Welcome Customer !

Membership

XwbooMachine Tool AccessoriesMachine Tool Functional PartsMotor3hp 3 Phase Motor
  • $item.Title
  • $item.Title

3hp 3 Phase Motor

Liyuan Motor Ltd

Model
Nature of the Manufacturer
Other
Product Category
Motor
Place of Origin
,
MS series aluminum housing 3hp 3 phase motor is made of superior materials and conform to the IEC standard.

Product Introduction

MS series aluminum housing 3hp 3 phase motor is made of superior materials and conform to the IEC standard. MS motors have good performance, low noise, safety, reliable operation and nice appearance. It can be maintained very conveniently. This 3 hp motor 3 phase has advantages of little vibration, light weight and simple construction. These motor can be used for general drive such as water pumps, water treatment, road machinery, petroleum, chemical, metallurgy, cement and paper industries.


Product Detail



Motor Type: 3 phase 3hp motor

Output Power: 0.06 kW - 18.5 kW

Frame Size: IEC Frame 56 - 160

Number of Poles: 2 / 4 / 6 / 8

Voltage: 220/380V, 380/660V, 230/400V, 400/690V

Frequency: 50 & 60 Hz

Protection Level: IP54 / IP55

Energy Efficiency Rating: IE1 / IE2 / IE3

Insulation Class: B/F

Cooling Method: IC411

Working System: S1


Product Parameter (Specification)



Motor 3 horsepower

Type

Power HP

Rated Current (A)

Speed (r/min)

Eff (%)

Power Factor CosØ

Rated Torque Tn(N*m)

Tst/Tn

Tmax/Tn

Ist/In

220V

380V

660V

230V

400V

690V

3000rpm.2 poles

MS2-90L-2

3

8.16

4.71

2.72

7.78

4.49

2.59

2860

83.2

0.85

7.35

2.3

2.3

7.6

1500rpm.4 poles

MS2-100L1-4

3

8.56

4.94

2.85

8.16

4.71

2.72

1440

84.3

0.8

14.59

2.3

2.3

7.3

1000rpm. 6 poles

MS2-112M-6

3

9.8

5.66

3.27

9.34

5.39

3.11

945

81.8

0.72

22.23

2

2.1

6.2


Production Features


image001

Know More Us


image006

Why Us


image008

Service and Packing


image009

About motor knowledge



Liyuan Motor Analyzes the Motor's Sweeping Trouble

Many people don't know the cause of the motor's borehole failure. This article will give you an analysis of the editor of Liyuan Motor.


When the gap between the inner ring and the journal or the outer ring and the end cover of the bearing is greater than 0.1mm, the stator and rotor may rub (sweep). When the bore is lighter, the motor can still start and run, but the temperature rises, and the winding will burn out for a long time, and it cannot start and run when it is heavier. Disassembling the motor with the failure of the sweeping bore can see the purple-blue scratched surface. Most of the motors that have the phenomenon of bearing rotating sleeves are aluminum shell motors.


The reasons for the transfer are:

a. Poor processing accuracy;

b. Frequent and unreasonable disassembly and assembly. The inner sleeve of the bearing and the journal are tightly fitted, and the outer sleeve and the end cover are processed into a zero fit or a slight tightness


In some motors, special steel sheets are installed between the outer shell and the end cover to prevent the bearing jacket from rotating. Some bearing up and down (the bearing should be heated for correct disassembly and assembly) or the anti-rotation steel sheet is lost, which will cause the phenomenon of bearing rotation. For motors with bearing rotating sleeve phenomenon, in the past, most of the motor bearings were repaired by the chiseling method, but the effect (especially the end cover) was not ideal. Practice believes that the use of adhesive method to repair motor bearings, the effect is better.


Metallic glue is used for motors with higher power and higher speed, and chlorine tincture glue for motors with lower power and lower speed. The maintenance method is to clean the rotating sleeve first, add grease, and then apply glue, and then install the motor. For the more serious rotating sleeve, the gap between the inner ring of the bearing and the journal or the outer cover and the end cover is large, a metal sheet of appropriate thickness can be used to pad in the gap. In order to ensure concentricity, the metal sheet should be made into an oblique mouth. The practice of repairing motor bearings shows that most motors can be restored to normal by coating them with appropriate glue in the motor bearing gaps.



Our HistoryLiyuan Motor Ltd, founded in 1989, is located in Fuan city, the electric motor town of China. Our company has floor area of 3500 square meters and is a professional manufacturer of small and medium size electric motors, equipped with advanced facilities, advanced production and perfect testing equipments. We are the excellent medium-small size motor manufacturer in China, aiming to provide the highest quality but lowest price to our clients.Our FactoryNow, We have a integrated team of high skilled technicians and professional salesmen with advanced product-development method and modernized management system. In order to manufacture high quality products, we make sure we take strict procedure controls, from “material select”, “machining”, “producing”. “assembling”, and “testing”, on each single part. All of our products are produced by national standard and reach the high level in China. Products is hot sale not only in domestic market also oversea regions such as South-East Asia, Middle Asia etc. Motors are quite welcomed and we received thousands good comments from customers.Our ProductThe main business of the company specially produces the cast-iron electric motor such as Y/Y2/IE2 general motor, YEJ break motor, YVF frequency controlled motor, YD multi-speed motor, YC/YCL/YL single phase motor, YTY pump motor, YLJ break motor etc and alluminum motor such as MS general motor, ML/MC single phase motor as well as brushed DC motor and brushed permanent magnet DC motor.
Similar Product Recommend