Ultrafine powder spray dryer (customized)
1. Equipment characteristics
- The air atomization spray has small angle and will not collide with the wall.
- Drying to achieve 1-8 micron small particle size powder;
- The normal normal distribution of particle size is steeper and the particle size is more uniform.
- Adjustable particle size
- Material application scope is wider
- The whole atomizing mechanism has no plastic gaskets, no motors, long service life and easy maintenance.
- It can be upgraded to a coating atomizing mechanism for precise steel, and can use various metal materials.
- The atomizing mechanism is easy to disassemble, assemble and clean, and easy to maintain.
2. Equipment superiority
- An innovative airflow atomization structure is adopted in the atomization system. The airflow atomization structure adopts two-hole deviation mechanism to realize two-stage atomization. The uniformity of droplets is good. The particle size can be adjusted according to the two-dimensional curve of QFN-CX-NZY8-075VER2018-1A atomization system.
- The spray nozzle of the atomization system is coated with diamond, which is more wear-resistant than the ordinary SUS304 material. The service life of SUS304 is 10 times higher than that of SUS304.
- It can be upgraded to low temperature spray dryer (with Jo Maple's low temperature drying system QFN-CX-5-MD10), and spray drying is achieved at a minimum of 35 degrees Celsius. It is of great significance for the research and development of new materials. It can achieve spray drying of materials in a large interval of 35-280 degrees Celsius. The spray drying machine with high and low temperature can be realized. It is different from the high temperature spray dryer with a general temperature of 180-280 degrees Celsius.
- Particle size detection (data from customers):
2-D Curve of QFN-PWCX-NZY8VER2018-075A Atomization System
Line reading
1 indicates the spray volume of a nozzle (l/hr).
The red line represents the compressed air PA (MPA), the blue line represents the liquid pressure, the PW (MPA), and the green line represents the QA/QW steam-water ratio.
3. Measurement of 2-D Curves of 4. QFN-PWCX-NZY8VER2018-075A Atomization System by Toplephic Method
Line reading
1 indicates the spray volume of a nozzle (l/hr).
The red line represents the compressed air PA (MPA), the blue line represents the liquid pressure, the PW (MPA), and the green line represents the QA/QW steam-water ratio.
4.The number inside represents the average SAUTER particle size (micron) measured by Toplephine.
QFN-CX-NZY8VER2018-075A atomization system:
For example, if the final average dry powder size is about 3 microns, the known condition is that the solid content of the feed solution is 10%.
Then the average wet droplet size required is 3/0.1=30 micron. The liquid intake is about 8 L/hr, the compressed air needs 0.2 MPA, and the intersection point is about 30 micron.
For droplets of other sizes, first determine the treatment capacity, make a vertical axis, find the approximate size of the droplets, and then find the intersection point to find the compressed air pressure.
Note: According to the influence parameters of density and viscosity of materials on droplets, the final average diameter of droplets should be 30 [-27,33]
5.Device parameters
Ultrafine powder spray dryer | QFN -CX-3 | QFN -CX-Five | QFN -CX-Ten |
Water evaporation | 3Kg/h | 5Kg/h | 10Kg/h |
Minimum feed rate | 80ml | 80ml | 120ml |
Drying chamber diameter (mm) | ¢600 | ¢800 | ¢1200 |
Height of drying tower (mm) | ¢800 | ¢800 | ¢1500 |
Atomization structure | Single-hole misaligned atomization structure (QFN-CX-NZY8VER2018-1A) |
Electric control system | QFN-CX-ES-VER2018-1A |
Maximum intake temperature (Celsius) | Two hundred and sixty |
Standards for main electronic control accessories (including PLC, analog module, touch screen) (optional) | Dimension Control Module (Standard)Delta Control Module_German Siemens Control Module _Other________ |
Selection Standard for Electronic Control Auxiliary Parts (Contactors, etc.) (Optional) | Zhengtai (Standard) Delicious Schneider Others________ |
Contact with material (optional) | "9745; SUS304 (26631;" 20934; 160;"160;" 160;"160;" SUS316 "160;" 1600;"D"20854;"20182;uses |
Tail gas reuse, energy saving more than 30% (optional) | Non-assembly (Standard) Assembly |
Atomizing nozzle (whether diamond coating is used) | SUS304 (Standard) SUS316 (Standard) SiC (Standard) Diamond |
Equipment warranty | _1 year (standard, above need to charge a certain maintenance fee)2 years_3 years |
Heater capacity | 6Kw | 15Kw | 25Kw |
Blower [power (kw), air volume (m/min)] | nothing | nothing | [0.25,9.5] |
Induced draft fan [power (kw), air volume (m/h)] | [1.5,250] | [2.2,300] | [2.2,300] |
Compressor [Power (kw), Air Volume (L/min)] | [0.58,108] | [1.5,250] | [1.5,250] |
Electricity (installed capacity) | 8Kw | 30Kw | 40Kw |
Thermal insulation material | 50mm Glass Fiber Thermal Insulation Cotton | 50mm Glass Fiber Thermal Insulation Cotton | 50mm Glass Fiber Thermal Insulation Cotton |
_Pulse bag filter (optional) | Polytetrafluoro Film Coating Material |
4 only | 4 only | 9 Only |
Profile Size (mm) (L X W X H) Reference resources | 1600×1400×1800 | 2200×1600×2200 | 2600×1200×2500 |
Installation Weight (Reference) | 200Kg | 450Kg | 1000Kg |
Power Supply | 380V/-3(Relevant voltage can be customized according to different national standards) |
Note 1: Water evaporation to air temperature 250 C,.
2: If you need more evaporation equipment, please make an online inquiry or call our company.