Welcome Customer !

Membership

XwbooInstrumentationTesting MachineOther Testing MachinesWireless Phase Tester
  • $item.Title
  • $item.Title

Wireless Phase Tester

Wuhan Goldhome Hipot Electrical Co., Ltd.

Model
Nature of the Manufacturer
Manufacturer
Product Category
Other Testing Machines
Place of Origin
HuBei, WuHan
HMEC-2 Wireless Phase Tester,for MV overhead distribution circuit ,used for detection of high-voltage power grid closing point on both sides of the phase sequence is the same. Two power line connection before must check phase sequence, or line may be short circuit. The instrument suitable for...
I.Products introduction


HMEC-2 Wireless Phase Tester,for MV overhead distribution circuit ,used for detection of high-voltage power grid closing point on both sides of the phase sequence is the same. Two power line connection before must check phase sequence, or line may be short circuit. The instrument suitable for 380V ~ 220KV power transmission line, and can test whether line charged. The Instrument adopts the wireless transmission technology, safe and reliable operation, easy to use.



II.Working principle


The instrument consists of two transmitters (x and y) and a receiver. Two emitters can be judged whether line charged, and launch phase signal. Receiving meter receives two emitters’ signal, to judge whether the same on both sides phase sequence.



III.Security matters


1.Insulating rod before using should be voltage withstand test.


2.The standard configuration insulating rod length is 3 m, corresponding voltage for ≤ 220 KV. If the measurement circuit voltage higher than 220KV, please use the length of more than 3 meters of the insulating rod.


3. Operation hand position not more than insulating rod handle position.



IV.Technical characteristic


1.Accuracy:When phase sequence is same: the error≤ 5 °.

2.The frequency accuracy:±0.1HZ.

3.Measuring voltage range is 380V - 220KV .

4.The transmitter and the receiving host transmission distance is more than 130 meters, the maximum distance between the two transmitters is about 260 meters.

5.Results (in phase, interphase) using A standard, phase difference acuity ≥30 ° for out phase, the phase difference < 30 ° are in phase.

6.Human voice prompt, male voice "in phase", female voice "phase-out".

7.Screen shows two lines at the same time of phase difference, frequency, waveform and the vector diagram.

8.The host shows battery, half an hour without automatic shutdown operation.

9.Two emitter and receiver use rechargeable lithium battery.

10.Have high pressure test report and the function of the phase sequence.

11.High pressure when measuring the leakage current < 10 uA.

12.Transmitter power consumption < 0.1 W, receiving host work power consumption < 0.3 W.

13.Host lithium battery capacity is about 2200 mAH, transmitter battery capacity is about 350 mAH.

14.Working environment: temperature - 35 ℃ ----- + 45 ℃ ; humidity ≤ 95% RH.

15.Storage conditions: temperature - 40 ℃ ------ + 55 ℃ ; humidity ≤95% RH.

16.The weight:about 3.6KG.

17.Instrument package size: 56 cm long * wide 26 cmm * 13 cm high.


V. Introduction of instrument


(1)Introduction of instrument appearance

detail

(2)Introduction of instrument operation

details 2

Lamp:

(a) “Different” light: two line phase sequence is different.

(b) “Same” light: two line phase sequence is same.

(c) “Charging” light: Battery is charging.

(d) “Full” light: Battery is fully charged.


Key:

(1) long pressing to switch on up or shut down.

(2) Short press the close distance measurement and distance measurement switching.

Supplement:

1)Top right corner have power indicator.

2)The bottom jack is charging interface.

details 4

Lamp:

Testing: Two lights kept flashing.

Charging: fog lamp is red.

Charging complete: fog lamp is green.

Buzzer:

Exposure to high voltage electric lines the buzzer rang 2 seconds, said the line charged.

Install screw hole:

To connect with Telescopic insulating rod.

Charging jack:

To connect with the charger.


(3) The instrument examination method:

Method 1: using the configuration of the emitter mains special test line reference figure (1) connection, 220 v mains plug. If the emitter buzzer, two light is flashing, receiving host shows the frequency of the corresponding information, the transmitter and the host are normal.

details5


Method 2: the emitter hooked up to the corresponding voltage grade of electric circuit inspection (as shown in figure 2) or use the high pressure test equipment, simulation of high voltage line for inspection instruments (as shown in figure 3). If the emitter buzzer, two light is flashing, receiving host shows the frequency of the corresponding information, the transmitter and the host are normal.

details 6

Tip: 1) transmitter direct contact with high pressure, apparatus started about 4 kv voltage.

