Epoxy |
1.4.1 This series carry the UL approvals and c-UL(the same effect with CSA)
1.4.2 E123142 The File no. of UL:E123142
1.4.3 TS40-3 The applying category no. of UL: TS40-3
1.Digital Products: digital camera, digital video and so on;
2.Remote Control: the remote control of auto domestic security products;
3.Communication Products: phone, vehicle-mounted phone, telephone set, building equipment, PDA and so on;
4.Homehole appliances: TV set, microwave oven, electric rice cooker, electric fans ,refrigerator,washer;air-conditioning and so on;
5.Security Products: visual interphone, monitor and so on;
6.Toys: electric toys and so on;
7.Computer Products: PC camera and so on;
8.Exercises Machines: treadmills, massage armchair and so on;
9.Medical Device: sphygmomanometer, thermometer, hospital call system and so on;
10.Others: laser pen ,Pointer,Wireless mouse remote control pen,Laser projection pen,page turner,electronic pen;MousePen;overhead projector and so on;
11.Operating switches in all types of electronic equipment such as audio devices, office devices, communication devices, measuring instruments, TVs, video recorders,automotive sets, etc.
12.Household appliances, electric force, telecommunications, machine tool, vessel, textile, printing, Mining machine, Music Instrument, etc.
This specification describes sub-miniature slide switch mainly used as small current and signal switch of electric device with the general required of mechanical and characteristics.
Type: TS40-S-SWTS-4S-CQ-E
RATING: [ protected] 125VAC or 28VDC
FUNCTION: 1P2T
1.1 GENERAL CHARACTERISTICS
1.1.1 Application This specification is applied to T40-S Silde Switch used for electronic equipment.
1.1.2 Operating temperature range -30℃ + 85℃
1.1.3 Test conditions Unless otherwise specified. The atmospheric conditions for making measurements and tests are as follows
Ambient temperature: 5~35℃
Relative humidity: 45~85%
Air pressure: 86~106kPa (860~1060 mbar)
1.2 Appearance construction and dimensions
1.2.1 Appearance Switch shall have good finishing, and no rust crack or plating failures.
1.2.2 Construction and dimensions Refer to individual product drawing.
peculiarity | ITEM | DESCRIPTION | TEST CONDITION | REQUIREMENTS |
电气特性 | 1.3.1 | Visual Examination | By visual examination check without any pressure and testing | There shall be no defect that affect the function of the product |
1.3.2 | Contact Resistance | (1)To be measured between the two terminals associated with each switch pole. (2)Measurements shall be made with a 1kHz shall current contact resistance meter. | 20mΩ MAX(initial) | |
1.3.3 | Insulation Resistance | 500VDC,1min±5sec | 1000MΩ MIN | |
1.3.4 | Dielectric withstanding voltage | 1500VAC (50Hz or 60 Hz) shall be applied between all the adjacent terminals and between the terminal and the frame for 1 minute. | There shall be no breakdown or flashover | |
机械特性 | 1.3.5 | Operating Force | Applied in direction operation ON→OFF OFF→ON
| 10N max |
1.3.6 | Stop Strength | A static load of 30N is applied in the operating direction and pulling direction operated for a period of 30 seconds. | There shall be no sign of damage mechanically | |
1.3.7 | Soldering Heat Resistance | (1) Soldering Temperature:260±5°C (2) Duration of Solder Immersion:5±1 sec (3) Frequency of Soldering Process,2 times Max PCB is 1.6mm in thickness | As show in item2.1.2~2.1.6 | |
耐久性 | 1.3.8 | Operation Life | Measurements shall be made following the test set forth below: 1.5A,250V resistive load Rate of Operation:6~8cycles/minute Cycle of Operation:6000cycles | As show in item 2.1.3~2.1.4 |
耐候性 | 1.3.9 | Resistance Low Temperature | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made Time:48 hours | As show in item2.1.2~2.1.6 |
1.3.10 | Resistance high Temperature | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made Time:48 hours | ||
1.3.11 |
Resistance Humidity | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made Relative Humidity:90-95% Time:48 hours | 1.As show in item2.14~2.1.62. Contact Resistance:100mΩ max 3.Insulation Resistance:10MΩ min |
■ Condition for soldering

■ Manual soldering:
Soldering Temperature | MAX.350℃ |
Continuous Soldering Time | 3秒以下 MAX.3 seconds |
■ Precautions in Handling:
1.Care should be exercised so that flux from the upper part of the printed circuit board does not adhere to the switch.
2.Don’t wash switch body.
