Superfine Vertical Mill

NegotiableUpdate on July 04

Model

Nature of the Manufacturer: Other

Product Category: Vertical mill

Place of Origin: City, Province

Online Consult Contact Information

Overview

[Maximum feed]: 20mm[Maximum output per unit]: 10 (2500 mesh)[Motor power]: 280[Application range]: Ultrafine powder production line[Applicable materials]: limestone barium sulfate quartz sａnd etc.

Product Details

Product introduction

TLUM series super-fineness vertical mill is my company combined with all kinds of grinding machine production experience for many years on the basis of vertical mill widely absorbs the superfine grinding theory at home and abroad design and development of advanced grinding equipment. A complete is a kind of super fine powder grinding classification transmission in the integration of superfine pulverizing industry professional equipment can be widely used in industry chemical industry metallurgy non-metallic mineral industry etc. To mohs hardness density in 3.2 the following below level 5 compressive strength is less than 150 mpa non flammable and explosive mines non-corrosive brittle materials required by the granular and powdered materials into ultrafine powder (325 ~ 2500 mesh).Usually applied to materials are as follows: calcite barium sulfate calcium carbonate talc wollastonite pyrophyllite and dolomite graphite kaolin limestone etc.

Structure principle

TLUM series Super-fineness vertical mill is mainly composed of motor reduction drive roller device mill equipment pressure device classifier the body gas station a host of PLC electrical control system and other parts. Main motor by rotational speed reducer drive a millstone the wind from the air inlet into the roller mill in the body at the same time the material through the screw feeder fell in the middle of the mill feed opening under the action of centrifugal force central to the edge of the uniform moving materials from a millstone while area through the mill wheel grinding roller roller rolling large materials directly crushed fine grained material by extrusion forming on the intergranular crush on bed. Shattered as it continues to move mill edge material until being taken away by the wind ring in strong turbulence and larger particles material again fell to the mill to continue to crush flow of materials through the upper part of the separator in under the action of rotor blade coarse particle back grinding mill qualified fine powder with airflow mill the system sets collected powder was collected by the powder of the products is the vertical grinding machine grinding. Mix materials of iron and other debris along with the material movement to mill edge because its weight rather than by the wind fell to mill inferior vena is installed in the mill at the bottom of the scraping plate into the slag discharge mouth closed. By adjusting the rotational speed of multiple classifier rotor can get different fineness of qualified products. By adjusting the pressure of the hydraulic system can adjust roller pressure can adapt to different hardness of raw materials in certain ranges.

1: Main motor 2: Roller dilute gas station 3: reducer 4: engine base(Inlet)

5: millstone device 6: grinding roller 7: Cone funnel 8: Multiple separator

9: Engine body 10: Screw feeder 11: limit device

12:Pressure device (hydraulic cylinder) 13: Hydraulic station 14 :Reducer dilute gas station

Technical advantage

layers in grinding principle high whiteness and neatness of product

On the principle of vertical grinding abrasive layer material stay in the mill time is short reduce repeat grinding. The product contains iron very small and is used for grinding white or transparent materials the whiteness and neatness of the product is high. The grinding of lining board of the special design of roller shell and curve easier to form powder abrasive layer.

Roller separate lubrication double oil pump

Roller lubrication using separate lubrication station and a single roller loop adopts double pump pump suction work mode at the same time both make full lubrication and cooling of the roller bearing roller bearing and can guarantee indoor not too much oil due to the leakage.

German alpine choose powder technology can achieve the required a one-time fineness

With German alpine long classifier principle of each rotor can frequency control of motor speed the grinding fineness of finished product can be implemented in selected scope can need not through second grade of air separation without the presence of low grade material.Finished product granularity is smaller than 2 microns particles content high the highest cocoa was 70% and 325 mesh low residual also suitable for secondary sorting out a finer grain size of the finished product.

Automation control frequency control of motor speed energy saving efficiency

PLC/DCS automatic control roller pressure control method the grinding pressure get accurate control and does not need manual operation.Host to host range of PLC electrical control system of electrical components an orderly work coordination commａnd host speed adopts frequency control of motor speed compared with any other form of mill to save energy consumption by 30% ~ 50% excellent economic benefit.

Latest case

Two sets of TLZJ1100 ultra-fine vertical grinders manufactured by Tongli Heavy Machinery Co. Ltd. were successfully put into operation in Xinjiang *** New Building Materials Co. Ltd. - artificial granite project.

Production status

[Day operation]: 24 hours

【Feed】: Calcite particle size 5-10mm

[Product]: Fineness: 325-1250 mesh

[Production]: 8-15 tons / hour

【client feedback】:

The ultra-fine vertical mills that our company purchased at the same time not only ensure the quality but also the production is particularly stable efficient and environmentally friendly which greatly improves the company's production capacity. In the first year of use it has created a net profit of 2 million for the company.

Technical parameter

Specifications	Turntable middle diameter	yield	fineness	Granularity of grinding material	Moisture content of grinding material	Main motor power （KW）	Number of grinding rolls	Power X number of multi head pulverized machine	Reference weight
TLUM1125	1100	5~12	400~1250	<10 mm	<3%	250	3	15 KWx5	48
TLUM1232	1200	7~16	400~1250	<10 mm	<3%	315	3	15 KWx7	68
TLUM1436	1400	8~18	400~1250	<10 mm	<3%	355	3	15 KWx7	90