2) use mains special test line, equipment start-up voltage of about 5 v


  Wuhan Goldhome Hi pot Electrical Co.,ltd(short for Goldhome Hi pot) was established in 2008, its predecessor was state-owned third industry enterprises, one of the earliest enterprises specially in develop, design and manufacture high voltage testing equipment in China.In 2016, merged with Wuhan Sang Electric Co., Ltd. , we realize advantageous compartmentalize and resources reorganization.Now it has become a high-tech enterprise integrating R&D, production, marketing installation and commissioning.1.our-historyOur FactoryGoldhome Hi pot is located in Huading Mould Industrial Park, Economic and Technical Development Zone, Wuhan City, Hubei Province, China, working area more than 4000 square meters.As a high-tech enterprise, we are supported by natural advantages from various research universities in Wuhan city. Goldhome Hi pot works closely with professors from State Grid Power Science Research Institute, Electrical Engineering Colleges of Wuhan University and other scientific research institutions, constantly improving technology and updating products . Now Goldhome Hi pot has more than 20 patented technologies, and many software Copyrights!2.our factory-1product and product applicationOur ProductOur advantage products included AC Resonant Test System, PD Free Test System, AC/DC Hi pot Tester, Primary Current Injection, VLF Hi pot Tester, transformer tester,impulse generator,Transformer oil tester,HV Switch gear Tester ,Insulation Tester,ground Resistance Tester,cable fault locator,relay test set,CT PT analyse,arr ester tester and sf6 gas analyzer,etc.Product ApplicationAll the performance indexes of above testing equipment can reach the leading level in China, widely used in power supply bureau, power plant, power construction, railway, petroleum, chemical industry, metallurgy, coal and other industries.In recent years,our factory continues to expand overseas markets, some competitive products are already exported to American and European countries, Africa, Middle East, etc , and well praised by customers.product applicationOur CertificateAll product process is strictly in accordance with international standards and power industry regulations. And the products are through the national, provincial power authorities testing, as well as CE certification! At present,0ur company has received ISO9001:2015 quality management system certification, ISO14001:2018 occupational health and safety management system certification, and ISO14001:2015 environmental management system certification,and also had got SGS certification.We has more than 20 patented technologies,such as The utility model patent of a frequency conversion series resonance test device,The utility model patent of Lightning impulse voltage testing equipment,The utility model patent of DC high voltage generator,The utility model patent of microcomputer relay protection tester,The utility model patent of High voltage switching characteristic tester., etc.4.certificateoverseas market & our serviceOverseas MarketOur products are sold to Europe, Asia, Africa, North and South America and Oceania, Middle East, etc.and are well received by customers.We had won the bids for the purchase of high-voltage no-partial discharge test equipment from the Polish state-owned insulator production plant, the Myanmar National Grid cable fault tester purchase project, and the high-voltage test equipment purchase project of a Russian power installation and test engineering company.We also sell to end customers, and a single device can also be sold. For example, there are power maintenance and installation companies in Indonesia, South Africa, Denmark, and South Korea, and universities and research institutions purchase and use our test equipment.At the same time, our sales targets also include agencies. At present, we already have cooperated with agents in Singapore, Israel, Mauritius , etc.We insist on providing customers with first-class products and first-class services with reliable product quality and perfect service team.5market-1Our service1.Strict factory testAll products will be assembled and test strictly accord with our product process standard. All qualified products will be issued factory release reports and certificate labels.Defect products or non-qualified products won’t be allowed to make deliver.2.Providing technical materialsDuring the product acceptance, we provide the related manual sheets, packing list,qualified certificate labels, factory test reports and other technical documents.3. Support technical guidanceWe also provide the training for the operators. Complete training includes the skilled operations of our equipment, maintenance and troubleshooting . it also ranges the commissioning and test of our products at site!After-sale service1.First-use responsibility systemAfter the product is delivered, the technician can guide the operation at site if the client requires, and be responsible for the first use of each part2.One year warrantyAll products warranty is 1year, life-time maintenance .During the warranty period, if any defects or damaged because of product’s quality, maintenance or replacement can be provided with free charge in order to let our client’s satisfied !3.TroubleshootingIf the troubleshooting is not difficult, and client can handle with it by themselves, we can offer the call-on line guide within 1 hour!If the troubleshooting is difficult to handle with for client, we can promise that the best solution can be provided within 24 hours!
Similar Product Recommend