1、 Parameters:
1. Applicable materials: grasin paper, cigarette paper, white card paper, silicone oil paper, release paper, kraft paper and other paper materials
2. Cutting width: 100-1850mm
3. Effective width: 1850mm
4. Mechanical speed: 400m / min
5. Cutting speed: 350m / min (depending on cutting material)
6. Cutting and alignment accuracy: ≤± 0.10 mm
7. Flatness of the end face of the cutting tray: ≤± 0.20mm
8. Unwinding diameter: ≥ 1200 ㎜
9. Reeling core diameter: ¢ 3 ", 6" internal expanding mechanical chuck
10. Winding diameter: 2 * 〝800mm (can be increased appropriately)
11. Take up and lock: Φ 3 "inflatable shaft
12. Winding tension: automatic taper tension control
13. Unwinding motor: 7.5kW * 2 sets of three-phase asynchronous servo motors
14. Main motor: 11kw three-phase asynchronous servo motor
15. Winding motor: 11kw * 2 three-phase asynchronous servo motors
16. Exhaust fan: 2.2kW high-pressure three-phase AC fan, waste suction mode
17. Overall power: 50KW
18. Hydraulic workstation: working pressure < 15MPa, flow rate 15L / min, continuous operation, and continuous control of high and low speed of winding arm
19. Correction range: 120mm
20. External dimension: 8000 × 4800 × 2200mm (H)
21. Machine weight: about 6500kg
22. Working power supply: 380V ± 10% 50Hz ± 5%, three-phase five wire power supply.
23. Compressed air: clean, > 0.6MPa. Relative humidity of installation environment: 60% maximum. Environmental Science
Temperature: 40 ° C max.
2、 Configuration:
A) Unwinding device: (shaftless)
1. No shaft type hydraulic lifting linear guide type platform, the material is automatically lifted by the upper arm of the hydraulic platform under the action of the oil cylinder, with the minimum unwinding diameter of ¢ 500mm.
2. The ultrasonic automatic deviation correction system is used for edge and mark line control. The probe is fixed on the bracket. The unwinder can move left and right on the linear guide rail of the base plate under the action of DC motor. The adjustment speed is 15mm / s, the deviation correction range is ± 60mm, the printing face is downward, the accuracy is ± 0.5mm, and the electric eye can move in a whole range.
3. When the supporting structure of the double acting hydraulic arm is clamped, the left and right movements are adjusted simultaneously.
4. Maximum roll weight: 3000kg.
5. Unwinding tension: fully automatic algorithm control, PLC joint control. Docking device: a feeder plate can be longitudinally adjusted ± 15 degrees;
B. The material receiving plate is equipped with a knife groove, and the double cutting knife groove;
C. Adopt program-controlled paper receiving unit;
D. Adopt double pneumatic compression connection structure;
E. With lighting;
F. Adjustable time 0-60 seconds;
E. Lap range 15-25mm.
9. Two way rewinding, can be rewinding.
10. Unwinding film locking roller: the film can be locked automatically / manually when the machine is stopped.
B) Traction part: pneumatic roller traction system
1. Traction motor: 11kw three-phase asynchronous servo motor
2. Transmission mode: synchronous belt transmission
3. Working mode of press roll: pneumatic press roll, dynamic and static balance treatment
4. Main traction roller: adopt ¢ 150 mm hard chrome plated mirror roller, dynamic and static balance treatment
5. Encoder meter speed, Schneider
C) Slitting part: circular cutter system with swing pressure cutter structure
① Upper round knife: ¢ 105mm
② Lower round knife: ¢ 105mm
③ Active mode: synchronous belt drive
E) Exhaust system: adopt 2.2kW high-pressure three-phase fan to absorb waste
F) Reeling system: independent driving double shaft structure, with double tension mode of center surface.
1. Winding diameter: 2 × 10 800mm, end face tidiness ≤ ± 0.20mm
2. Reeling shaft: the inflatable shaft is 3 "swing the unloading structure.
3. Maximum tension: 50kg
4. Winding tension: it adopts the motor torque control, with the winding tension taper self-control and running dynamic tension control function.
5. Winding power: driven by 11kw * 2 asynchronous servo motor
6. Frequency converter: 11kw * 2, PLC joint control.
7. Winding drive: adopt arc tooth synchronous belt drive
8. Pressure structure: constant pressure mode, precision pressure regulating valve control.
1) Main control system: main control unit composed of PLC and weinview human-machine interface
J) Low voltage apparatus: Schneider
K) Pneumatic components: adek
50) Rolling element: C3 level inlet
M) Transition guide roller: φ 120mm duralumin alloy aluminum roller, dynamic and static balance treatment, hv700 type
3、 Main configuration list
product name | Specifications | Brand |
PLC PLC | S200 | Siemens |
touch screen |
| Willen Taiwan |
Module |
| Siemens |
Motor |
| Asynchronous servo |
Inverter |
| Yaskawa |
Correction |
| Dondon |
Pneumatic Components |
| Yadek |
Rolling element |
| German bem |
Cutting method |
| Round Knife (Shanghai) |
Curved roller |
| Domestic famous |
Air shaft |
| Shanghai |
Timing belt |
| Sino-Italian joint venture |
Flat belt |
| Made in Italy |
Linear guide |
| Domestic famous |
Electronically controlled proportional valve |
| SMC |
Precision pressure regulator |
| SMC |
Hydraulic station |
| Domestic famous |
Automatic loading without shaft | Hydraulic | Domestic famous |