Welcome Customer !

Membership

Company Name: Shenzhen gooderly Technology Co., Ltd
Free Member ·1YRS
,
Other

Main Products: 传感器、变送器

Xwboo>Products

VEC20 series electromagnetic flowmeter

Model
Nature of the Manufacturer
Other
Product Category
Baffle flow switch
Place of Origin
City, Province
Overview
VEC20 series electromagnetic flowmeter
Product Details

Product introduction

VEC20 series electromagnetic flowmeter is a kind of induction meter to measure the volume flow in the pipe conducting medium according to Faraday's law of electromagnetic induction, the sensor has the advantages of simple structure, measurement without hindrance liquid flow part tube, so when the fluid flow through the timing does not cause any additional pressure loss and flow rate, is one of the lowest flow meter the operating energy meter, which can be widely used in petroleum, chemical industry, water conservancy, metallurgy, textile, papermaking, environmental protection, food and other industries and municipal administration, water conservancy construction, river dredging and other fields of traffic.


Working principle:

The measuring system of the VEC20 series electromagnetic flowmeter is based on Faraday's law of electromagnetic induction, that is, when the conductor cuts magnetic line in the magnetic field, it induces induction electromotive force at both ends. As shown in the figure, the conductive liquid flow in perpendicular to the magnetic field of non magnetic measuring tube, produce EMF ratio and flow perpendicular to the direction of flow direction, the direction of electromotive force according to the "Fleming rule of right hand",
Its value is as follows: E=KBVD
E----- induction electromotive force,
K----- coefficient;
B----- magnetic induction intensity,
V---- measurement of the average velocity in the tube section
The inner diameter of D---- measuring tube
VEC20 series electromagnetic flowmeter at work, fluid flow through the vertical direction of the magnetic field and fluid flow, induced a proportional to the average velocity of the liquid electric potential of conductive liquid, the induction electromotive force through the detected installed in the wall of the two electrodes, the shielded cable is transmitted to the converter, the converter after the operation, then the instantaneous flow, total flow, velocity signal is displayed on the display screen, can also be converted into 4-20mA signal.

Product advantages:

1) the sensor structure of the electromagnetic flowmeter is simple, and there is no throttle component in the measurement tube that is obstructing the flow of the fluid. It does not cause any loss of energy of the fluid will not cause blockage, is one of the lowest energy consumption meter flow meter, particularly suitable for measuring wear with solid particles, large slurry, cement slurry and liquid-solid two-phase flow and various fiber and pulp suspension liquid liquid etc..
2) the electromagnetic flowmeter contacts the liquid only by measuring the lining and electrode of the pipe. The material can be selected according to the nature of the fluid being measured, and can be widely used with various fluids. For example, using polyvinylidene fluoride or polytetrafluoroethylene as lining, it can measure various corrosive media such as acid, alkali and salt. The wearable rubber can be used as an inner liner to measure the fluid with wear properties. Three
3) electromagnetic flowmeter is a volume flow measuring instrument. During the measurement process, it is not affected by the temperature, viscosity and density of the tested medium with electrical conductivity (within a certain range). Therefore, just as water electromagnetic flowmeter calibration, will be used to measure other conductive liquid flow.
4) the output of an electromagnetic flowmeter is only proportional to the average velocity of the measured medium, but has nothing to do with the flow state (laminar or turbulence) under the symmetrical distribution. So the range of the electromagnetic flowmeter is very wide, its measurement range is up to 100:1, and some even reach the operating flow range of 1000:1.
5) the electromagnetic flowmeter has no mechanical inertia, the reaction is sensitive, and the instantaneous pulsation flow can be measured.
6) low installation requirements. As long as the front tube is more than 5D, the rear tube is more than 2D (D is the inner diameter of the instrument).

roduct introduction

1, current output: 4-20mA, load impedance 0-750 Omega basic error 0.1%+ + 0.1 mu A
2. frequency output: 1-5KHz, photoelectric isolation,
3. pulse output: 0.001 - 1.000m3/cp, 0.001 - 1.000Ltr/cp photoelectric isolation
4. alarm output: an on-line alarm, a lower limit alarm, a photoelectric isolation
5. communication mode: RS485 or CAN bus
6, repeatability error: the measured value is 0.1%
7, precision grade: pipeline type: level 0.5, 1
8, the measured medium temperature: ordinary rubber lining: -20~+60 C
High temperature rubber lining: -20~+90 C
Polytetrafluoroethylene lining: -30~+100 C
High temperature tetrafluoro lining: -40~+180 C
9, rated working pressure: pipeline type: DN10 ~ DN80: 4Mpa
DN100: = 1.6Mpa ~ DN150
DN200: = 1Mpa ~ DN1000
DN1200: = 0.6Mpa ~ DN2400
10. Flow measurement range: the range of flow measurement range is 0.1 ~ 15m/s

11, electrode materials: Molybdenum Stainless steel, titanium (Ti), tantalum (Ta), Hart alloy (H), platinum (Pt), or other special electrode materials
12, protection grade: IP68, IP67, IP65
13, power supply: AC 85~265V, 45~63HZ 5%, 16VCD---36VCD 14 DC harmonic optional length straight pipe type: the upstream is larger than 5DN, lower than 2DN
15, connection mode: the flowmeter and the piping are all flanged connections. The size of the flange connection should comply with the regulations of GB119-88 16, the riot mark is mdllBT4, and the integral flameproof design is adopted.
17, ambient temperature: -25 C ~+60 C
18. Relative temperature: 5%~95%
19. Consumption of total power: less than 20W
20, the measured medium temperature: ordinary rubber lining: -20~+60 C
High temperature rubber lining: -20~+90 C
Polytetrafluoroethylene lining: -30~+100 C
High temperature tetrafluoro lining: -40~+180 C