Portable chloroform gas detector MS400-CHCL3

Features of MS400 portable chloroform gas detector:

● Waterproof, dustproof, explosion-proof, shockproof, intrinsically safe circuit design, anti-static, anti-electromagnetic interference, passed the national standard test and CPA form approval

●Protection level IP65, built-in water vapor and dust filter to prevent damage to sensors and instruments due to water vapor and dust

●Built-in pump suction measurement, integrated water vapor and dust filter, optional professional accessories for high temperature, high humidity, high dust environment, special road design, rapid response.

●The 2.31-inch high-definition color screen displays real-time concentration, alarm, time, temperature, humidity, storage, communication, power, charging status and other information. The menu interface uses high-definition simulation icons to display the function names of each menu

●Large-capacity data storage function, standard 100,000 data storage capacity, larger capacity can be customized. It supports real-time storage, timing storage, or only alarm concentration data and time, supports viewing and deleting data on this machine, and also uploads data to a computer through the USB interface, and analyzes the data with upper computer software and stores and prints.

●USB charging port, can be charged by computer or power bank, compatible with phone charger, overcharge, overdischarge, overvoltage, short circuit, overheat protection, 5-level accurate power display, support USB hot plug, the tester can be normal when charging Work, optional RS485 communication

●Using 4600mAH high-capacity rechargeable polymer battery, which can work continuously for a long time

●Sound and light alarm, vibration alarm, visual alarm, under-voltage alarm, fault alarm, multi-directional three-dimensional display of alarm status when alarming.

●Alarm value can be set, the alarm mode can be low alarm, high alarm, interval alarm, weighted average alarm

●High-precision temperature and humidity measurement (optional), while temperature compensation is performed on the sensor. The temperature range of the instrument is -40 to 70 degrees, and it can detect 400 degrees of gas. The detection of higher temperature gas can be customized (optional high temperature sampling and cooling Filter handle or high temperature and high humidity pretreatment system)

●It can be selected to detect 1 to 4 kinds of gases at the same time, and the units can be switched freely. Normal gases do not need to enter the molecular weight. Special gases need to enter the molecular weight to automatically calculate and switch. The units are optional: PPM, mg/m3, Vol%, LEL%, PPHM, ppb, mg/L

●Three display modes can be switched: display the concentration of four gases at the same time, the concentration of a single channel gas and the real-time curve can be displayed in a large font cycle, and the automatic cycle or manual cycle between the channels can be switched. Gas name, you can view the history curve graph.

●Chinese and English interface can be selected, the default Chinese interface, concise Chinese or English operation prompts

●Data recovery function, you can recover selectively or fully

●Zero point automatic tracking, long-term use will not be affected by zero point drift.

●Three-level calibration of the target point to ensure the linearity and accuracy of the measurement.

●Mistaken operation of concentration calibration is automatically identified and prevented, which can avoid defects caused by human factors.

●Real-time detection or timing detection is possible (for the case where the amount of the gas to be measured is relatively small), the pump can be turned off when it is not detected to extend the startup time.

Technical parameters of MS400 portable chloroform gas detector:

Detection gas: chloroform CHCL3, optional: simultaneous detection of 1 to 4 gas concentrations and temperature and humidity measurement, depending on the sensor and the site environment

Detection range: 0-10, 100ppm, other ranges can be customized

Resolution: 0.01ppm higher resolution can be customized

Detection principle: electrochemistry, other principles are optional, according to gas type, range, site environment and user needs

Sensor life: 2-3 years

Detection method: built-in pump suction type, flow rate 500 ml/min

Display mode: 2.31 inch 320X240 high-definition color screen display, 5-button operation

Detection accuracy: ≤±3% (F.S) (higher accuracy can be customized)

Linearity: ≤±2%

Repeatability: ≤±2%

Alarm mode: sound and light alarm, vibration alarm, visual alarm, sound and light + vibration + visual alarm, close alarm optional

Response time: T90≤20 seconds

Recovery time: ≤30 seconds

Power supply: DC3.7V

Battery capacity: 3.7VDC, 4600mAH high-capacity rechargeable polymer battery, with overcharge, overdischarge, overvoltage, overheating, and short circuit protection functions

Use environment: temperature -40℃~+70℃; relative humidity ≤0-99%RH (built-in filter can be used in high humidity or high dust environment)

Sample gas temperature: -40℃~+70℃, optional high temperature sampling cooling filter handle, can detect the flue gas concentration at 400 degrees or higher

Temperature measurement: -40℃~+70℃ (optional), accuracy 0.5℃

Humidity measurement: 0-99%RH (optional), accuracy 3%RH

Data storage: Standard configuration of 100,000 pieces of data capacity, support for viewing, deleting or exporting data from the machine, equipped with host computer communication software, the storage function is off by default, and can be set to on, and the storage time interval can be set arbitrarily

Communication interface: USB (charging and communication), optional RS485 communication interface

Interface language: Chinese or English can be set, the default Chinese interface

Explosion-proof type: intrinsically safe

Explosion-proof mark: Exia II CT4Ga

Protection grade: IP65, dustproof and splashproof

Dimensions: 178×67×40mm(L×W×H)

Weight: 300g

Standard accessories: manual, certificate, warranty card, USB charger (including data cable), high-grade aluminum alloy instrument case, alligator clip, host computer communication software, humidity and dust filter 1

Optional accessories: temperature and humidity measurement function, 0.9m retractable sampling handle (1-10m hose, standard length 1m), high temperature sampling cooling filter handle, high temperature and high humidity pretreatment system, multiple humidity dust filters, hanging rope

Application occasions: petroleum, chemical, pharmaceutical, environmental protection, flue gas analysis, air treatment and other occasions where gas concentration needs to be detected

Sorry  There is no "Application", you can view other services。