Welcome Customer !

Membership

Jiangsu Xingxing Drying Equipment Co.,Ltd.
Free Member ·1YRS
ChangZhou,JiangSu
Manufacturer

Main Products: Dryer

Xwboo>Products

Jiangsu Xingxing Drying Equipment Co.,Ltd.Free·1YRS

  • E-mail

    zar.dangxian@jxxcn.com

  • Phone

    0086-519-88903988

  • Address

    Jiaoxi Industrial Park, Tianning District, Changzhou City

Contact Now

Spray Dryer

Model
Nature of the Manufacturer
Manufacturer
Product Category
Drying Equipment Series
Place of Origin
City, Province
Overview
Product Introduction:   Centrifugal spray dryers, spray dryers, and spray drying towers are widely used processes in the liquid forming process and drying industry. It is especially suitable for produci...
Product Details

Overview:

  Centrifugal spray dryers, spray dryers, and spray drying towers are widely used processes in the liquid forming process and drying industry. It is especially suitable for producing powdery and granular solid products from suspoemulsion, solution, emulsion and pasty liquid raw materials. Therefore, when the particle size distribution, residual moisture content, bulk density and particle shape of the finished product meet the standard of ^, the spray dryer is a better drying process.

Features:

1. The spray drying speed is fast. After the material liquid is atomized, the surface area is greatly increased. In the process of contact with hot air, 95%-98% of the water can be evaporated instantly, and the drying time is only a few seconds, especially suitable for heat-sensitive materials The dryness. To

  2. The product has good uniformity, fluidity and solubility. The higher the purity of the product, the better the quality. To

  3. The spray dryer production process is simplified, and the operation and control are convenient. For liquids with a moisture content of 40-60% (up to 90% for special materials), the liquid can be dried into powder products at one time. After drying, there is no need to pulverize and screen, which reduces the production process and improves the product purity. The product particle size, bulk density and water content can be adjusted by changing the operating conditions within a certain range, and the control and management are very convenient.

Working principle:

The spray dryer has an open cycle, parallel flow, and centrifugal atomization. The drying medium air is filtered by the primary and medium-efficiency air filters and is sucked by the blower according to the operating instructions, then heated by the heater and passed through the hot air distributor of the high-efficiency filter into the spray drying main tower. The liquid material passes through the peristaltic pump according to the operating instructions, enters the high-speed rotating centrifugal nozzle, and is dispersed into small droplets under the action of centrifugal force. In the spray drying main tower, the small droplets are in full contact with the hot air, and they are dried into products after heat exchange along their specific paths, and then separated by a cyclone separator, the solid materials are collected, and the gas medium is filtered and discharged . The entire spray system is easy to clean, has no dead ends, and meets GMP requirements.

The following three aspects in design and manufacturing are important points for attention

1. The contact of hot air flow and mist droplets: When a sufficient amount of hot air flow enters the spray drying chamber, the direction and angle of the hot air flow must be considered, whether it is cocurrent, countercurrent or mixed flow, to ensure sufficient contact with the mist droplets. Full heat exchange.

2. Atomization: The atomization system of the spray dryer must ensure uniform droplet size distribution, which is very important. Because in this way, the pass rate of product quality can be ensured.

3. Design of pipe angle and cone angle

Application scope:

Chemical products: polyaluminum chloride, disperse dyes, reactive dyes, organic catalysts, white carbon black, washing powder, zinc sulfate, silicon dioxide, sodium metasilicate, potassium fluoride, calcium carbonate, potassium sulfate, inorganic catalysts, various Kind of waste liquid and so on.

Food products: amino acids, vitamins, egg powder, bone meal, condiments, protein, milk powder, pig blood powder, soy sauce powder, coffee, tea, glucose, potassium sorbate, pectin, flavors and spices, vegetable juice, yeast, starch Wait

  Ceramics Porcelain: alumina, zirconia, magnesia, titania, magnesia titania, pottery clay, porcelain clay, various ferrites and metal oxides, etc.


Item/Model(LPG)

5

25

50

100

150

200

500

800

1000

2000

3000

4500

6500


Inlet temperature(℃)

140-350 Self-control


output temperature(℃)

80-90


Spray pattern

High-speed centrifugal atomizer (mechanical transmission or stepless variable frequency speed regulation are available)


Evaporation of water(kg/h)

5

25

50

100

150

200

500

800

1000

2000

3000

4500

6500


Atomizer speed(rpm)

25000

22000

21500

18000

16000

12000-13000

11000-12000


Diameter of atomization disc(mm)

60

120

150

180-210

Determined according to process requirements


Upper limit of electric heating power(k w)

8

31.5

60

81

99

Equipped with other heat sources


Dry powder recovery rate(%)

Approximately 95


Occupation length(m)

1.6

4

4.5

5.2

7

7.5

12.5

13.5

14.5

According to the technological process,

Site conditions and user requirements are determined


Occupation width(m)

1.1

2.7

2.8

3.5

5.5

6

8

12

14


Tower height(m)

1.75

4.5

5.5

6.7

7.2

8

10

11

15


Nozzle hoisting height(m)

- -

2.5

2.5

3.2

3.2

3.2

3.2

3.2

3.2


Note: The above data is for reference only. The amount of water evaporation is related to the characteristics of the material, the solid content and the temperature of the hot air inlet and outlet. The user can select the heating method according to the local energy situation, and the dust collection and dust removal method according to the material characteristics.