-
E-mail
amy@safeinvert.com
- Phone
-
Address
#22 Liujiang Avenue, Liushi Town, Yueqing City, Zhejiang Province, China
Membership
Help
Zhejiang Saikong Electrical Technology Co., Ltd.Free·1YRS
amy@safeinvert.com
#22 Liujiang Avenue, Liushi Town, Yueqing City, Zhejiang Province, China
What is the difference between a high pressure soft starter and a low pressure soft starter?
There is a phenomenon in the soft starter industry that deserves attention: although the principles of high-voltage soft starters and low-voltage soft starters are basically the same, the demand for high-voltage soft starters is increasing and there are fewer real manufacturers. Why is this?
In fact, there are differences between high-voltage soft starters and low-voltage soft starters. High-voltage soft starters have particularities. It is these particularities that make many low-voltage manufacturers unable to make high-voltage products. So what is the difference between them?
1. The insulation performance of electrical components must be good. The high-voltage soft starter works in a high-voltage environment, which requires high insulation of electrical components and strong anti-interference ability of electronic chips. And during assembly, the layout of electrical components and the connection between the high-voltage soft starter and other electrical equipment are very important.
2. High-performance control core. There must be a high-performance control core in the high-voltage soft starter, which can process the signal in time and quickly. This control core generally uses a high-performance DSP chip, rather than an ordinary single-chip core of a low-voltage soft starter. Due to the insufficient withstand voltage capability of a single high-voltage thyristor, multiple high-voltage thyristors must be connected in series to divide the voltage in a high-voltage soft starter. However, the performance parameters of each thyristor cannot be completely consistent, which will lead to the damage of the thyristor. Therefore, when selecting thyristors, it is necessary to ensure that the thyristors of each phase are as consistent as possible, and the parameters of the RC filter circuit components of the thyristors of each phase are as consistent as possible.
3. The thyristor is triggered, which is a major difficulty for high-voltage soft starters. Since the main circuit has multiple thyristors, each thyristor needs a trigger board to complete the triggering. Trigger circuits come in two forms:
(1) The trigger circuit is isolated from the main circuit. There are two types of isolation components: one is to use optocouplers, but optocouplers have dead zones when they are turned on and off. Under high voltage conditions, whether it is start-up or soft-stop, it is not easy to achieve. And because a single optocoupler has insufficient withstand voltage, optocouplers must be connected in series, but the inconsistency of each optocoupler will lead to the risk of breakdown under high voltage conditions. Although low-voltage soft starters are very convenient and effective in this way, there are still many difficulties under high-pressure conditions. One way is to use a pulse transformer. This method is relatively mature and reliable. The pulse is input on the primary side of the pulse transformer, and the pulse wave generated on the secondary side is added between the gate and the cathode of the thyristor to complete the trigger. The time ratio of the high level and the low level of the trigger pulse is also very important. The high level time is long, which consumes a lot of power on the trigger board, and the high level time is short, which cannot fully turn on the thyristor. Due to the power limitation of the pulse transformer, this method has certain difficulties in triggering the super-power thyristor. However, it can be achieved by properly processing the primary pulse wave of the pulse transformer.
(2) The trigger circuit has an equipotential with the main circuit. This method avoids the power limitation of the pulse transformer, but requires higher processing of the trigger circuit. No matter what kind of trigger circuit, a good trigger power supply is required, and this power supply supplies power to multiple trigger boards. First, the power supply must be very stable, and secondly, the power supply can adjust itself and adapt to the triggering of thyristors of various powers. How much energy is needed to fully trigger the thyristor, neither too much nor too much. If you give too much, the thyristor will be burned out, and if you give too little, the thyristor will not be turned on.
4. Ensure safe and reliable transmission of trigger signals. Because the working environment of the high-voltage soft starter is susceptible to various electromagnetic interference, when transmitting the trigger signal, optical fiber transmission is generally used, one is multi-fiber mode, and the other is single-fiber mode, which can effectively avoid various electromagnetic interference.
5. Signal detection requirements are higher. There is a lot of electromagnetic interference in the environment where the high-voltage soft starter is located, and the vacuum contactor and vacuum circuit breaker used in it will generate a lot of electromagnetic interference during the breaking and closing process. Therefore, the high-voltage soft starter not only needs to perform hardware filtering on the detected signal, but also perform software filtering to remove the interference signal.
6. How to smoothly switch to the running state after completing the starting process. This is a difficulty with soft starters. It is very important to select the correct bypass point: the bypass point is early, the current impact is very large, even under low voltage conditions, it will cause the circuit breaker in the three-phase power supply to trip, or even damage the circuit breaker, and the damage is even more harmful under high voltage conditions. The bypass point is late, and the motor shakes badly, which affects the normal operation of the load.