EMUX600ESX Integrated Service Optic Access Equipment is developed and produced independently by Easy Broadband Technology (Beijing) Co., Ltd with its own ASICs. The E1 signal, Ethernet signal and telephone signal are mixed and encoded and transmitted on a pair of optical fibers by adopting time division multiplexing technology. Thus realizing E1 interface, 100M Ethernet service and telephone service transmission. The transmission channel includes optical transmission channel and VF transmission channel. This device......
1:General Overview
EMUX600ESX Integrated Service Optic Access Equipment is developed and produced independently by Easy Broadband Technology (Beijing) Co., Ltd with its own ASICs. The E1 signal, Ethernet signal and telephone signal are mixed and encoded and transmitted on a pair of optical fibers by adopting time division multiplexing technology. Thus realizing E1 interface, 100M Ethernet service and telephone service transmission. The transmission channel includes optical transmission channel and VF transmission channel. This device adopts 19"*6U design, high integration, low power consumption, reliable operation, easy to install and use.
2:Functions and Features
1:The device is with 19"*6U structure, adopt card type;
2:Provide 6 service slots and 1 power supply slot;
3:Service slots can plug optic transmission main card 240HA or E1 transmission main card such as MUX30A and MUX60;
4:240HA main card provides 2*optical ports(1+1 protection), 16*E1 ports, 8*FE ports(physical isolated), 30 channel telephone service slot port;
5:MUX30A main card provides 1*E1 port, 30 channel telephone service slot port;
6: MUX60 main card provides 2*E1 ports and 60 channel telephone service slot port;
7:Telephone interface contains over-voltage and lightning protection module;
8: Optical interface card optical non-relay transmission distance longer than 20 km, maximum 120 km;
9:330 channel telephone fiber optic multiplexer can be fully equipped with 1*optical interface card(main card) and 5*MUX60 interface card;
10:Power supply: 220V or -48V;
3:Technical indicators
1:Optical Interface
² Wavelength:1310nm(standard mode)or 1550nm
² Transmit Power:≥-12dBm
² Receiver Sensitivity:≤-30dBm(BER≤10-11)
² Interface Type:SFP(LC)
Transmission Mode:Dual Fiber or Single Fiber
2:E1 Interface
² The device has 4 channels E1 interface, in accordance with G.703
² Rate:2048Kb/s ±50ppm
² Code Type:HDB3
² Impedance:120Ω(balanced)
² Jitter:In accordance with G.742 G.823
² Attenuation: 0~6dB
3:Ethernet Interface
² Support line speed 10Base-T/100Base-T, Full duplex/half duplex self-adaptive
² In accordance with IEEE802.3/IEEE802.3u standard
² Use standard RJ45 connector
4:VF Interface and Signaling
l Exchange Side
Off-hook Impedance: < 500Ω
On-hook Impedance: > 10KΩ
l User Side
Loop Impedance: ≤2000Ω(include phone)
Idle Circuit Voltage ≤ 50V
Loop Current: 25mA
Off-hook Threshold: 8mA
Polarity Reversal Delay: < 50ms
Dial Up: Pulse dialing single pulse distortion< 5ms
The total distortion of internal audio dialing satisfies the characteristics of voice interface
Off-hook Delay: < 100ms
l Ringing Current:
Remote(FXS)Ringing Current Generator
Frequency: 25 Hz±3 Hz
Range: 75V±5Vrms
Ringing Current Time Delay < 50ms
Total Output Power ≤ 10W(in units of chassis)
Local(FXO)Ringing Current Detection
Range: Minimum 38Vrms
l VF Interface
Impedance: 600Ω or three-element compound impedance
5:Power Consumption
² Power Consumption of the whole machine <350W
6:Work Environment
² Operating Temperature: 0~45℃
² Relative Humidity: ≤95%(25℃)
² Atmospheric Pressure: 70~106Kpa