Angle Stop Shut-off Turn Valve

JX-0212

• Angle Valve
• Size 1/2″FIP×3/8″OD
• Zinc alloy handle
• 125 PSI cold working pressure
• C37700 materials
• It’s in a plastic bag packed with each
• Three million times open-off working is guaranteed
• 1/2″ FIP X 3/8″ O.D 1/4 Turn Angle Stop Valve
• Shut-Off Brass Angle Stop Valve for Faucets and Toilets
• Shut-off Valve; 1-Piece Body Construction; 1/4-Turn ON/OFF
• 1/4-turn valve operation means only a quarter-turn of the handle
• Suitable for water supply systems, civil construction piping systems
• It can be used as a shut-off valve or water saver valve and installed between the shower arm and the shower head to control the flow of water
• Function: Kitchen, Home, Garden, and General
• Style: Handle-controlled

Introduction: what is an angle stop shut-off turn valve?

An angle stop shut-off turn valve, also known as an angle stop valve or a shut-off valve, is a type of plumbing valve used to control the water flow to a faucet, toilet, shower, or other fixture. Angle stop valves are typically installed under a sink or behind a toilet. They are operated by turning a handle attached to the valve stem.

Angle stop valves are used to shut off the water supply to a fixture when it is not in use. This can be helpful when you need to make repairs to the fixture or when you want to prevent water damage in your home. Angle stop valves are also used to control the water pressure at a fixture. Turning the handle on the valve can increase or decrease the amount of water flowing through the valve.

The many benefits of using an angle stop shut-off turn valve

An angle stop shut-off turn valve is a plumbing type used to control the flow of water in a piping system. It is designed to be installed when a water supply line meets a fixture, such as a sink or a toilet. The angle stop valve has two handles that can be turned to open or close the water flow. When the handles are in the same position, the valve is open, and water will flow through it. When the handles are in opposite positions, the valve is closed, and water will not flow through it.

How to properly install an angle stop shut-off turn valve

If you’re unfamiliar with shut-off valves, an angle stop is a type of shut-off valve installed at an angle, typically 90 degrees. They often control water flow to fixtures like sinks and toilets. Here’s how to properly install one:

1. Begin by turning off the main water supply to your home. This will ensure no water flowing through the pipes while you’re working.

2. Next, locate the shut-off valve that controls water flow to the fixture where you’ll be installing the angle stop. If there isn’t one already, you’ll need to install one before proceeding.

3. Once the shut-off valve is in place, cut into the pipe that supplies water to the fixture using a hacksaw or another cutting tool.

How to troubleshoot common problems with angle stop shut-off turn valves

If your angle stop shut-off turn valve is leaking, you should first check the washer. The washer is located under the handle and may be worn out or loose. To replace the washer, unscrew the handle, remove the old washer, and put in a new one. Make sure the new washer is tight before screwing the handle back on.

If the valve is still leaking after replacing the washer, there may be an issue with the packing nut. The packing nut is under the cap at the top of the valve. Unscrew the cap and tighten or replace the packing nut as needed.

If your angle stop shut-off valve won’t turn off or on, something may be blocking it. First, try to remove any debris that may be caught in it.

Conclusion: the advantages of using an angle stop shut-off turn valve

An angle stop shut-off turn valve is a great way to save money on your water bill. Using this type of valve

In addition, an angle stop shut-off turn valve can help you save water. Turning the water off at the source can prevent water waste. This is good for the environment and can help you save even more money on your water bill.

Finally, an angle stop shut-off turn valve is easy to use. You don’t need any special tools or knowledge to use it. You’re all set to turn the knob to the desired position.

We know that our pipelines supply efficient ways to pass fluid at its designated location. These pipelines usually cover many kilometers to carry fluid to a potential source. These fluids need control over their flow. The flow can be well-acquired with the help of an angle valve.

Angle valves have a diverse range of services and are well known for that. We all encounter their significance and apply angle valves around us. This factor increases angle valves’ need for understanding. For running a plumbing products business, the demａnd rises considerably.

We are moving forward to the next step. For this one, take out the pipe-cleaning brush. Move it well through the first few inches to clean any debris. Small particles might have been left while cutting the pipe. The burst removes such particles and makes a perfect time for the next step.

6. You can also use an emery cloth to clean the pipe. It also helps remove rust surfaces when dealing with old and worn-out pipes. You can find emery cloth in your toolbox or at a nearby store.
7. Here comes the actual work. Take the angle valve out of the wrapping (if you use a new one). If your valve has compressions to fit, you need to install olive sits with a nut. These small fragments of a compression pipe can be bought from Amazon or sanitary stores. Insert the but over the outer surface of the tube. Now place the olive along with it in a particular area. It creates perfect compression for your valve to fit.

You can slide the compression valve by applying the plumber’s putty over it.

8. However, if you use a valve other than compression, you need to slide the valve over the pipe you prepared. And that’s it. You are all done knowing how to install an angle valve.
9. Here comes last but not the minor factor. Turn on the water supply you cut off in the beginning. By doing so, we ensure no leaks in pipes or valves. Turn the valve on and off to notice its functioning. If you don’t see any mishaps, pat yourself on the back. Your angle valve is successfully installed.

How to Replace Angle Valves?

To install something refers to the first-ever implantation. However, replacement occurs when an old valve is not capable of working. Replacing an old angle valve is a fun task you would love to do. If your old angle valve is no longer working, replace it with the instructions mentioned here.