Welcome Customer !

Membership

Zhejiang Saikong Electrical Technology Co., Ltd.
Free Member ·1YRS
,
Other

Main Products: 变频器

Xwboo>Technical Article>How to configure the power of photovoltaic modules and grid-connected inverters?

Zhejiang Saikong Electrical Technology Co., Ltd.Free·1YRS

  • E-mail

    amy@safeinvert.com

  • Phone

  • Address

    #22 Liujiang Avenue, Liushi Town, Yueqing City, Zhejiang Province, China

Contact Now
How to configure the power of photovoltaic modules and grid-connected inverters?
Date: 2022/11/3Read: 42

How to configure the power of photovoltaic modules and grid-connected inverters?

Oct 26, 2021

How to configure the power of photovoltaic modules and grid-connected inverters?

In the photovoltaic grid-connected system, the power of the module is related to the inverter, and the power matching of the module and the inverter is not a fixed ratio of 1:1. It needs to be considered in combination with the specific conditions of the project. The main influencing factors are radiation. Power, system loss, inverter efficiency, inverter life, inverter voltage range, component installation angle, etc.


1. The inclination and azimuth angle of component installation


When the plane of the object is completely perpendicular to the light, the received power is the largest. If the object is placed at an angle, the plane of the object and the light will be at a certain angle, and the received power will be discounted. For the same area, the received power will be much less. The angle between the module and the sun is perpendicular, and the power is maximum.


2. The irradiance of the installation area


The output power of the module is related to the irradiance. In areas with good solar energy resources, due to the fact that there are few clouds on sunny days, good air quality, and high atmospheric transparency, the solar radiation reaching the surface of the module is much higher than the average value of areas with poor resources.


3. Installation altitude


The higher the altitude, the thinner the air, and the smaller the weakening effect of the atmosphere on solar radiation, the stronger the solar radiation reaching the ground. For example, the Qinghai-Tibet Plateau is the region with the strongest solar radiation in China. Where the air is thinner, the heat dissipation of the inverter will be worse. If the altitude exceeds a certain height, the inverter must be derated.


4. DC side system efficiency


In a photovoltaic system, energy is radiated from the sun to photovoltaic components, and reaches the inverter through DC cables, combiner boxes, and DC power distribution. There is loss in all links. Different design schemes, such as using centralized type, string type, distributed type, etc., have very different DC side losses.


5. Inverter heat dissipation conditions


The inverter should generally be installed in a place with good ventilation and avoid direct sunlight, which is conducive to heat dissipation. If due to site restrictions, the inverter has to be installed in a closed place that is not conducive to heat dissipation, the derating of the inverter must be considered, and fewer components should be equipped.


6. Component factors


Positive power tolerance: In order to satisfy that the attenuation of photovoltaic modules does not exceed 20% in 25 years, many module manufacturers have a positive tolerance of 0-5% for modules that have just been shipped. For example, for 265W modules, the actual power that has just been shipped may be 270W.


Negative temperature coefficient: The power temperature system of the module is about -0.41%/℃. When the temperature of the module drops, the power of the module will increase. A 250W module, regardless of equipment loss, in areas with the best sunlight in China, such as northern Ningxia, northern Gansu, southern Xinjiang, etc., the maximum output power may exceed 250W.


Double-sided module: The double-sided module can not only receive the radiation power of the front sunlight, but the back can also receive the reflected radiation power of the sunlight. Different objects have different reflectivity to sunlight in different spectral bands. Snow, wetland, wheat, desert, different features have different reflectivity in the same waveband, and the same feature has different reflectivity in different wavebands.


7. Inverter factors


Inverter efficiency: The efficiency of the inverter is not constant. There are power switching device losses and magnetic losses. When the power is low, the efficiency is relatively low. When the power is 40% to 60%, the efficiency is the highest. When it exceeds 60%, The efficiency gradually decreases. Therefore, the total power of the photovoltaic power should be controlled between 40% and 60% of the inverter power to obtain the best efficiency.


Inverter life: photovoltaic inverters are electronic products, and their reliability has a lot to do with the inverter operating temperature. The temperature of capacitors, fans, relays and other components can increase by 10℃, and the failure rate can increase by more than 50% . The operating temperature is also related to the power. According to statistics, the inverter works at a power of 80-99% for a long time than a power of 40-60%, and its lifetime is about 20% lower.


The optimal working voltage range of the inverter: the working voltage is about the rated working voltage of the inverter, and the efficiency is the highest, single-phase 220V inverter, inverter input rated voltage is 360V, three-phase 380V inverter, inverter The rated input voltage of the converter is 650V.


in conclusion


In some places, the photovoltaic system calculates the system capacity according to the capacity of the module. At this time, the inverter is selected according to the maximum power output by the module to avoid the inverter current limit. According to the actual situation, the module and the inverter can be 0.9 :1 to 1.4:1 to configure. However, in some places, the system capacity is calculated based on the AC output power of the inverter. If the price of electricity is high and the price of the components is quite cheap, in order to increase the power generation as much as possible, the power of the components can be increased. Components and inverters can be configured from 1.4:4 to 1.8:1, depending on how many components the inverter can connect.