Welcome Customer !

Membership

Zhejiang Saikong Electrical Technology Co., Ltd.
Free Member ·1YRS
,
Other

Main Products: 变频器

Xwboo>Technical Article>How to correctly select IGBT for photovoltaic inverter applications

Zhejiang Saikong Electrical Technology Co., Ltd.Free·1YRS

  • E-mail

    amy@safeinvert.com

  • Phone

  • Address

    #22 Liujiang Avenue, Liushi Town, Yueqing City, Zhejiang Province, China

Contact Now
How to correctly select IGBT for photovoltaic inverter applications
Date: 2022/11/4Read: 37

How to correctly select IGBT for photovoltaic inverter applications

Aug 30, 2021

How to correctly select IGBT for photovoltaic inverter applications

There are countless types of advanced power components on the market today, and it is indeed a difficult task for engineers to select the right power components for an application. For solar inverter applications, insulated gate bipolar transistors (IGBTs) can provide more benefits than other power components, including high current-carrying capacity, voltage instead of current control, and anti-parallel diodes Cooperate with IGBT. This article will introduce how to use the full-bridge inverter topology and select the appropriate IGBT to minimize the power consumption of solar applications.


A solar inverter is a power electronic circuit that converts the DC voltage of the solar panel into an AC voltage to drive AC loads such as household appliances, lighting, and electrical tools. As shown in Figure 1, the typical architecture of a solar inverter generally uses a four-switch full-bridge topology.




In Figure 1, Q1 and Q3 are designated as high-side IGBTs, and Q2 and Q4 are low-side IGBTs. The inverter is used to generate a single-phase sinusoidal voltage waveform under the frequency and voltage conditions of its target market. Some inverters are used in residential installations connected to the grid with net metering benefits. This is one of the target application markets. This application requires inverters to provide low-harmonic AC sinusoidal voltages so that electricity can be injected into the grid.


In order to meet this requirement, the IGBT can pulse-width modulate the frequency of 50Hz or 60Hz at a frequency of 20kHz or above, so the output inductors L1 and L2 can maintain a reasonable small size and can effectively suppress harmonics. In addition, since its conversion frequency is higher than the normal human auditory spectrum, this design can also minimize the audible noise generated by the inverter.


What is the best way to pulse width modulate these IGBTs? How can the power consumption be minimized? One of the methods is to perform pulse width modulation on only the high-side IGBT, and the corresponding low-side IGBT is commutated at 50 Hz or 60 Hz. Figure 2 shows a typical gate voltage signal. When Q1 is performing pulse width modulation, Q4 maintains positive half-cycle operation. Q2 and Q3 remain off during the positive half cycle. In the negative half cycle, when Q3 performs pulse width modulation, Q2 remains on. Q1 and Q4 are turned off during the negative half cycle. Figure 2 also shows the AC sinusoidal voltage waveform through the output filter capacitor C1.




This conversion technology has the following advantages: (1) The current does not flow freely on the high-voltage side anti-parallel diode, so unnecessary losses can be minimized. (2) The low-voltage side IGBT will only switch at 50Hz or 60Hz power frequency, mainly due to conduction loss. (3) Since the IGBTs on the same phase will never be converted in a complementary manner, it is impossible to cause a bus short-circuit breakdown. (4) The anti-parallel diode of the low-side IGBT can be optimized to minimize the loss caused by freewheeling and reverse recovery.


IGBT technology


IGBT is basically a bipolar transistor (BJT) with a metal gate oxide gate structure. This design allows the gate of the IGBT to be like a MOSFET, using voltage instead of current to control the switch. As a kind of BJT, IGBT has higher current handling capability than MOSFET. At the same time, IGBT is a minority carrier element like BJT. This means that the speed at which the IGBT turns off is determined by the speed at which a few carriers recombine. In addition, the turn-off time of the IGBT is inversely proportional to its collector-emitter saturation voltage (Vce(on)) (as shown in Figure 3).




Taking Figure 3 as an example, if the IGBT has the same size and technology, an overspeed IGBT has a higher Vce(on) than a standard speed IGBT. However, the turn-off speed of the overspeed IGBT is much faster than that of the standard IGBT. This relationship reflected in Figure 3 is achieved by controlling the use period of the IGBT's minority carrier recombination rate to affect the turn-off time.


Table 1 shows the parameter values of four IGBTs with the same size. The first three IGBTs use the same planar technology, but use different lifetime composite control metering. It can be seen from the table that the standard speed IGBT has the lowest Vce(on), but compared with the fast and ultra-speed planar IGBT, the standard speed IGBT has the slowest fall time. The fourth IGBT is an optimized slot-gate IGBT that can provide low conduction and switching losses for high-frequency switching applications such as solar inverters. Please note that the Vce(on) and total switching loss (Ets) of slot gate IGBTs are lower than those of ultra-speed planar IGBTs.




High-side IGBT


The previous article discussed the switching of the high-side IGBT at a frequency of 20kHz or above. Assuming that a 1.5kW solar inverter with 230V AC output is designed, which IGBT in Table 1 has the lowest power consumption? Figure 4 shows the power consumption analysis of IGBT switching at 20kHz, which shows that the ultra-speed planar IGBT has lower total power consumption than the other two planar IGBTs.




At 20kHz, the switching loss obviously becomes an important part of the total power consumption. At the same time, although the conduction loss of the standard speed IGBT is the lowest, its switching loss is the largest, and it is not suitable for acting as a high-side IGBT.


The latest 600V slot gate IGBT is optimized for 20kHz switching. As shown in Figure 5, this IGBT provides lower total power consumption than conventional planar IGBTs. Therefore, in order to achieve the highest efficiency in the design of solar inverters, trench gate IGBTs are the preferred components for high-side IGBTs.


Low-side IGBT


The low-side IGBT also has the same problem. Which IGBT can provide the lowest power consumption? Since these IGBTs can only switch at 50Hz or 60Hz, as shown in Figure 5, standard speed IGBTs can provide the lowest power consumption. Although the standard IGBT will bring some switching losses, the value is not enough to affect the total power consumption of the IGBT. In fact, the latest slot-gate IGBT still has higher power consumption, because this generation of slot-gate IGBT is specifically designed for high-frequency applications, with the goal of balancing switching and conduction losses. Therefore, for low-side IGBTs, standard-speed planar IGBTs are still an inevitable choice.




Summary of this article


This article analyzes the full-bridge topology for solar inverter applications. This topology uses sinusoidal pulse-width modulation technology to convert the high-side IGBT at higher than 20kHz. The low-voltage side IGBT of the branch line depends on the output frequency requirement, and it is converted at 50Hz or 60Hz. If you choose the latest 600V slot gate IGBT, its total power consumption will reach the lowest at 20kHz. For low-side IGBTs, standard-speed planar IGBTs are the best choice. Standard speed IGBT has the lowest conduction loss at 50Hz or 60Hz, and its switching loss is insignificant to the overall power consumption. Therefore, as long as the engineer chooses the correct IGBT combination, the power consumption of solar inverter applications can be minimized.